Lightware HDMI-3D-OPT-TX210RAK Manuals

Quick Start Guide HDMI-3D-OPT-TX210A HDMI-3D-OPT-TX210RAK Further information The document is valid with the following firmware version: 1.1.0 The product brief and further information are available at www.lightware.eu. See the Downloads section on the website of the product. Contact us [email protected] +36 1 255 3800 [email protected] +36 1 255 3810 Lightware Visual Engineering LLC. Peterdy 15, Budapest H-1071, Hungary Doc. ver.: 1.1 19200060 LASER ACTIVE LIVE FIBER LINK RS-232 LASER ACTIVE LIVE FIBER LINK RS-232 LASER ACTIVE LIVE FIBER LINK RS-232 LASER ACTIVE LIVE FIBER LINK RS-232 HDMI-3D-OPT series transmitter Power adaptor Touch panel Power OPTM Local monitor HDMI RS-232 PC � � � � � Media player Blu-ray player Audio USB Compatible receiver MP3 player HDMI Audio 2 1 USB SHOW ME AUDIO SELECT VIDEO AUDIO HDCP AUDIO1 RST AUDIO2 AUDIO1 IN HDMI IN 2 1 USB SHOW ME AUDIO SELECT VIDEO AUDIO HDCP AUDIO1 RST AUDIO2 AUDIO1 IN HDMI IN 1 2 3 4 56 7 8 1 2 3 4 5 6 Safety and Warranty Info Quick Start Guide Important Safety Instructions Please read and keep the information in the attached safety instructions supplied with the product before you start using the device.  The transmitter is a Class 3R laser product. Caution! Invisible Class 3R laser radiation! Avoid exposure to the beam! Introduction Thank You for choosing Lightware HDMI-3D-OPT series transmitter. The product is a multi- mode single fiber extender with bidirectional RS-232 extension. The device transmits HDMI digital video signals up to 4K resolution, 3D- and HDCP compliant and is able to embed analog audio from 3.5mm jack or 5-pole Phoenix type ports. The HDMI-3D-OPT-TX210RAK model is built with USB KVM function. Rear View Front View 4 Audio1 input 3.5 mm jack connector for unbalanced analog audio input signal. 5 Reset button Pushing the button reboots the unit. 6 Audio select button Button for switching between audio sources. 7 Audio2 status LED LED gives feedback about actual connection status of Audio2 input port (on the rear side of device). 8 Show me button Special functions are available with this button (switch to bootload mode, restore factory default settings). 1 HDCP status LED LED shows the actual HDCP status of the video output. 2 USB port USB interface for USB KVM function, firmware upgrade, and LDC software control purposes. 3 HDMI input Connect an HDMI cable between the HDMI source and the transmitter unit. 1 SC fiber output Connect a multi-mode single fiber optical cable between the receiver and the transmitter. 2 Audio2 input 5-pole Phoenix connector for balanced analog audio input. 3 HDMI output Connect an HDMI cable between the transmitter and the display device. 4 Status LEDs LEDs give feedback about actual status of unit and connection signals. 5 RS-232 3-pole Phoenix connector for serial communication. 6 5V DC input Connect the output of the supplied 5V DC power adaptor. Front Panel LEDs Video Source LEDs � ON: video source is active. � BLINKING: video source is connected but no signal is detected. Audio Source LEDs � OFF: audio source is not selected. � BLINKING: audio source is selected but no signal is detected (digital inputs only). � ON: (with short pause): audio source is selected and the port is active but not embedded to the output video stream (DVI output mode). � ON: (continuously): audio source is selected, the port is active and the audio is embedded to the output video stream (HDMI output mode). HDCP LED � OFF: video output signal is not encrypted with HDCP. � ON: video output signal is encrypted with HDCP. USB LED � OFF: USB is disconnected or there is no USB data transfer over the port. � BLINKING (green): device control mode is active. � ON (green): USB KVM: composite mode is active. � ON (yellow): USB KVM: transparent mode is active. Connecting Steps  Rear view illustration belongs to the HDMI-3D-OPT-TX210RAK model. The HDMI-3D-OPT-TX210A model has no RS-232 LED in the Status LEDs. Box Contents Transmitter unit 5V DC adaptor with interchangeable plugs Phoenix Combicon 3-pole connector Phoenix Combicon 5-pole connector Safety and warranty info, Quick Start Guide Mounting To mount the transmitter Lightware supplies optional accessories for different usage. There are two kinds of mounting kits with similar fixing method. The transmitters have two mounting holes with inner thread on the bottom side. Fasten the device by the screws enclosed to the accessory. The Under-desk double mounting kit makes it easy to mount a single device on any flat surface, e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack or four quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order mounting accessories please contact [email protected].  The transmitter is half-rack sized. Under-desk double mounting kit 1U high rack shelf Rear Panel LEDs LIVE � OFF: device is not powered. � BLINKING (green): device is powered and operational. � BLINKING (red): alert detected. � BLINKING (yellow): firmware upgrade mode, device is in bootload mode. � ON (yellow): device is powered but no operation. LASER ACTIVE � ON (red): laser transmission is enabled. FIBER LINK � OFF: no fiber link between transmitter and receiver. � ON: fiber link is established. RS-232 (only in case of HDMI-3D-OPT-TX210RAK model) � OFF: RS-232 ports (local and link) are in Pass-through mode. � ON: RS-232 ports (local and link) are in Control mode. OPTM Connect the transmitter and the compatible receiver or matrix input board using a multimode single fiber optical cable. HDMI Connect the source (e.g. Blu-ray player) to the input port of the transmitter by a HDMI cable. Audio Optionally connect an assymmetric audio device with unbalanced audio signal (e.g. an MP3 player) to the 2.5” TRS (jack) audio input port. Audio Optionally connect a symmetric audio device with balanced audio signal (e.g. a professional media player) to the 5-pole Phoenix audio input port. HDMI Connect the local sink device (e.g. a monitor) to the HDMI output port by an HDMI cable. USB Optionally for USB HID extension: connect the transmitter to the computer by the USB mini B-type cable. * RS-232 Optionally for RS-232 control: connect a controller/controlled device (e.g. a touch panel) to the RS-232 port. Power Connect the power adaptor to the DC input on the transmitter first, then to the AC power socket. * Only HDMI-3D-OPT-TX210RAK model has built with USB KVM function. The USB interface can be used for control purpose only in case of HDMI-3D-OPT-TX210A model. Single fiber multimode optical cable up to 2500m 5V DC Power adaptor HDMI-3D-OPT-TX210RAK PC PIN: 2.1mm RS-232 TX RX LIVE LASER ACTIVE FIBER LINK RS-232 12V 1A DC HDMI OUT SC MM LASER APERTURE OUTPUT 6 AUDIO2 IN HDMI-3D-OPT-TX210RAK RS-232 A A A A HID A O <= mW CLASSIFIED B A HDMI USB Monitor Mouse Keyboard HDMI-3D-OPT-RX150RA Audio amplifier HDMI RS-232 Analog audio USB USB 5V DC Power adaptor Laptop Projector 5V DC Power adaptor HDMI-3D-OPT-TX210A PIN: 2.1mm RS-232 TX RX LIVE LASER ACTIVE FIBER LINK RS-232 12V 1A DC HDMI OUT SC MM LASER APERTURE OUTPUT 6 AUDIO2 IN A A A A HID A O <= mW CLASSIFIED B A HDMI-3D-OPT-RX150RA Audio amplifier 5V DC Power adaptor HDMI HDMI RS-232 Analog audio USB Single fiber multimode optical cable up to 2500m Audio Cable Wiring Guide HDMI-3D-OPT series transmitters are built with 5-pole Phoenix input connector. See below a few examples of the most common assembling cases. From balanced output to balanced input 2 x 6.3 (1/4”) TRS - Phoenix From balanced output to balanced input 2 x XLR - Phoenix 2 3 1 2 3 AUDIO Input From unbalanced output to balanced input 3.5 (1/8”) TRS - Phoenix From unbalanced output to balanced input 2 x RCA - Phoenix For more information about audio cable wiring see the user’s manual of the device or the Audio Cable Wiring Guide on our website www.lightware.eu. HDMI in Analog audio in 1 Analog audio in 2 Analog audio Digital audio/video Analog audio Digital audio A/D converter Digital audio Digital audio Digital video HDMI out A/D converter Embedder 3:1 digital audio switch Digital audio Fiber optical out USB HDMI splitter De-embedder Digital audio and video Processor USB control / USB KVM * RS-232 RS-232 * and USB * INPUT OUTPUT HDMI Analog audio RS-232 * USB * OPT HDMI Analog audio RS-232 * USB * + Local HDMI output + Local USB + Local RS-232 2 1 USB SHOW ME AUDIO SELECT VIDEO AUDIO HDCP AUDIO1 RST AUDIO2 AUDIO1 IN HDMI IN * Only in case of HDMI-3D-OPT-TX210RAK model. Port Diagram Software Control – Using Lightware Device Controller (LDC) The device can be controlled from a computer through the USB or RS-232 ports using Lightware Device Controller. Please download the application from www.lightware.eu, install on a Windows PC or a Mac OS X and connect to the device. Fiber Optical Output Settings ON: high-speed (AV signal) and low-speed (serial and/or USB) communication are transmitted. STANDBY: only low-speed (serial and/or USB) communication is transmitted. Restore Factory Default Settings 1. Keep the Show Me button pressed for 10 seconds, the LEDs start to blink faster. 2. Release the button, then press it 3 times quickly; factory default settings are restored: Crosspoint setting (Video/Audio) HDMI input SC laser output Enabled Emulated EDID Dynamic RS-232 mode Pass-through RS-232 control protocol LW2 RS-232 port setting 57600 BAUD, 8, N, 1 Typical application HDMI-3D-OPT-TX210A Typical application HDMI-3D-OPT-TX210RAK Model Comparison Optical interface Serial communication USB KVM HDMI-3D-OPT-TX210A Control mode - HDMI-3D-OPT-TX210RAK Control mode / Pass-through mode Yes  AV signal is always transmitted on fiber optical interface. Maximum Fiber Cable Extension Distances OM1 OM2 OM3 OM4 (62.5/125) (50/125) (50/125) (50/125) 1080p@60Hz 24 bpp 250 m 600 m 1200 m 2500 m 1080p@60Hz 36 bpp 150 m 400 m 800 m 1300 m 4096x2048@30Hz 24 bpp Not supported 350 m 700 m 1100 m USB KVM Function HDMI-3D-OPT-TX210RAK transmitter supports HID-compliant (Human Interface Device) devices to transmit USB signal between the source and sink devices. The transmitter connects to the controlled device (e.g. PC) and the controlling devices (e.g. computer mouse, keyboard, touch panel) are connected to the receiver. USB KVM function can be used in two different modes: Transparent and Composite mode. Transparent mode Composite mode Device support Supports all HID-compliant devices. Supports the following HID- compliant devices: computer mouse, keyboard built with up to 107 keys with or without specific multimedia keys. Driver software Driver for all connected USB devices has to be installed on the controlled computer. No driver is needed for the connected devices.  Only HDMI-3D-OPT-TX210RAK model is built with USB KVM function. Optical Extender Concept HDMI-3D-OPT series transmitters have a multi-mode single fiber output interface which is able to transmit different type of signals at the same time. The device accepts digital video (HDMI) and analog audio sources (jack and 5-pole Phoenix). The analog audio signal can be embedded to the digital A/V output. The unit can be controlled over RS-232 (3-pole Phoenix) and USB interfaces. Besides of these the HDMI-3D-OPT-TX210RAK model has USB KVM function.  One audio (original embedded or analog) and one video signals can be transmitted via the optical output at the same time. * Only in case of HDMI-3D-OPT-TX210RAK model. Compatible Devices The transmitter is compatible with the following receivers and input boards: � HDMI-3D-OPT-RX150RA � MX modular frames with MX-DVI-OPT-IB and MX-HDMI-OPT-IB cards Locking DC Plug Twist 90° clockwise to lock.

Quick Start Guide HDMI-3D-OPT-TX210A HDMI-3D-OPT-TX210RAK Further information The document is valid with the following firmware version: 1.0.0 The product brief and further information are available on www.lightware.eu. See the Downloads section on the website of the product. Contact us [email protected] +36 1 255 3800 [email protected] +36 1 255 3810 Lightware Visual Engineering LLC. Peterdy 15, Budapest H-1071, Hungary Doc. ver.: 1.0 19200034 Safety and warranty info Quick Start Guide 1 2 3 4 56 7 8 1 2 3 4 5 6 Power Adaptor Touch panel Local sink Laptop HDMI Transmitter Compatible receiver or input board Optical cable HDMI RS-232 1 2 3 5 4 INPUT OUTPUT HDMI RS-232 Analog OPT audio HDMI RS-232 Analog audio + Local USB + Local HDMI out Important safety instructions Please read and keep the information in the attached safety instructions supplied with the product before you start using the device. Introduction Thank You for choosing Lightware HDMI-3D-OPT-TX200 series transmitter. The product is a multi-mode single fiber extender with bi-directional RS-232 extension. The device transmits HDMI digital video signals up to 4K resolution, 3D- and HDCP compliant and is able to embed analog audio from 3.5mm jack or 5-pole Phoenix type ports. Box contents Transmitter unit 5V DC adaptor with interchangeable plugs Phoenix Combicon 3-pole connector Phoenix Combicon 5-pole connector Safety and warranty info, Quick Start Guide Rear view Front view 4 Audio1 input 3.5 mm Jack connector for asymmetric analog audio input signal. 5 Reset button Pushing the button reboots the unit. 6 Audio select button Button for switching between audio sources. 7 Audio2 status LED LED gives feedback about actual connection status of Audio2 input port (on the rear side of device). 8 Show me button Special functions are available with this button (switch to bootload mode, restore factory default settings). 1 HDCP status LED LED shows the actual HDCP status of the video source. 2 USB port USB interface for firmware upgrade and LDC connection. 3 HDMI input Connect an HDMI cable between the HDMI source and the transmitter unit. 1 SC fiber output Connect a multi-mode single fiber optical cable between the receiver and the transmitter. 2 Audio2 input 5-pole Phoenix connector for balanced analog audio input. 3 HDMI output Connect an HDMI cable between the transmitter and the display device. 4 Status LEDs LEDs give feedback about actual status of unit and connection signals. 5 RS-232 3-pole Phoenix connector for serial communication. 6 DC 5V input Connect the output of the supplied 5V DC power adaptor. Front panel LEDs Video sources � ON: video source is active. � BLINKING: video source is connected but no signal is detected. Audio sources � OFF: audio source is not selected. � BLINKING: audio source is selected but no signal is detected (digital inputs only). � ON: (with short pause): audio source is selected and the port is active but not embedded to the output video stream (DVI output mode). � ON: (continuously): audio source is selected, the port is active and the audio is embedded to the output video stream (HDMI output mode).  A port is active if there is a valid signal on it. HDCP LED � OFF: video output signal is not encrypted with HDCP. � ON: video output signal is encrypted with HDCP. USB LED � OFF: USB is disconnected. � ON (yellow): connection is established between the transmitter and the computer. Rear panel LEDs LIVE � OFF: device is not powered. � BLINKING (green): device is powered and operational. � BLINKING (red): alert detected. � BLINKING (yellow, fast): firmware upgrade mode, device is in bootload mode. � ON (yellow): device is powered but no operation. LASER ACTIVE � ON (red): laser transmission is enabled. FIBER LINK � OFF: no fiber link between transmitter and receiver. � ON: fiber link is established. RS-232 (for HDMI-3D-OPT-TX210RAK only) � OFF: RS-232 ports (local and link) are in Pass-through mode. � ON: RS-232 ports (local and link) are in Control mode. Connecting steps 1 Connect the transmitter and the receiver by a multimode optical cable via the SC fiber connectors. 2 Connect the desired source(s) to the input port(s) of the transmitter. 3 Optionally for RS-232 extension: connect a controller/controlled device (e.g. touch panel) to the RS-232 port. 4 Optionally connect a local sink to the HDMI output port. 5 Firstly connect the power adaptor to the DC input on the transmitter, then to the AC power socket. Mounting To mount the transmitter Lightware supplies optional accessories for different usage. There are two kinds of mounting kits with similar fixing method. The transmitters have two mounting holes with inner thread on the bottom side. Fasten the device by the screws enclosed to the accessory. Locking DC plug Twist 90° clockwise to lock. The Under-desk double mounting kit makes easy to mount a single device on any flat surface, e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack or four quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order mounting accessories please contact [email protected].  The transmitter is half-rack sized. Under-desk double mounting kit Part no: 5240 0276 1U high rack shelf Part no: 5240 0935 Optical extender concept HDMI-3D-OPT-TX200 series have a multi-mode single fiber output interface which is able to transmit different type of signals at the same time. On the input side video interface (HDMI), analog audio ports (jack and Phoenix) and RS-232 signal can be attached to the device. These ports can be transmitted together via the fiber optical link. Besides that a local USB, and local HDMI out ports are present. Compatible devices The transmitter is compatible with the following receivers and input boards: � HDMI-3D-OPT-RX150RA � MX modular frames with MX-DVI-OPT-IB and MX-HDMI-OPT-IB cards  Rear view illustration belongs to the HDMI-3D-OPT-TX210RAK model, TX210A is slightly different on the status LEDs. Laptop Projector 5V DC Power adaptor HDMI-3D-OPT-TX210A PIN: 2.1mm RS-232 TX RX LIVE LASER ACTIVE FIBER LINK RS-232 12V 1A DC HDMI OUT SC MM LASER APERTURE OUTPUT 6 AUDIO2 IN A A A A HID A O <= mW CLASSIFIED B A HDMI-3D-OPT-RX150RA Power amplifier 5V DC Power adaptor HDMI HDMI RS-232 Analog audio USB Single fiber multimode optical cable up to 2500m Single fiber multimode optical cable up to 2500m 5V DC Power adaptor HDMI-3D-OPT-TX210RAK PC PIN: 2.1mm RS-232 TX RX LIVE LASER ACTIVE FIBER LINK RS-232 12V 1A DC HDMI OUT SC MM LASER APERTURE OUTPUT 6 AUDIO2 IN HDMI-3D-OPT-TX210RAK RS-232 A A A A HID A O <= mW CLASSIFIED B A HDMI USB Monitor Mouse Keyboard HDMI-3D-OPT-RX150RA Power amplifier HDMI RS-232 Analog audio USB USB 5V DC Power adaptor Software control – Using Lightware Device Controller (LDC) The device can be controlled from a computer through the USB or RS-232 ports using Lightware Device Controller. Please download the application from www.lightware.eu, install on a Windows PC or a Mac OS X and connect to the device. Restore factory default settings 1. Keep the Show me button pressed for 10 seconds, the LEDs start to blink faster. 2. Release the button, then press it 3 times quickly; factory default settings are restored: Crosspoint setting (Video/Audio) HDMI input SC laser output Enabled Emulated EDID Dynamic RS-232 mode Passthrough RS-232 control protocol LW2 RS-232 port setting 57600 BAUD, 8, N, 1 Typical application HDMI-3D-OPT-TX210A Typical application HDMI-3D-OPT-TX210RAK Model comparison Optical interface Serial communication USB KVM HDMI-3D-OPT-TX210A CT - HDMI-3D-OPT-TX210RAK CT / PT Yes * CT = Control mode, PT = Pass-through mode * USB KVM function is under development, it will be added by firmware upgrade.  AV signal is always transmitted on fiber optical interface. Fiber optical output settings ON: high-speed (AV signal) and low-speed (serial) communication are transmitted. STANDBY: only low-speed (serial) communication is transmitted. Firmware upgrade Lightware Device Updater (LDU) is an easy and comfortable way to keep your device up-to-date. Steps of firmware upgrading are the following: 1. Download and install LDU software from the company’s website www.lightware.eu. 2. Get the latest firmware package from Lightware Support ([email protected]). 3. Establish the connection between the extender and the computer with a mini-USB cable. 4. Start LDU software and select the Extender mode. 5. Load the new firmware file. 6. Please read the Instructions related this model. 7. Select your upgradeable device. 8. Review the list of selected devices. Please check “Factory reset” option to be disabled to avoid settings loss. If you want to set all settings to default values, enable this option. 9. Start firmware upgrading. 10. Please wait until it is completed and device rebooted. 11. Ready.  In certain cases new firmware version requires a factory reset to apply all new features in the device. In this case “Factory reset” option is enabled by default and not changeable by the user. Maximum cable extension distances OM1 OM2 OM3 OM4 (62.5/125) (50/125) (50/125) (50/125) 1080p@60Hz 24 bpp 250 m 600 m 1200 m 2500 m 1080p@60Hz 36 bpp 150 m 400 m 800 m 1300 m 4096x2048@30Hz 24 bpp Not supported 350 m 700 m 1100 m

HDMI-3D-OPT-TX210A HDMI-3D-OPT-TX210RAK SW4-OPT-TX240RAK HDMI-3D-OPT-RX150RA User’s Manual Fiber Optical Multimedia Extender  HDMI-3D-OPT series – User's Manual 2 Important Safety Instructions Class II apparatus construction. The equipment should be operated only from the power source indicated on the product. To disconnect the equipment safely from power, remove the power cord from the rear of the equipment, or from the power source. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. There are no user-serviceable parts inside of the unit. Removal of the cover will expose dangerous voltages. To avoid personal injury, do not remove the cover. Do not operate the unit without the cover installed. The appliance must be safely connected to multimedia systems. Follow instructions described in this manual. Ventilation For the correct ventilation and to avoid overheating ensure enough free space around the appliance. Do not cover the appliance, let the ventilation holes free and never block or bypass the ventilators (if any). WARNING To prevent injury, the apparatus is recommended to securely attach to the floor/wall or mount in accordance with the installation instructions. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. Waste Electrical & Electronic Equipment WEEE This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. Caution: Laser product INVISIBLE LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT Radiated wavelenght: 778 nm, 800 nm, 825 nm, 850 nm, 911 nm, 980 nm Output power <= 1 mW Classified by EN 60825-1:2007 Common Safety Symbols Symbol Description Direct current Alternating current Double insulation  Caution, possibility of eletric shock Caution Laser radiation     HDMI-3D-OPT series – User's Manual 3 Symbol Legend The following symbols and markings are used in the document: WARNING! Safety-related information which is highly recommended to read and keep in every case! ATTENTION! Useful information to perform a successful procedure; it is recommended to read. INFO: A notice which may contain additional information. Procedure can be successful without reading it. DEFINITION: The short description of a feature or a function. TIPS AND TRICKS: Ideas which you may have not known yet but can be useful. Navigation Buttons Go back to the previous page. If you clicked on a link peviously, you can go back to the source page by clicking the button. Navigate to the Table of Contents. Step back one page. Step forward to the next page.     Document Information This User’s Manual applies to the following versions of the mentioned software, firmware, and hardware: Item Version Lightware Device Controller (LDC) software 1.18.0b6 Lightware Device Updater (LDU) software 1.5.0b8 Controller firmware - Transmitters 1.1.0 Controller firmware - Receiver 2.0.0 Hardware - Transmitters 1.1 Hardware - Receiver 1.3 Document revision: 2.1 Release date: 31-10-2018 Editor: Laszlo Zsedenyi     HDMI-3D-OPT series – User's Manual 4 1. INTRODUCTION....................................................................................7 1.1. Description....................................................................................7 1.2. Box Contents................................................................................7 1.3. Compatible Devices.......................................................................7 1.4. Features........................................................................................8 1.5. Model Comparison of the Transmitters......................................8 1.6. Typical Application......................................................................8 2. INSTALLATION....................................................................................10 2.1. Mounting Options.......................................................................10 2.1.1. 1U High Rack Shelf.......................................................................... 10 2.1.2. Under-desk Mounting Kit................................................................ 10 2.1.3. Under-desk Double Mounting Kit.................................................... 10 2.2. Connecting Steps........................................................................11 2.2.1. Receiver............................................................................................ 11 2.2.2. Transmitter....................................................................................... 11 3. PRODUCT OVERVIEW.......................................................................12 3.1. Front View - Transmitter...........................................................12 3.2. Rear View - Transmitter.............................................................13 3.3. Front and Rear View - Receiver..................................................13 3.4. Electrical Connections..............................................................13 3.4.1. 5V DC Connection........................................................................... 13 3.4.2. HDMI Connector.............................................................................. 14 3.4.3. DVI-I Connector................................................................................ 14 3.4.4. DisplayPort Connector.................................................................... 14 3.4.5. SC Fiber Optical Connector............................................................. 14 3.4.6. Analog Stereo Audio Connector (3.5 mm Jack)............................ 14 3.4.7. Analog Stereo Audio Connector (5-pole Phoenix)......................... 14 3.4.8. S/PDIF Connector............................................................................ 14 3.4.9. RS-232 Connector (3-pole Phoenix)............................................... 14 3.4.10. RS-232 Connector (D-sub)............................................................ 14 3.4.11. Ethernet Connector....................................................................... 15 3.4.12. USB Mini Connector...................................................................... 15 3.4.13. USB Connector for KVM................................................................ 15 3.4.14. GPIO - General Purpose Input/Output Ports................................ 15 3.5. Optical Extender Concept..........................................................15 3.5.1. Transmitter....................................................................................... 15 3.5.2. Receiver............................................................................................ 16 3.6. Port Diagrams............................................................................16 3.7. Audio Interface...........................................................................17 3.7.1. Audio Inputs and Modes - Transmitter........................................... 17 3.7.2. Audio Outputs and Modes - Receiver............................................. 17 3.7.3. Audio Options - Example................................................................. 18 3.8. Video Interface...........................................................................18 3.9. The Autoselect Feature..............................................................18 3.10. USB KVM Function....................................................................19 3.11. Controlling Features...............................................................20 3.11.1. Serial Interface.............................................................................. 20 3.11.2. GPIO Interface............................................................................... 21 3.11.3. USB Control Interface.................................................................... 22 3.11.4. Ethernet Control Interface............................................................ 22 3.12. Further Built-in Features........................................................22 3.12.1. Automatically Launched Actions - The Event Manager.............. 22 3.12.2. Advanced EDID Management....................................................... 22 3.12.3. Extender Cloning – Configuration Backup and Restore............. 22 4. OPERATION........................................................................................23 4.1. Front Panel LEDs - Transmitter................................................23 4.1.1. Video Input LEDs............................................................................. 23 4.1.2. Audio Input LEDs............................................................................. 23 4.1.3. HDCP LED........................................................................................ 23 4.1.4. USB LED........................................................................................... 23 4.1.5. Autoselect LED................................................................................ 23 4.2. Front Panel Buttons - Transmitter..........................................23 4.2.1. Video Select Button......................................................................... 23 4.2.2. Audio Select Button......................................................................... 24 4.2.3. Programmable Show Me Button.................................................... 24 4.3. Special Functions - Transmitter................................................24 4.3.1. Enable DHCP (Dynamic) IP Address.............................................. 24 4.3.2. Reset to Factory Default Settings................................................... 24 4.3.3. Control Lock..................................................................................... 24 4.3.4. Reseting the Device......................................................................... 24 4.3.5. Entering Firmware Upgrade Mode.................................................. 24 4.4. Rear Panel Status LEDs - Transmitter......................................24 4.4.1. LIVE LED........................................................................................... 24 4.4.2. LASER ACTIVE LED......................................................................... 24 4.4.3. FIBER LINK LED............................................................................... 25 4.4.4. RS-232 LED...................................................................................... 25 4.5. Front Panel LEDs - Receiver.......................................................25 4.5.1. POWER LED..................................................................................... 25 4.5.2. Status LEDs...................................................................................... 25 4.6. Special Functions - Receiver......................................................25 4.6.1. Reset to Factory Default Settings................................................... 25 4.6.2. Entering Firmware Upgrade Mode.................................................. 25 4.7. Software Control Modes...........................................................26 5. SOFTWARE CONTROL - LIGHTWARE DEVICE CONTROLLER.....27 5.1. Install and Upgrade...................................................................27 5.2. Establishing the Connection......................................................27 5.3. Crosspoint / Port Control Menu...............................................28 5.4. Port Properties Windows...........................................................29 5.4.1. Video Inputs..................................................................................... 29 5.4.2. Digital Audio Inputs......................................................................... 29 5.4.3. Analog Audio Inputs........................................................................ 30 5.4.4. Video Outputs.................................................................................. 30 5.4.5. Digital Audio Outputs...................................................................... 31 5.4.6. Analog Audio Output....................................................................... 31 5.5. Diagnostic Tools.........................................................................31 5.5.1. Frame Detector................................................................................ 31 5.5.2. No Sync Screen (Test Pattern)....................................................... 32 5.6. USB KVM......................................................................................32 5.6.1. USB KVM in the Receiver................................................................ 32 5.6.2. USB KVM in the Transmitter........................................................... 32 5.7. EDID Menu....................................................................................33 5.7.1. EDID Operations.............................................................................. 33 5.7.2. EDID Summary Window.................................................................. 34 5.7.3. Editing an EDID................................................................................ 34 5.7.4. Creating an EDID - Easy EDID Creator............................................ 35 5.8. Control / Device Control Menu.................................................35 5.8.1. RS-232.............................................................................................. 35 5.8.2. GPIO................................................................................................. 36 5.8.3. Ethernet............................................................................................ 36 5.9. Event Manager............................................................................37 5.9.1. Create or Modify an Event............................................................... 38 5.9.2. Special Tools and Accessories....................................................... 38 5.9.3. Clear One or More Event(s)............................................................. 39 5.9.4. Export and Import Events............................................................... 39 5.9.5. Event Creating - Example................................................................ 39 5.10. Settings Menu...........................................................................40 5.10.1. Status............................................................................................. 40 5.10.2. Network.......................................................................................... 40 5.10.3. Backup........................................................................................... 40 5.10.4. System........................................................................................... 41 5.11. Configuration Cloning (Backup Tab)........................................41 5.11.1. Steps in a Nutshell........................................................................ 41 5.11.2. Save the Settings of a Device (Backup)....................................... 42 5.11.3. Upload the Settings to a Device (Restore)................................... 42 5.12. Advanced View Window.............................................................42 Table of Contents   

HDMI-3D-OPT-TX210A HDMI-3D-OPT-TX210RAK SW4-OPT-TX240RAK User’s manual SAFETY INSTRUCTIONS Class II apparatus construction. The equipment should be operated only from the power source indicated on the product. To disconnect the equipment safely from power, remove the power cord from the rear of the equipment, or from the power source. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. There are no user-serviceable parts inside of the unit. Removal of the cover will expose dangerous voltages. To avoid personal injury, do not remove the cover. Do not operate the unit without the cover installed. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. The appliance must be safely connected to multimedia systems. Follow instructions described in this manual. Ventilation For the correct ventilation and avoid overheating ensure enough free space around the appliance. Do not cover the appliance, let the ventilation holes free and never block or bypass the ventilators (if any). WARNING To prevent injury, the apparatus is recommended to securely attach to the floor/wall or mount in accordance with the installation instructions. WEEE ( Waste Electrical & Electronic Equipment ) Correct Disposal of This Product This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. Caution: Laser product INVISIBLE LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT Radiated wavelengths: 778nm, 800nm, 825nm, 850nm, 911nm Output power <= 5mW Classified by EN 60825-1:2014 HDMI-3D-OPT-TX200 series User’s manual Safety instructions Page 3 / 106