M-system Mini-M M2PHS Manuals

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected] EM-5086 Rev.6 P. 1 / 3 INSTRUCTION MANUAL Mini-M™ PEAK HOLD MODEL M2PHS BEFORE USE .... Thank you for choosing M-System. Before use, please check contents of the package you received as outlined below. If you have any problems or questions with the product, please contact M-System’s Sales Office or representatives. ■ PACKAGE INCLUDES: Signal conditioner (body + base socket + input resistor)..................................(1) Input resistor is provided only with current input type. ■ MODEL NO. Confirm Model No. marking on the product to be exactly what you ordered. ■ INSTRUCTION MANUAL This manual describes necessary points of caution when you use this product, including installation, connection and basic maintenance procedures. POINTS OF CAUTION ■ NONINCENDIVE APPROVAL OPTION • This equipment is suitable for use in Class I, Div. 2, Groups A, B, C and D or Non-Hazardous Locations only. • WARNING! Before You Remove the Unit from Its Base Socket or Mount It, Turn Off the Power Supply and Input Signal for Safety. • WARNING! – Explosion Hazard – Substitution of Components May Impair Suitability for Class I, Div. 2. • WARNING! – Explosion Hazard – Do Not Disconnect Equipment Unless Power Has Been Switched Off or The Area is Known To Be Non-Hazardous. • The equipment was evaluated for use in the ambient tem- perature and relative humidity as mentioned in ‘ENVI- RONMENT’ section. • The input and output wiring must be in accordance with Class I, Div. 2 wiring methods and in accordance with the authority having jurisdiction for use in these hazardous locations. ■ CONFORMITY WITH EU DIRECTIVES OR UL • This equipment is suitable for Pollution Degree 2, Meas- urement Category II (input, transient voltage 2500V) and Installation Category II (transient voltage 2500V). Rein- forced insulation (signal input or output to power input: 300V) and basic insulation (signal input to output: 300V) are maintained. Prior to installation, check that the insu- lation class of this unit satisfies the system requirements. • Altitude up to 2000 meters. • The equipment must be mounted inside a panel. • The equipment must be installed such that appropriate clearance and creepage distances are maintained to con- form to CE/UL requirements. Failure to observe these requirements may invalidate the CE/UL conformance. • The actual installation environments such as panel con- figurations, connected devices, connected wires, may af- fect the protection level of this unit when it is integrated in a panel system. The user may have to review the CE requirements in regard to the whole system and employ additional protective measures to ensure the CE conform- ity. • Install lightning surge protectors for those wires connect- ed to remote locations. ■ POWER INPUT RATING & OPERATIONAL RANGE • Locate the power input rating marked on the product and confirm its operational range as indicated below: 100 – 240V AC rating: 85 – 264V (90 – 264V for UL), 47 – 66 Hz, approx. 3 – 5VA 24V DC rating: 24V ±10%, approx. 3W 11 – 27V DC rating: 11 – 27V, approx. 3W 110V DC rating: 85 – 150V (110V ±10% for UL), approx. 3W ■ GENERAL PRECAUTIONS • Before you remove the unit from its base socket or mount it, turn off the power supply and input signal for safety. ■ ENVIRONMENT • Indoor use. • When heavy dust or metal particles are present in the air, install the unit inside proper housing with sufficient ventilation. • Do not install the unit where it is subjected to continuous vibration. Do not subject the unit to physical impact. • Environmental temperature must be within -5 to +55°C (23 to 131°F) with relative humidity within 30 to 90% RH in order to ensure adequate life span and operation. • Be sure that the ventilation slits are not covered with ca- bles, etc. ■ WIRING • Do not install cables sclose to noise sources (relay drive cable, high frequency line, etc.). • Do not bind these cables together with those in which noises are present. Do not install them in the same duct. ■ AND .... • The unit is designed to function as soon as power is sup- plied, however, a warm up for 10 minutes is required for satisfying complete performance described in the data sheet. • With voltage output, do not leave the output terminals shortcircuited for a long time. The unit is designed to endure it without breakdown, however, it may shorten ap- propriate life duration.