Maximum Controls MAX Manuals

www.max.us.com MAX.US.COM 12-10-20 _Rev 2.7 QUICK INSTALLATION GUIDE MAX KEYPAD RESIDENTIAL / COMMERCIAL APPLICATION Max Keyapd MAX CELL HUB POWER COMM LINK ONLINE CELL LINK RS485 5V (-) (+) GND Max Operator Max Cell Hub Timers Diagnose Users Settings GATE STATUS: OPEN, OPENING, CLOSED CLOSE OPEN LAGUNA WOODS GATE GATE RELEASE Max Cloud App 2 www.max.us.com www.max.us.com MAX Keypad MAX Keypad Max Keypad Overview Pedestrian door application Entry gate application Program Keypad greetings message Program Keypad call button message Program force open keycodes Program keycodes with restrictive times 3 4 6 7 8 9 10 TABLE OF CONTENT Max Operator Max Cell Hub Max Keypad requires a Max Cell Hub. Both work exclusively with Max Gate Operators 12-10-20 _Rev 2.7 3 www.max.us.com www.max.us.com MAX KEYPAD OVERVIEW MAX Keypad MAX Keypad ENCLOSURE Tamper resistant zinc die-cast front door KEY LOCK Vandal proof LCD DISPLAY Sunlight readable display (for greeting, help and other messages) LIGHT SENSOR For solar power management SPEAKERS For audio messages SIDE LEDs For goose neck nighttime visibility KEYPAD Back lit & vandal proof CALL button for visitors Displays phone # for visitor to call using their own phone HELP BUTTON To display help messages & play audio messages WIEGAND PORT • To support 26-bit card readers, radio receivers & RFID transponders • Program cards/keyfob, radio transmitters & transponder tags via Max Cloud App and assign optional time restrictions • Track wiegand device activity in event log RELAY PORT • Control access point with dedicated relay LCD CONTRAST for display contrast adjustment ACCESS PT Rotary switch to select access point # REQUEST TO EXIT (RTE) PORT • Supports exit switch request on pedestrian gates RS-485 COMM PORT • To connect to Max Cell Hub STATUS LEDs • Each port has indicator LEDs for easy troubleshooting POWER IN: 12 VDC / VAC 4 www.max.us.com www.max.us.com MAX KEYPAD 2 Wiring Hub to Keypad Connect RS-485 port of Max Cell Hub to RS-485 port of Max Keypad (+) to (+) (-) to (-) GND to GND 1 Wiring Power Input Connect 12VDC, 1A power transformer to Power Input port of Max Keypad (polarity does NOT matter) Verify POWER LED is ON Verify RS-485 LED turns ON otherwise revise your wiring MAX CELL HUB POWER COMM LINK ONLINE CELL LINK RS485 5V (-) (+) GND PEDESTRIAN DOOR APPLICATION MAX OPERATOR MAX CELL HUB POWER COMM LINK ONLINE CELL LINK RS485 5V (-) (+) GND MAX CELL HUB POWER COMM LINK ONLINE CELL LINK RS485 5V (-) (+) GND PEDESTRIAN DOOR MAX KEYPAD Call 949-000-000 on your phone Call 949-000-000 on your phone GND GND (+) (+) (-) (-) +12V GND

Maximum Controls LLC. • 949.699.0220 • 10530 Lawson River Ave, Fountain Valley, CA 92708 FOR PRO SERIES MAX Wireless Push Button OPEN OPEN CLOSED OPEN OPEN CLOSED Indoor Unit Mount Indoors in a secure place NOT exposed to the elements. ONLY use existing 4 holes to mount box. DO NOT drill any extra holes in box. The MAX wireless Open Button is designed to wirelessly OPEN or CLOSE a gate. It will also monitor the position of the gate with the LEDs. Press the Open Button to open the gate. Auto-close timer on gate operator will close the gate. If auto-close timer is turned OFF, press open button again to close gate. Install the indoor unit in a secure place protected from the elements. The outdoor unit gets installed at the gate operator within 3500 feet (Line-of-Sight) of the indoor unit. It can be exposed to the elements. Do not drill any extra holes in the boxes when mounting or running wires to them. Open Button Normal OPEN operation. Activates Relay 1. Gate Monitoring LED Wire Conduit Gate Monitoring LED 900MHz Robust Signal Up to 3500 ft using Line-of-Sight Indoor Unit Outdoor Unit See reverse side to wire outdoor unit to gate operator’s Matrix 1. Outdoor Unit POWER 12-24 V AC/DC 24 VDC Power Wire polarity does not matter. www.max.us.com EXIT PWR ALARM POWER / SOLAR IN BATTERY INPUT OPENING CLOSING CLOSING OPENING ERD OBD PORT BLACK BOX PROGRAMMING SOLAR MODE PROGRAM MOTOR OVER LOAD ERD MOTOR OVER LOAD MAX OFF MAX SENSE MAX SENSE BATTERY BACKUP MODE ERD SENSITIVITY MOTION CONTROL OPEN GATE SPEED MAG LOCK UL ENTRAP PRIMARY/ SECONDARY LINK STOP CLOSE MOTOR INPUTS CLOSE TIMER MAGLOCK DELAY JOG BATTERY TEST INPUT ERROR BATTERY BATTERY IN USE REPLACE BATTERY LEAVE CLOSED LEAVE OPEN OPEN 1 TIME BATTERY VOLTAGE E F 1/2 RESET / MANUAL RELEASE ID PLUG LINK OK MODULE PORT MOTOR POSITION INPUTS SLIDER LIMIT SWING LIMIT GND OPEN ONLY NC OPEN ONLY 10K PHOTO CLS NC OPEN/CLS NC GND 12VDC OUT GND GND GND GND GND GND JOG RIGHT JOG LEFT TAMPER IN TAMPER NO GATE DISABLE MANUAL RELEASE KEYPAD / CARD GND (-) (+) GND GND MAX OPEN FIRE DEPT RADIO GND RADIO SIGNAL STRIKE CLOSE COM COM STOP OPEN CLS ONLY 10K OPEN/CLS 10K 12VDC OUT NO COM NC ID PLUG ERROR 24VDC OUTPUT 12VDC OUTPUT GND GND GND LOOP PWR OFF PRIMARY LEFT ON/OFF BATTERY RIGHT SECONDARY ON QUICK CLOSE OPEN LEFT OPEN RIGHT GATE OFF 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 MIN MIN MAX MAX ON OFF 2.5 sec 1.5 sec FAULTS OPERATOR MATRIX III OFF OFF 3 1 14 16 MIN 16 MIN 12 9 7 3 1 14 12 9 7 UL SENSOR N.C. UL SENSOR 10K POWER MODE A MODE B EXIT LOOP LOOP LOOP CENTER SAFETY GATE OPEN COM GATE CLOSED MIN MATRIX III SWING / SLIDE Rev 7 -Jan/19 Input 1- OPEN Input 2- CLOSE Relay 1-NO Relay 1- C outdoor unit Mount at Operator (Outdoors) GROUND Connection: All inputs are lightning protected when box is properly grounded. Ground to operator chassis or ground rod. Signal QUALITY: 4 - Excellent 3-4 - Good 2-3 - Poor CHANNEL: ONLY use channels 0 thru 6. Channels MUST match on both units. 24 VDC Power 24 V DC STRIKE GND GND Polarity does not matter. (0-6) CHANNEL RANGE TEST RELAYS INPUTS Signal QUALITY OFF ON 1 POWER + - GND RS-485 RELAY 2-NC RELAY 2-C RELAY 2-NO GND INPUT 2 RELAY 1-NC RELAY 1-C RELAY 1-NO GND INPUT 1 + GND RS-485 + Ground Mounting Hole ONLY use existing 4 holes to mount box. DO NOT drill any extra holes in box. RANGE TEST: Channels MUST match on both units. Must remain OFF during normal operation. IN USE POWER Wire Conduit Outdoor Unit FOR PRO SERIES MAX Wireless Push Button www.max.us.com Gate Operator Matrix III 12-24 V AC/DC