Lightolier END FEED AND FLOATING CANOPY MOUNTING KIT Manuals

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC® TRACK ITEM. This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code specifications. To assure full compliance with codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Retain these instructions for maintenance reference. LIGHTOLIER a GENLYTE company. 631 Airport Road, Fall River, MA 02720 ® INSTRUCTION SHEET NO. IS:26060 0597 Page 1 of 2 END FEED AND FLOATING CANOPY MOUNTING KIT - FLUSH AND STANDOFF VERSIONS FOR USE WITH PROSPEC® SURFACE MOUNT TRACK SYSTEMS ONLY END FEED MOUNTING INSTRUCTIONS (Flush 26060WH, BK and Standoff 26061WH, BK) Mounting the CANOPY at the end of FEED TRACK or directly above a FEED CONNECTOR. 1. Mark CENTER LINE for TRACK through CENTER LINE of OUT- LET BOX. 2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET BOX. The MOUNTING HOLES of the OUTLET BOX should be at 45° to the longitudinal axis of the TRACK. (Fig. 1) 3. Remove the KNOCK OUT PLATE from the FEED TRACK or CONNECTOR (retain the SCREW). (Fig. 2) 4. Prepare TAB on the PLATE ASSEMBLY as follows: • FEED TRACK: DO NOT BREAK ANY TAB. (Fig. 2) • POWER EXTENSION, IN-LINE, “T”, AND “X” CONNECTORS: BREAK THE 90° TAB OFF THE PLATE ASSEMBLY. (Fig. 3) • “L” CONNECTOR: BREAK THE 90° TAB AND THE STRAIGHT TAB FROM THE PLATE ASSEMBLY. (Fig. 4) 5. Attach the PLATE ASSEMBLY onto the FEED TRACK or CONNECTOR using the SCREW. (Fig. 2 & 3) 6. Mount the TRACK to the ceiling (see instruction sheet IS:26000 provided with the TRACK) passing the wires through the center of the PLATE ASSEMBLY. 7. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with the MOUNTING HOLES on the J-BOX. 8. Secure the PLATE ASSEMBLY to the J-BOX using the THIN HEAD SCREWS. (Fig. 5) 9. Attach the GROUND WIRE on the CANOPY PLATE to the GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 5) 10. WHEN USING THE FLUSH CANOPY 26060WH/BK. Slide the CANOPY PLATE between the CONNECTOR and CROSS BAR on the PLATE ASSEMBLY. For added security of CANOPY PLATE: Drill a hole in CANOPY PLATE and secure to ceiling with a screw. 11. WHEN USING THE STANDOFF CANOPY 26061WH/BK Slide the CANOPY PLATE between the CROSS BAR and NUT on the PLATE ASSEMBLY. Rotate the NUT to secure the CANOPY PLATE against the ceiling. (Fig. 8) NOTE: THE CROSS BAR MUST COVER THE SLOT IN THE CANOPY PLATE AFTER ASSEMBLY. 12. Follow the instructions for wiring on the instruction sheet included with the “FEED TRACK” or “CONNECTOR”. CAUTION: TURN OFF POWER AT FUSE BOX BEFORE INSTALLING THE CANOPY KIT POWER EXTENSION CONNECTOR PLATE ASSEMBLY SCREW 90°TAB KNOCK OUT PLATE FIG. 2 FIG. 3 PLATE ASSEMBLY SCREW KNOCK OUT PLATE FEED TRACK FIG. 4 STRAIGHT TAB PLATE ASSEMBLY 90°TAB KNOCK OUT PLATE “L” CONNECTOR CANOPY PLATE GROUND WIRE THIN HEAD SCREW J-BOX FIG. 5 CROSS BAR CROSS BAR 45° TRACK UNIT LONGITUDINAL TRACK OUTLET BOX OUTLET BOX MOUNTING HOLE FIG. 1