LORUS W150 Manuals

I CHARACTERISTICS 1. Time and calendar: •Hour, minutes, seconds, year, month, date and day of the week. • Fully automatic calendar: The calendar adjusts automatically for odd and even months including February of leap years from the year 1996 up to 2045 (Cal. W150) or 2000 up to 2049 (Cal. W151). • Time indication: Changeover between 12- and 24-hour indications is possible. 2. Stopwatch: Measures up to 23 hours, 59 minutes and 59 seconds in 1/100-second increments for the first hour and in 1-second increments thereafter. 3. 75 lap/split memory (Cal. W150) or 100 lap/split memory (Cal. W151): Up to 75 sets (Cal. W150) or 100 sets (Cal. W151) of lap times and split times can be stored in memory. 4. Countdown timer: Up to 23 hours, 59 minutes and 59 seconds can be set in second increments. •After the set time is up, the timer counts up the time up to 23 hours, 59 minutes and 59 seconds. •The set time can be used repeatedly unless canceled. 5. Daily alarm: The alarm can be set to ring on a 24-hour basis. • Hourly time signal: Can be set to ring every hour on the hour with a single beep. 6. Illuminating light: The light evenly illuminates the display for easy viewing in the dark. START STOP L A P 75LAP MEMORY WATER 50M RESIST Day I BUTTONS AND DISPLAYS Hour A Date Seconds Minutes C D B PM mark Light button * If the stopwatch is measuring and button “A” is pressed to change the mode from the STOPWATCH, the TIMER mode appears, skipping the MEMORY RECALL mode. With each press of button “A”, the selection of the mode can be made in the following order: STOPWATCH mode TIME/CALENDAR mode ➡ ➡ ➡ ➡ ➡ TIMER mode A A A A A ALARM mode MEMORY RECALL mode Day B A C D PM mark Month Year Date → → → → Date Seconds Minutes Hour I TIME/CALENDAR MODE 1. Press button “A” to show the TIME/CALENDAR mode. 2. Press button “B” for 2 to 3 seconds to show the time/calendar setting display. The second digits start flashing. 3. Selection of the digits to be adjusted (flashing) is made in the following order by pressing button “C”. 4. Press button “D” to set the flashing digits. One digit is advanced with each press of the button. Digits except seconds move quickly by keeping button “D” pressed. Hour Minutes Seconds → → G 12-/24-hour indication setting Changeover between 12- and 24-hour indications is made alternately with each press of button “A”. G Seconds setting Press button “D” in accordance with a time signal. The seconds are reset to “00” and start immediately. When the seconds count any number from “30” to “59” and button “D” is pressed, one minute is added and the seconds are reset to “00”. 5. After all the adjustments are completed, press button “B” to return to the TIME/ CALENDAR mode. Notes: 1. When setting the hour digits in the 12-hour indication, check that AM/PM is set properly. Only “PM” mark is displayed. For the AM setting, there is no indication. In the 24-hour indication, “24” is displayed. 2. Once the year, month and date have been set, the day of the week is set automatically. 3. If the watch is left untouched in the time/ calendar setting display with the digits flashing, it will automatically return to the TIME/ CALENDAR mode in 1 to 2 minutes. I STOPWATCH MODE • The stopwatch can measure up to 23 hours, 59 minutes and 59 seconds. • It measures in 1/100-second increments for the first hour and in 1-second increments thereafter. Stopwatch operation Press button “A” to show the STOPWATCH mode. “Chrono” is displayed first, and then the STOPWATCH mode appears. C A D B Standard measurement D Start D Stop C Reset D Start D Stop D Restart D Stop C Reset ** Restart and stop of the stopwatch can be repeated by pressing button “D”. ** Accumulated elapsed time measurement Lap time/split time measurement • A “Start-Finish-End” stopwatch operation system is used. The data obtained from the start till finish of a race is recorded as a block and stored in memory. D C Lap time Split time B A Notes: 1. Up to 75 (Cal. W150) or 100 (Cal. W151) measurements can be stored in memory. If more than 75 / 100 measurements are made, the measurements over 75 / 100 will not be stored in memory. 2. When the memory has become full and a lap time/split time measurement is made, “FULL” appears below the measured lap time, indicating that the measurement data is not stored in memory. To check the memory capacity, change the mode to the MEMORY RECALL mode, which displays the number of storable data. 3. If the lap time measurement exceeds 60 minutes, any fraction less than a second will be discarded when it is displayed. The split time recalled in the MEMORY RECALL mode, which is the accumulation of the actual lap time measurements, therefore, may not be exactly equal to the one displayed when it was measured. D C C C Start Lap/ split 1 Lap/ split 2 ** Finish (Final lap/split) D End C Reset * Lap time measured remains displayed for 5 seconds in the upper row. In the lower row, the lap number is displayed, followed by split time measured. Then, the measurement in progress appears. * The time elapsed from the finish of the race until the end of the measurement will not be included in the measurement. ** Lap time/split time can be measured repeatedly by pressing button “C”. I MEMORY RECALL MODE • Up to 75 sets (Cal. W150) or 100 sets (Cal. W151) of lap times and split times can be stored in memory. • Measurement data obtained from the start to finish of a race is recorded as a block, to which a block number is assigned. • Up to 38 blocks (Cal. W150) or 50 blocks (Cal. W151) of data can be stored in memory, and stored data can be recalled block by block after the measurement. Memory recall operation Press button “A” to show the MEMORY RECALL mode. “RECAL” is displayed first, and then the MEMORY RECALL mode appears. Number of storable data B D A C 1. Press button “C” to show the block selection display. “RUN” and the block number are displayed. 2. Press button “C” repeatedly to select the desired block of data. * With each press of the button, the block number advances by one, starting from Block 1. 3. Press button “D” to recall the stored data in the block. The lap/split number is displayed first, and then the lap time and split time are displayed in the upper and lower rows, respectively. * With each press of the button, the stored data is recalled successively from the oldest to the newest. • To erase the data block by block: In the block selection display, press button “C” to select the block of data to be erased, and then press and hold button “B” until “DEL” appears. The data only in the selected block is erased from memory. How to clear the stored data • To erase the data in all the blocks at a stretch: In the block selection display with any block number shown, press and hold button “B” until “FREE” appears. The data in all the blocks is erased from memory. Notes: 1. When a block of data is erased, the block number is reassigned accordingly. 2. When the stored data in all the blocks is erased, the mode is automatically changed to the STOPWATCH. 3. The stored data cannot be erased one by one. INSTRUCTION MANUAL CAL. W150 (RCW SERIES) CAL. W151 (RE5 SERIES) NREW151C 11-2000