MacDon R113 Manuals

R113/R116 Rotary Disc Pull-Type Unloading and Assembly Instruction (North America) 215585 Revision A Original Instruction The Harvesting Specialists.

R113/R116 Rotary Disc Pull-Type Road-Friendly Transport™ (MD #C2002) Installation Instructions 214633 Revision C Original Instruction The harvesting specialists.

R113 Rotary Disc Header M205 Compatibility Kit (MD #257188) Installation Instructions 215276 Revision A Original Instruction The Harvesting Specialists.

R113/R116 Pull-Type Disc Mower Quick Card MD #214799_A Supplement to R113/R116 Pull-Type Disc Mower Operator’s Manual R113/R116 Quick Card Subject to change without notice. Use this card as a guide only. Refer to your Operator’s Manual for detailed settings and adjustment procedures. Finger Clearance Increase conditioning: Move lever forward (A) to lower baffle and decrease clearance (C). Decrease conditioning: Move lever aft (B) to raise baffle and increase clearance (C). Conditioning Roll Tension Light crops—less tension: 1. Loosen jam nut (A). 2. Turn bolt (B) counterclockwise to increase exposed thread (C). 3. Tighten jam nut (A). Heavy/tough crops—more tension: 1. Loosen jam nut (A). 2. Turn bolt (B) clockwise to decrease exposed thread (C). 3. Tighten jam nut (A). Finger Rotor rpm Light crop/dry grass: 900 rpm – factory set Sensitive crop (new/thin alfalfa, thin grass): 600 rpm – swap pulleys (A) and (B) Header Angle Smooth/level/firm ground: Steep angle (B) Rocks/ridges/loose ground: Shallow angle (A) Hydraulic center-link Mechanical center-link Cutting Height Skid Shoes Short stubble/smooth ground: Upper position (A) High stubble/rocks/cane: Lower position (B) Roll Gap Decrease conditioning: 1. Loosen jam nut (A). 2. Turn lower nut (B) clockwise to increase roll gap (C). 3. Tighten jam nut (A). Increase conditioning: 1. Loosen jam nut (A). 2. Turn lower nut (B) counterclockwise to decrease roll gap (C). 3. Tighten jam nut (A).

R113/R116 Self-Propelled Disc Mower Quick Card MD #214620 Rev. A Supplement to R113/R116 SP Disc Mower Operator’s Manual R 11 3 / R 11 6 S P Q u i c k C a r d Subject to change without notice. Use this card as a guide only. Refer to your Operator’s Manual for detailed settings and adjustment procedures. Light / Thin Crop Light or Heavy / Tough Crop Disc Speed Rear Baffle Deflector Fins Controls material distribution across windrow. Narrower windrow. 1. Remove fins from storage position (on top of baffle). 2. Position deflector fin (A) under baffle. 3. Secure with existing bolt and nut (B) (bolt head facing down). 4. Adjust to approximately 60 degree angle (as shown). 5. Torque nut to 69 Nm (51 lbf-ft). Repeat on other side. Rear Baffle Plate Controls windrow height. Directs crop flow that affects width. 1. Remove lynch pin (A). 2. Pull adjustment lever (B) inboard to disengage from bracket (C). 3. Move lever forward—raise baffle—narrow swath. 4. Move lever backward—lower baffle—wide swath. 5. Release lever so tab engages the notch in bracket (C). 6. Secure lever with lynch pin (A). Controls windrow width and placement. 1. Loosen locking handle (A). 2. Slide adjuster bar (B) along adjuster plate (C) to desired position. 3. Engage bar (B) into a notch in the adjuster plate. 4. Tighten locking handle (A). 5. Repeat for other side to the same position. 6. Adjust rear baffle as required. Wide swath (A) Deflectors are angled outboard. Narrow swath (B) Deflectors are angled inboard. Side Deflectors—Roll Conditioner Smooth / level / firm ground: 16 km/h (10 mph) and higher, or until cutting and conditioning quality are compromised. Rocks / ridges / loose ground: Slow to minimize bouncing, uneven stubble, and damage to the cutterbar. (A) acres/hr (B) hectares/hr (C) km/h (D) mph (E) R116 (F) R113 Ground Speed Windrow

R113/R116 Pull-Type Disc Mower Unloading and Assembly Instruction: North America 214713 Revision A Original Instruction The harvesting specialists.

R1 Series Rotary Disc Pull-Types and Headers Eight- and Ten-Disc Cutterbar Kits (MD #259517 and 259518) Installation Instructions 214497 Revision D Original Instruction The Harvesting Specialists.

R1 SERIES PULL-TYPE DISC MOWER - QUICK START GUIDE WINDROW Side Deflectors (A) Wide: Deflectors outboard (B) Narrow: Deflectors inboard Roll Cond: Move bar (C) Finger Cond: Move handle (D) WINDROW TIPS: • Sharp blades reduce horse power requirements. • Install cutterbar filler plates in tall, stemmy crops. • Remove filler plate to reduce dirt accumula tion in cutterbar. FLOAT Rocks/Ridges/Loose Ground (100 lb): 1. Loosen (C) 2. Turn (D) Clockwise 3. Tighten (C) Smooth/Level/Firm Ground (125–150 lb): 1. Loosen (C) 2. Turn (D) Counterclockwise 3. Tighten (C) TRANSPORT Switch at (A) Light (C) on Switch at (B) Light (C) off Field Mode Transport Mode (A) Wide: Lower baffle (C) (B) Narrow: Raise Baffle (C) Finger Baffle Roll Baffle GROUND SPEED Smooth/Level/Firm Ground: 10 mph (16 kph) and higher until cutting and conditioning quality are compromised. Rocks/Ridges/Loose Ground: Slow to minimize bouncing, uneven stubble and damage to cutter bar. DISC SPEED 800 PTO rpm 1000 PTO rpm Light/Thin Crop Heavy/Tough Crop (A) acres/hr, (B) hectares/hr, (C) kph, (D) mph, (E) 16 ft., (F) 13 ft.