Lund Latitude 26510016 Manuals

Page 1 of 5 Installation Instructions I - Sheet Number LUNDRB25 Rev.A Important Safety Information NOTE: Actual product may vary from illustration. Contents Latitude Nerf Bar for F-150 Super Crew For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. • To be used with Lund® branded products only. • Do not stand on Lund running board or bracket while vehicle is in motion. • Do not use the brackets as a jacking point for the vehicle. • Do not use the bracket system or running boards to fasten cargo. • Periodically check all components for tightness. • Be sure to wear safety glasses while installing brackets. •When using power tools, read and understand all operating instructions. Tools Required Preparation Before Installation • Park your vehicle in a clean, level location. Check to make sure the vehicle is in park, or for manual drive models, place the transmission in first gear. Engage the parking brake. Chock wheels. • Unpack the kit and identify the parts according to the content descriptions. • An assistant is recommended to help position the running board properly during the installation. Socket Set Wheel Chocks Safety Glasses Ratchet and Extension Lund Part# 26510016 26610016 Passenger Side Nerf Bar Driver Front Bracket Passenger Front Bracket Passenger Mid Bracket Passenger Rear Bracket Driver Rear Bracket Driver Mid Bracket 12mm Single Bolt Plate (2) 12mm Double Bolt Plate (2) 12mm Plastic Retainers (6) 8mm x 30 mm hex bolt (16) 8mm x 25 mm hex bolt (12) 8mm x 24mm OD x 2mm Flat Washer (36) 8mm Lock Washer (28) 8mm Hex Nut (8) 12mm flat washer (6) 12mm lock washer (6) 12mm hex nuts (6) 8mm clip nuts (8) Driver Side Nerf Bar 3 2 Page 2 of 5 1 Installation Steps NOTE: Actual application may vary slightly from illustrations. Locate the driver side front Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut. Line up the two holes in the Mounting Bracket with the previously installed Nut Clips and secure with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers. Do not tighten hardware at this time. Starting at the driver side-front of the vehicle, locate the round and rectangular openings in the inner body panel. NOTE: Mounting holes may be covered with rubber grommet and/or sealing tape. Remove to uncover mounting locations. Insert (2) 8mm Clip Nuts, (with the nut portion to the inside), into the rectangular opening and line up the threaded nut with the factory round holes. Next, partially thread (1) 12mm Plastic Retainer onto (1) 12mm Bolt Plate, and insert the Bolt Plate into the large round hole. Once inserted, thread the Plastic Retainer onto the Bolt Plate until it is tight against the body panel. NOTE: When properly installed, the Plastic Retainer is designed to prevent the Bolt Plate from falling into the body cavity during Bracket installation. (Figure 1). Align the clip nuts with the two round holes Remove the rubber grommet / sealing tape covering this hole Bolt Plate Plastic Retainer Figure 1 Figure 2 Figure 3 Front Front Front Line up the two holes in the bottom of the Mounting Bracket with the factory holes in the pinch weld. Attach the Mounting Bracket to the pinch weld using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Flat Washers. Insert the Hex Bolt with the Flat Washer up, from the outside-in. Secure with (2) 8mm Flat Washers, (2) 8mm Flat Washers, and (2) 8mm Hex Nuts, (Figure 3). Snug all hardware but do not tighten at this time. (1) 12mm Flat Washer (1) 12mm Lock Washer (1) 12mm Hex Nut (2) 8mm Hex Bolt (2) 8mm Flat Washer (2) 8mm Hex Bolt (2) 8mm Lock Washer (2) 8mm Flat Washer (2) 8mm Flat Washer (2) 8mm Lock Washer (2) 8mm Hex Nut Page 3 of 5 Installation Steps NOTE: Actual application may vary slightly from illustrations. 4 5 6 Figure 5 Figure 4 Figure 6 Starting at the driver side-middle of the vehicle, locate the round and rectangular openings in the inner body panel. NOTE: Mounting holes may be covered with rubber grommet and/or sealing tape. Remove to uncover mounting locations. Insert (2) 8mm Clip Nuts, (with the nut portion to the inside), into the rectangular opening and line up the threaded nut with the factory round holes. (Figure 4). Locate the driver side middle Mounting Bracket. Line up the two holes in the Mounting Bracket with the previously installed Nut Clips and secure with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers. (Figure 5) Front Line up the two holes in the bottom of the Mounting Bracket with the factory holes in the pinch weld. Attach the Mounting Bracket to the pinch weld using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Flat Washers. Insert the Hex Bolt with the Flat Washer up, from the outside-in. Secure with (2) 8mm Flat Washers, (2) 8mm Flat Washers, and (2) 8mm Hex Nuts, (Figure 3). Snug all hardware but do not tighten at this time. (2) 8mm Hex Bolt (2) 8mm Flat Washer (2) 8mm Flat Washer (2) 8mm Lock Washer (2) 8mm Hex Nut Page 4 of 5 Installation Steps NOTE: Actual application may vary slightly from illustrations. 7 8 9 10 Figure 8 Figure 7 Locate the driver side rear Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (2) 12mm Flat Washer, (2) 12mm Lock Washer and (2) 12mm Hex Nut. Do not tighten hardware at this time. Front (2) 12mm Flat Washer (2) 12mm Lock Washer (2) 12mm Hex Nut Bolt, lock washer, and flat washer Nerf bar Figure 9 Figure 10 Moving to the rear, locate the factory large round hole and smaller oval hole in the inner body panel. NOTE: Mount- ing holes may be covered with rubber grommet, insulation or sealing tape. Uncover mounting locations. Select (1) 12mm Double Bolt Plate and insert it into the larger round opening and out the smaller oval hole. Next, thread (2) 12mm Plastic Retainer onto the threaded end. Thread the Retainers all of the way down until tight against the sheet metal. (Figure 7) Align the passenger side nerf bar with the driver side front mounting bracket and loosely attach using (2) 8mm x 25mm bolts, (2) 8mm lock washers, and (2) 8mm x 24 mm flat washers. (Figure 9) Repeat Step 9 to attach the nerf bar at the middle and rear bracket locations. (Figure 10)

Page 1 of 5 Installation Instructions I - Sheet Number LUNDRB29 Rev.A Important Safety Information NOTE: Actual product may vary from illustration. Contents Latitude Nerf Bar for F-150 Super Cab For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. • To be used with Lund® branded products only. • Do not stand on Lund running board or bracket while vehicle is in motion. • Do not use the brackets as a jacking point for the vehicle. • Do not use the bracket system or running boards to fasten cargo. • Periodically check all components for tightness. • Be sure to wear safety glasses while installing brackets. •When using power tools, read and understand all operating instructions. Tools Required Preparation Before Installation • Park your vehicle in a clean, level location. Check to make sure the vehicle is in park, or for manual drive models, place the transmission in first gear. Engage the parking brake. Chock wheels. • Unpack the kit and identify the parts according to the content descriptions. • An assistant is recommended to help position the running board properly during the installation. Socket Set Wheel Chocks Safety Glasses Ratchet and Extension Lund Part# 26510017 26610017 Passenger Side Nerf Bar Driver Front Bracket Passenger Front Bracket Passenger Mid Bracket Passenger Rear Bracket Driver Rear Bracket Driver Mid Bracket 12mm Single Bolt Plate (4) 12mm Double Bolt Plate (2) 12mm Plastic Retainers (8) 8mm x 30 mm hex bolt (8) 8mm x 25 mm hex bolt (12) 8mm x 24mm OD x 2mm Flat Washer (24) 8mm Lock Washer (20) 8mm Hex Nut (4) 12mm flat washer (6) 12mm lock washer (6) 12mm hex nuts (6) 8mm clip nuts (4) Driver Side Nerf Bar Washer Plate (2) 12mm flange nut (4) 3 2 Page 2 of 5 1 Installation Steps NOTE: Actual application may vary slightly from illustrations. Locate the driver side front Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut. Line up the two holes in the Mounting Bracket with the previously installed Nut Clips and secure with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers. Do not tighten hardware at this time. (Figure 2) Starting at the driver side-front of the vehicle, locate the round and rectangular openings in the inner body panel. NOTE: Mounting holes may be covered with rubber grommet and/or sealing tape. Remove to uncover mounting locations. Insert (2) 8mm Clip Nuts, (with the nut portion to the inside), into the rectangular opening and line up the threaded nut with the factory round holes. Next, partially thread (1) 12mm Plastic Retainer onto (1) 12mm Bolt Plate, and insert the Bolt Plate into the large round hole. Once inserted, thread the Plastic Retainer onto the Bolt Plate until it is tight against the body panel. NOTE: When properly installed, the Plastic Retainer is designed to prevent the Bolt Plate from falling into the body cavity during Bracket installation. (Figure 1). Align the clip nuts with the two round holes Remove the rubber grommet / sealing tape covering this hole Bolt Plate Plastic Retainer Figure 1 Figure 2 Figure 3 Front Front Front Line up the two holes in the bottom of the Mounting Bracket with the factory holes in the pinch weld. Attach the Mounting Bracket to the pinch weld using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Flat Washers. Insert the Hex Bolt with the Flat Washer up, from the outside-in. Secure with (2) 8mm Flat Washers, (2) 8mm Flat Washers, and (2) 8mm Hex Nuts, (Figure 3). Snug all hardware but do not tighten at this time. (1) 12mm Flat Washer (1) 12mm Lock Washer (1) 12mm Hex Nut (2) 8mm Hex Bolt (2) 8mm Flat Washer (2) 8mm Hex Bolt (2) 8mm Lock Washer (2) 8mm Flat Washer (2) 8mm Flat Washer (2) 8mm Lock Washer (2) 8mm Hex Nut Page 3 of 5 Installation Steps NOTE: Actual application may vary slightly from illustrations. 6 7 4 5 Install (1) 12mm bolt plate and (1) 12mm plastic retainer. (Figure 4) Align double oval cutout in bracket over stud shown below. (Figure 5) Install middle bracket, top first. Secure with 12mm flange nut on to the bolt plate previously installed in Step 4. (Figure 6) Install washer plate over stud (Step 5), and secure with 12mm flange nut. (Figure 7) Figure 5 Figure 6 Figure 7 Figure 4 Page 4 of 5 Installation Steps NOTE: Actual application may vary slightly from illustrations. 8 9 10 11 Figure 9 Figure 8 Locate the driver side rear Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (2) 12mm Flat Washer, (2) 12mm Lock Washer and (2) 12mm Hex Nut. Do not tighten hardware at this time. (Figure 9) Front (2) 12mm Flat Washer (2) 12mm Lock Washer (2) 12mm Hex Nut Bolt, lock washer, and flat washer Nerf bar Figure 10 Figure 11 Moving to the rear, locate the factory large round hole and smaller oval hole in the inner body panel. NOTE: Mount- ing holes may be covered with rubber grommet, insulation or sealing tape. Uncover mounting locations. Select (1) 12mm Double Bolt Plate and insert it into the larger round opening and out the smaller oval hole. Next, thread (2) 12mm Plastic Retainer onto the threaded end. Thread the Retainers all of the way down until tight against the sheet metal. (Figure 8) Align the passenger side nerf bar with the driver side front mounting bracket and loosely attach using (2) 8mm x 25mm bolts, (2) 8mm lock washers, and (2) 8mm x 24 mm flat washers. (Figure 10) Repeat Step 9 to attach the nerf bar at the middle and rear bracket locations. (Figure 11)