Leviton IPF01-1L Manuals

Single Pole (One location) or 3-Way (Multi-location) Quiet Fan Speed Control 120VAC, 60Hz Cat. No. IPFØ1-1L, 1.5A (Lighted) INSTALLATION INSTRUCTIONS DI-000-IPF01-02B Tools needed to install your Fan Speed Control: Slotted/Philips Screwdriver Electrical Tape Pliers Pencil Cutters Ruler Changing the color of your Fan Speed Control: Your Fan Speed Control includes two color options. The Control ships with the White frame attached. To change color of frame, proceed as follows: Position the Slide Switch Shaft with the opening in the frame and line up the plastic snaps with the square holes in the strap.. Installing Fan Speed Control by itself or with other devices: If installing Control in a single device application, proceed with the INSTALLING YOUR FAN SPEED CONTROL section. If installing Control in a multi-device application, proceed as follows: MULTI-DEVICE APPLICATION: NOTE: You only need to remove side sections if installing with other controls or if it does not fit in wall box – not when installing with mechanical switches. NOTE: There is NO derating necessary for multi-gang installations of this Fan Speed Control. INSTALLING YOUR FAN SPEED CONTROL NOTE: Use check boxes when Steps are completed. WARNING: To avoid fire, shock, or death; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! Removing existing switch: Remove existing wallplate and switch mounting screws. Carefully pull switch from wall box. DO NOT remove wires attached to the switch at this time. Identifying your wiring application (most common): NOTE: If the wiring in the wall box does not resemble any of these configurations, consult a qualified electrician. Step 2 Step 4 Step 1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF Single-Pole: Look at the back of your switch. If there are 2 wires connected to two screw terminals (not including a green or bare copper wire used for grounding), you have a Single-Pole switch. Step 3 con’t 3-Way: Look at the back of your switch. If there are 3 wires connected to three screw terminals (not including a green or bare copper wire used for grounding), you have a 3-Way switch. Note that one of the screw terminals will usually be a different color (black) or labeled Common. Tag that wire with electrical tape to identify. Tag Common Screw Wire Push in side at tab to release Line up tabs on back of slider to switch shaft and press in side to attach WARNINGS AND CAUTIONS: • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician. • To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer-operated appliance other than appropriate ceiling fans. • To reduce the risk of fire or electrical shock, this control is to be used with ceiling fans that are rated 120VAC, total load 1.5 amperes maximum. WARNINGS AND CAUTIONS: • For use on ceiling paddle fans with split-capacitor or shaded pole motors only. Please refer to manufacture's instructions or rating label on the motor to confirm type. Use with any other types of motors or equipment may cause overheating and/or damge to the motors or equipment. • Use only one (1) Fan Speed Control per load. The switch(es) will turn ON the fan at the speed level selected at the control. • Disconnect power at circuit breaker or fuse when servicing fixture. • Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL. Bend back and forth to remove side section Remove all inner side sections Do not remove outer side sections • Disconnect wires from screw terminals or Quickwire™ slots (shown). • Pull off pre-cut insulation from Control leads. • Make sure that the ends of the wires from the wall box are straight (cut if necessary). • Remove 5/8" (1.6 cm) of insulation from each wire in the wall box (shown). • For Single-Pole Application, go to Step 5A. • For 3-Way Application, go to Step 5B. Strip 5/8" Cut (if necessary) Press in slot and pull out wire Strip Gage 5/8" √ Step 3 Disconnecting switch wires and preparing wires: