LORUS RW6 Series Manuals

S3 ■ CHARACTERISTICS 1. Analogue & digital time displays: Hour, Minute, Second, Month, Date and Day of the week. 2. Daily alarm and hourly chime: The alarm can be set to sound at the designated time on a 24-hour basis and the chime can be set to sound every hour on the hour with a single beep. 3. Stopwatch: The stopwatch can measure up to 23 hours 59 minutes and 59 seconds i n 1 / 1 0 0 - s e c o n d i n c re m e n t s . S p l i t t i m e measurement is available. 4. Selection of 12 or 24-hour format: The time display format in either 12-hour indication or 24-hour indication can be selected. 5. EL backlight: The built-in electro-luminescent (EL) backlight illuminates the display for easy viewing in darkness. ■ DISPL AY AND BUT TON FUNCTION ■ HOW TO SET TIME/CALENDAR ■ HOW TO SET AL ARM TIME ■ HOW TO CHANGE THE DISPL AY MODE ■ SET TING THE TIME (ANALOGUE) 1. Pull the crown out one step, the second hand will stop. 2. Set the correct time by turning the crown. 3. Push the crown back to the original position. The watch will start running again. * The analogue indication and digital display of the time setting can be adjusted separately. STOPWATCH mode 1. From NORMAL TIME mode, press S3 button twice to enter the ALARM mode. 2. Press S2 button to begin setting procedure. The hours digit starts flashing. 3. Press S1 button to set HOURS setting. 4. Press S2 button to move on to MINUTES setting. Press S1 button to set MINUTES setting. 5. Press S2 button to confirm the settings. 6. Press S3 button to return to NORMAL TIME mode. * Press S3 button to show the NORMAL TIME mode. * If the NORMAL TIME mode is shown already on the display, skip the above operation. * Press S3 button to change the display mode in the following order. NREZ021 3-2013 CAL. Z021 (RW6 SERIES) 1. From NORMAL TIME mode, press S3 button three times to begin setting procedure. The second digits start flashing. 2. Press S1 button to reset the second digits to zero. * If S1 button is pressed when the second digits are in a range between 30 and 59, the second digits will be reset to 00 and one minute will be added. If S1 button is pressed when the second digits are in a range between 00 and 29, the second digits will be reset to 00 and the minute digits will be unchanged. 3. Press S2 button to move on to HOURS setting. * Selection of the digits to be adjusted is made in the following order by pressing S2 button. Press S1 button to adjust the value. * When setting HOURS, “H” stands for 24-hour format, “A” or “P” stands for 12-hour format. 4. Press S3 button after completing the setting. CROWN NORMAL TIME mode S3 ALARM mode S3 S3 S2 HOURS SETTING BY PRESSING S1 MINUTES SETTING BY PRESSING S1 S2 NORMAL TIME MINUTES SETTING BY PRESSING S1 HOURS SETTING BY PRESSING S1 SECONDS SETTING BY PRESSING S1 PRESS S3 3 times S2 S2 MONTH SETTING BY PRESSING S1 DATE SETTING BY PRESSING S1 S3 SECONDS DATE DAY OF THE WEEK MONTH MINUTES HOURS S2 S2 S2 S2 S2 12/24H- FORMAT S2 TIME SETTING mode ALARM mode NORMAL TIME mode S2 DAY OF WEEK SETTING BY PRESSING S1 S2 S3 S4 (LIGHT) HOURS DAY OF WEEK CHIME DATE MINUTES SECONDS ALARM S3 (MODE) S2 (RESET) MONTH S1(STAR T/STOP) S2 S2 PRESS S3 twice S2 for confirmation Engagement/Disengagement of ALARM & CHIME * In the ALARM setting mode, with each press of S1 button, the ALARM and CHIME can be engaged or disengaged in the following order. The ALARM signal and/or CHIME signal appear or disappear on the display accordingly. S1 S1 S3 NORMAL TIME S1 ALARM ON CHIME ON ALARM/CHIME ON S1 ALARM MODE How to stop the alarm sound Press S3 to turn the snooze function on or off alternately. When the snooze function is enabled, the alarm will stop sounding temporarily and go off again 5 minutes later for 20 seconds and automatically stop. Press S1 or S2 to stop the alarm while it is sounding. Snooze function PRESS S3 twice all-guides .com