Master MH-410TCF-120 Manuals

Model Numbers MH-410TCF-120 CONSUMER: READ AND SAVE THESE INSTRUCTIONS Factory ID: 506 USE THIS HEATER ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. WARNING Safety Information FIRE OR EXPLOSION MAY OCCUR! Heater has hot arching or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. WARNING Unplug heater when not in use. Allow unit to cool completely before moving. Always carry product by the handle when moving it. CAUTION Properly ventilated air must be provided. High temperature environments may cause breathing difficulties. WARNING Sauk Rapids, MN 56379 USA • Toll Free (800) 641-6996 Fax: 320-251-2922 • Web: www.masterindustrialproducts.com • Email: [email protected] © 2020 Pinnacle Climate Technologies, Inc. MAEA-413 ELECTRIC RADIANT WORKSHOP HEATER User’s Manual & Operating Instructions NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE © 2020, Pinnacle Climate Technologies,Inc Electric Radiant Workshop Heater RISK OF FIRE. DO NOT use heater with extension cord. Plug the heater directly into a 120VAC receptacle. WARNING OVERHEATING OR FIRE MAY OCCUR. Do not place heater behind doors. WARNING BURN HAZARD. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving the heater. WARNING RISK OF ELECTRIC SHOCK OR INJURY. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away form the traffic area where it will not cause a tripping hazard. Do not operate any heater with a damaged cord or plug, or after heater malfunctions or has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair. WARNING RISK OF ELECTRICAL SHOCK. Connect to properly grounded outlets only. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. Unplug heater before performing any maintenance or when not in use. To disconnect heater, turn control to low, then remove plug from outlet. WARNING RISK OF FIRE. To prevent a possible fire, do not block intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Heater must be kept clear of all obstructions. Maintain a 1.5m / 5 ft. minimum clearance from front, sides, and rear. Heaters must be kept clean of lint, dirt, and debris. (See MAINTENANCE on Page 4). WARNING Safety Information CAUTION – RISK OF ELECTRIC SHOCK DO NOT OPEN HEATER SHELL NO USER-SERVICEABLE PARTS INSIDE WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. CAUTION! HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, ANIMALS, CLOTHING AND COMBUSTIBLES WARNING AWAY FROM HEATER. NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE © 2020, Pinnacle Climate Technologies,Inc Electric Radiant Workshop Heater Safety Information 1 Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on the power while you are working on the heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: WARNING RISK OF ELECTRIC SHOCK! WARNING Read all instructions before using this heater. WARNING – Extreme caution is necessary when any heater is used by or near children or invalids. – This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. – Always locate heater on a stable and level surface. – Do not place the heater against paperboard or low-density fiberboard surfaces. – Avoid using an extension cord because the extension cord may overheat and cause a risk of fire. – ALWAYS use only the electrical power (voltage and frequency) specified on the model plate of the heater. – ALWAYS use only three-prong, grounded outlet and extension cord. – ALWAYS unplug the heater when not in use. – Keep all combustible materials away from this heater Minimum Clearance From Combustibles MH-410TCF-120 Front 1.5m / 5 ft. Top 1.5m / 5 ft. Sides 1.5m / 5 ft. Rear 1.5m / 5 ft. Look for this icon throughout the manual for helpful tips on how to use and clean your Electric Radiant Workshop Heater. NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE © 2020, Pinnacle Climate Technologies,Inc Electric Radiant Workshop Heater Specifications Model # MH-410TCF-120 Watts 1500 Power (Volts) 120V-60Hz Amps 12.5 Heat Settings 1 Specifications subject to change without notice. Features MH-410TCF-120 Figure 1 On/Off Carbon Fiber Heating Bulbs Tip Over Safety Switch Height Adjustment Knob Tilt Adjustment Tri-pod Base 2