Document Preview & Text Transcription
23 Inch Interactive Smart Shelf (ISS)
Product manual
(V1.0)
Please read the manual carefully in order to use the ISS well.
（In the following we will refer to this product collectively as ISS）
Version
Date
Page
Description
Ver 1.0
12th October,20’
ALL
First issued
REVISION HISTORY
Model: LD230EKS-FPN1/LD230EKS-FPN2
CMMI ID：2020DJ12750
.
.
.
.
..
DIRECTORY
1. Safety notice ...................................................... 2
2. ISS Components ............................................... 2
3. Pre-installation Instructions ............................... 3
4. Installation Precautions ..................................... 3
5. ISS details ......................................................... 4
6. External device ................................................. 4
7. System Introduction .......................................... 4
8. FCC WARNING ................................................ 7
9. RoHS ................................................................ 7
Appendix ............................................................... 8
ISS Size ................................................................ 8
1
2
• Please read the following instructions carefully before using ISS.
• DO NOT use ISS near water or install in a high temperature envi
ronment
• DO NOT use ISS near water or install in a high-humidity environ
ment
• DO NOT place ISS in direct sunlight or install near any heat sour
ces (such as radiators, heat registers or stoves).
•. DO NOT block any ventilation openings. Leave at least 10cm s
pace around the ISS.
• NEVER place ISS on an unstable cart, stand, bracket or table. It
may cause serious personal injury, death or serious damage to th
e ISS.
• When installing ISS, please make sure that the power plug and
socket are easily connected, and protect the power cord from bei
ng trampled or squeezed.
• DO NOT overload the wall outlets and connect too many applian
ces to the same AC power outlet.
• DO NOT use any unapproved items or cables to connect to ISS.
• ONLY USE accessories specified by the manufacturer.
• Clean only with a dry cloth and turn the power off before cleanin
g.
• Keep ISS and all package contents(including the EPE foam pac
kaging cushion and protective board) out of the reach of children
at all times
• Never attempt to repair or open ISS by yourself. Opening and r
emoving the covers may expose you to dangerous voltage or oth
er hazards. Failure to follow this WARNING may result in death or
serious injury. Please contact your dealer or a service technician f
or assistance.
• Watching the screen too much time may hurt your eyesight. Res
t your eyes for 10 minutes after 30 minutes of screen time.
▲ Warning : If using a Class 1 adapter, connect only to a grounde
d electrical outlet.
Consult an authorized service technician if ISS does not operate
normally when you have followed the instructions in this manual.
1. Safety notice
Check the following items in the box. If any attachments ar
e missing, contact your local dealer where you purchased t
he ISS. Illustrations in this manual may differ from actual IS
Ss and projects.
ISS x 6
2. ISS Components
Please check the packaging first before unpack ISS. Prepare a flat and stable surface near a wall outlet.
Set the ISS box in an upright position according to the arrow markings on the outside of the ISS box.
procedure
1.Open the ISS box from
the top side.
2.The top picture of the
package is as below.
3.Remove the insulation
foam on the top layer.
4.Take out the ISS one by
one from the isolation
layer of the second layer.
5.Remove the aluminum
foil wrapper from each ISS.
diagram
Carry
Put
When placing the ISS, always place
the screen face down according to the
instructions in the following section.
Do not stand the ISS upright.
Do not use the four corners of the out
side frame to support the ISS.
WLan Antenna
The top of the display has an antenna for WLan
connectivity. When installing the ISS, make sure
that no objects are placed on the wireless anten
na and that there are no metal objects or equip
ment in the area around the antenna.
Otherwise, the wireless signal will be weak or ev
en no signal.
The back of the display is equipped with three
screw-holes that allow for mounting. Firmly secu
re a mount onto the display using three M3x6m
m length screws (maximum torque: 4 kgf-cm).
4. Installation Precautions
To avoid injuries, follow the installation instructions to safely install the ISS onto a wall.
It is recommended to allow a certified installation company conduct the wall mounting operation.
▲ CAUTION : Accidental dropping of the ISS may injure others.
NOTE: A wall mount may be purchased separately for easier installation.
If you want to use ISS vertically or horizontally, ple
ase adjust the ISS, make sure that the output and
input ports of the ISS are free from obstructions, o
therwise the ISS may not work.
Please make sure that there is enough space to pl
ace the ISS before installation. For detailed dimen
sions, please refer to the last page of this instructi
on.
Holes of rear plate
When carrying the ISS, be sure to hold the
ISS firmly with both hands.
Do not apply force on the screen while hol
ding it.
Avoid applying force or using sharp objects
on the screen at all times.
When placing the ISS down, place the screen face down on a flat and stable surface covered by a
protection sheet and table mat, as shown in the illustration provided.
Never press or place anything on the rear cover. This may damage the internal parts of the ISS.
5. ISS details
Introduction to external interface
Interface
Function
DC PWR IN
Connect the adapter to power the ISS
Micro USB*1（OTG）
Connect to a computer via a USB cable to debug the ISS
Micro USB*1
Connect external storage devices containing videos or pictures or
peripherals such as mouse and keyboard
Micro HDMI
Connect the ISS to the second monitor via an HDMI cable, and
output the screen to the second monitor
RESET
1.Short press 1S to turn off the screen
2.Short press 3S to turn off the ISS and enter standby mode
3.Long press 7S to reset
The following image and table show the location of the connectors and other components.
Instructions for Power Connection
1.Connect the adapter Type-C interface to the “DC PWR-
IN” interface.
2.Fully plug the power cord into the power socket.
.
Note:
• Adapters vary depending on the country of purchase of the device.
• In all cases, use a power cord that matches the
AC voltage of the power outlet and has been approved and complied
with the safety standards of your country/region.
• Be sure to use the appropriate AC/DC adapter:
NOTE: Before connecting, make sure that all connected devices are powered off, and then turn on the powe
r for each device（including the ISS) after establishing the connection.
NOTE: The display only supports the following vide
o/image file formats (with their listed resolution) via
the Micro-USB port:
JPEG/BMP/GIF/PNG/MPEG AUDIO/WAV AUDIO/
OGG AUDIO/FLAC AUDIO/MIDI AUDIO/H.263/VP8
3
4
1.Connect the Micro USB adapter cable or Micro USB h
ub to the Micro USB interface of the ISS.
2.Connect any device below to Micro USB adapter cable
or Micro USB hub
•After the flash drive, keyboard or mouse is connected, y
ou can find the video/image files located on the flash driv
e in the file manager.
7. System Introduction
After connecting the power, the ISS will automatically turn on.
CAUTION：Loose adapter plugs may cause current
noise, please do not plug and unplug the adapter repeatedly.
6. External device
Use Micro USB connection
Setting
External monitor
You can use the Settings menu in the system to adjust the settings of many ISS.
1. Select the "All Applications" button on the right side of the main screen to enter the
"All Applications" menu. Or, swipe up from the bottom edge of the screen.
（As shown in Figure 1）
2. Select “Setting” in the "All Applications" list.（As shown in Figure 2）
1.Connect the appropriate adapter to the Type-C power input port on the ISS.
2.Connect the Micro-HDMI cable to the Micro- HDMI output port on the ISS.
3.Connect the other end of the Micro-HDMI cable to the HDMI input port of
other displays, and the display will start to copy the screen on the ISS.
3. Pre-installation Instructions
Unpack
Warning: When disconnecting the AC power cord,
be sure to unplug the adapter from the socket.
We recommend that you use this adaptor.
UL Listed Power Supply Unit marked "Class 2" or
"LPS" or "PS2" and rated min. 12 V DC, 3A
By default, the ISS automatically outputs its video to the external display, b
ut if the ISS settings are changed, the video output may be disabled.
To re- enable the video output to the external display, please follow the
instructions below:
Note: The screen of this ISS is a touch screen, which supports menu sele
ction by touch.
1.Turn on the main display.
2.Select the "All Applications" button on the right side of the main
screen to enter the "All Applications" menu. Or swipe up from the
bottom edge of the screen.(As shown in Figure 1)
3.Select “Setting” in the "All Applications" list.(As shown in Figure 2)
4.Select "Display" in the "Device" area of the "Settings" menu.
(As shown in Figure 3)
5.Select "HDMI Settings" in the "Display" menu.(As shown in Figure4)
6.Enable HDMI in the menu.(As shown in Figure 5)
Figure 2
Figure 3
Figure 4
Figure 5
Figure 8
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 10
Figure 6
Figure 7
Figure 9
Figure 1
5
6
After powering on the ISS, you must follow the
steps below to connect the ISS to the wireless
router:
1.Select the "All Applications" button on the right
side of the main screen to enter the "All Applic
ations" menu or swipe up from the bottom edg
e of the screen. (As shown in Figure 1)
2.Select “Setting” in the "All Applications" list. (A
s shown Figure 2）
3.Select "WLAN" in the "Settings" menu area. (A
s shown in Figure 6）
4.Make sure the WLAN switch is enabled. (As sh
own in Figure 7）
5.Select the SSID of the router to be connected.
To connect to an encrypted wireless hotspot, y
ou need to enter the hotspot password.
6.Return to the "All Applications" list. In the "All A
pplications" menu, select the "Browser" Applica
tion, and then open a web page to ensure that
you have correctly connected to the wireless n
etwork. (As shown in Figure 8）
Bluetooth connection settings
1. Select "Bluetooth" in the "Settings" menu. (As
shown in Figure 9）
2. Make sure that the Bluetooth switch is enabled.
(As shown in Figure 10）
3. Select the device to be paired.
Install the application
1.Select the "All Applications" button on the right
side of the main screen to enter the "All Applica
tions" menu. Or, swipe up from the bottom edge
of the screen. (As shown in Figure 1）
2.In the "All Applications" menu, select "Explorer
(As shown in Figure 14）
3.Find the location of the program installation file
in the resource manager, and then select the fil
e (take QQ as an example below).(As shown in
Figure 15）
4.Select "Install" in the confirmation message tha
t appears. The application will begin to install.
(As shown in Figure 16）
5.Select "Open".（As shown in Figure 17）
6.After installing the application, you can open
this application in the "All Applications" screen.
(As shown in Figure 18）
Connect to Internet
System language setting
Change the display language from the settings me
nu.
1. Select "Language and Input Method" in the "Pers
onal" area of the "Settings" menu. (As shown in
Figure 11）
2.Select "Language" in the "Language and input“ m
enu. (As shown in Figure 12）
3.Use the "bar" icon on the right side of the menu t
o drag the desired language from the default lan
guage list to the top or click "Add Language".(As
shown in Figure 13）
