lancer 2308 Series Manuals

COLD CARB ICE COOLED DISPENSER SERIES 2308 - DROP IN “Lancer” is the registered trademark of Lancer © 2009 by Lancer, all rights reserved. LANCER 6655 Lancer Blvd. San Antonio, Texas 78219 To order parts, call Customer Service: 800-729-1500 Warranty/Technical Support: 800-729-1550 Email: [email protected] www.lancercorp.com Installation and Service Manual PN 28-0720/05 11/10/09 ISO 9001:2000 Quality System Certified

DATE: July 2012 P.N. 28–0896 6655 LANCER BLvD. • SAN ANTONIO, TEXAS 78219 USA • (210) 310-7000 "Lancer" is the registered trademark of Lancer • Copyright - 2012 by Lancer, all rights reserved. 1. INSTALLATION OVERVIEW 1.1 RECEIVING Each unit is completely tested under operating conditions and thoroughly inspected before shipment. At time of shipment, the carrier accepts the unit and any claim for damage(s) must be made with carrier. Upon receiving units from the delivering carrier, carefully inspect carton for visible indication(s) of damage. If damage exists, have carrier note same on bill of lading and file a claim with the carrier. 1.2 RECEIVING/UNpACKING A. Set shipping carton upright on the floor. Cut band and remove. Open top of carton & remove interior packing. B. Lift carton up and off of the dispenser. Remove wood shipping base from the bottom of the dispenser. (Support dispenser while removing shipping base to prevent damage to the dispenser.) C. Remove installation parts kits from the ice compartment. Ensure items listed on the install kit checklist are provided. D. Inspect unit and parts for concealed damage(s). If damage exists, notify delivering carrier and file a claim against the carrier. 1.3 DRAIN SpIDER The drain spider (Fig 1) is located to the right side near the front of the bin under the ice shroud. The coldplate has a cavity designed to hold the drain spider. During shipment or installation, the drain spider may become dislodged from its original position. Prior to installing the dispenser, ensure the drain spider is in the correct position.This will prevent drain clog issues. Inspect the lower bin area and reach under the shroud to ensure the drain spider is secure in the coldplate cutout. If spider is not in place, locate drain spider and reinstall in the cold plate cavity where drain line exits. 1.4 SELECTING THE LOCATION Connecting lines can be run through the back of the dispenser or extend down through a counter cutout. Seal the dispenser directly on the countertop. Counter Cutouts for each unit are included in the Installation Kit and in Section 6. Illustrations and parts Listings of the Operations & Service Manual pN 28-0897, available on the Lancer website. A. Select a level, well-ventilated, accessible location away from direct sunlight or overhead lighting (convenient to water, soda, and syrup lines and open type drain), a properly grounded electric supply and ensure sufficient clearance for air circulation. NOTE: Sufficient clearance must be provided, to allow for filling the ice compartment with a five gallon bucket (minimum of 16” is recommended). FOR QUALIFIED INSTALLER ONLY. This basic Installation Sheet is an initial release. If a complete Installation and Service Manual (for the unit being installed) is required or needed, please refer to the Lancer web site (www.lancercorp.com) for immediate access. Contact Lancer Customer Service for assistance as required. ! WARNING The dispenser is for indoor use only. This unit is not a toy. Dispenser is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instruction concerning use of the appli- ance by a person responsible for their safety. Unit is not designed to dispense dairy products. The min/max ambient operating temperature for the dispenser is 40 to 90 degrees F. ! ADVERTENCIA El dispensador sólo debe usarse en interiores. Esta unidad no es un juguete. Esta unidad no está destinada al uso por parte de personas (incluso niños) con capacidad física, sensorial o mental reducida, o sin experiencia y conocimientos suficientes, a menos que una per- sona responsable de su seguridad les haya dado supervisión o capacitación en el uso de la unidad. Esta unidad no ha sido diseñada para sumin- istrar productos lácteos. La temperatura ambiente operativa mínima / máxima para el dispensador es de 40 a 90 grados F. ! AVERTISSEMENT Le distributeur est destiné à un usage à l'intérieur seulement. Cet appareil n'est pas un jouet. Il ne devrait pasêtre utilisé par des enfants ou des personnes infirmes sans surveillance. Cet appareil n’est pas destiné à un usage par des personnes (y compris les enfants) ayant des capacités physiques, sensorielles ou mentales réduites, ou manquant d'expérience et de connaissances, à moins qu'elles obtiennent de la sur- veillance ou des instructions au sujet de l'utilisation de l'appareil de la part d'une personne chargée de leur sécurité. Cet appareil n'est pas conçu pour distribuer des produits laitiers. La température de service ambiante minimum/maximum pour le distributeur estde 40 à 90 degrés F. TOOLS REQUIRED: Oetiker Pliers, Wrench, Slotted & Phillips Screwdriver, Tubing Cutters, Precision Cutters, & Cordless Drill C O N T I N U E D O N N E X T P A G E LANCER INSTALLATION SHEET COLD CARb ICE COOLED DISpENSER, SERIES 2308 - bLUE SKY DROp IN Drain Spider ! WARNING To avoid personal injury or damage, do not attempt to lift a unit without help. For heavier units, use of a mechanical lift may be appro- priate. Units are equipped with automatic agitation. The unit may activate unexpectedly. Do not place hands, or foreign objects into the ice storage compartment. Unplug dispenser from the power source , when unit is being serviced, cleaned, or sanitized. ! ADVERTENCIA Evite las lesiones personales, no trate de levantar el dispensador sin ayuda. Para los dispensadores màs pesados use un elevador mecánico. Las unidades equipadas con agitación automática se activan repentinamente. No ponga las manos ni objetos extranos en el compartimiento de almacenamiento de hielo. Desenchufe el dispensador durante tareas de servicio, limpieza y esterilización. ! AVERTISSEMENT Pour éviter des blessures ou des dommages, n’essayez pas de soulever une unité sans aide. Pour les unités plus lourdes, l'utilisation d’un ascenseur mécanique peut être appropriée. Les unités sont équipées d’une agitation automatique. L'unité peut s’activer demainére inattendue. Ne placez pas les mains, ou des corps étrangers dans le compartiment de stockage de glace. Débranchez le distributeur de la source d’alimentation en électricité quand l'unité est entretenue, nettoyée ou aseptisée.