Maximum MAESTRO 2-S Manuals

MAESTRO 2-S INSTALLATION PROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR, ELECTRICIAN OR TELEVISION ANTENNA INSTALLER (CHECK WITH YOUR LOCAL BUILDING SUPPLY, OR HARDWARE STORE FOR REFERRALS). TO PROMOTE CONFIDENCE, PERFORM A TRIAL WIRING BEFORE INSTALLATION. When assembling the wind direction sensor to the Z-mast, make certain that terminal #3 is aligned with the Z-mast arm. Slide the stub masts through the rubber boots and insert the stub masts into the bottom of the sensors. Secure with the cotter pins. Coat all wire connections with silicone sealant and slip the boots over the sensors. 2 1 5 TERMINAL #3 MUST ALIGN WITH Z-MAST ARM TERMINAL #3 WIND DIRECTION SENSOR BOSS WIND DIRECTION SENSOR COTTER PIN COTTER PIN STRAIGHT STUB MAST Z-STUB MAST 5-CONDUCTOR CABLE 2-CONDUCTOR CABLE BOOT WIND SPEED SENSOR Feed the terminal lug end of the five-conductor cable through the other rubber boot and connect the lugs to the terminals on the bottom of the wind-direction sensor. (Do NOT adjust the nuts that are already on the sensor). The red sleeve indicates wire #1. Feed the teminal lug end of the 2-conductor cable through one of the rubber boots and connect the lugs to the terminals on the bottom of the wind speed sensor. (Do NOT adjust the nuts that are already on the sensor). The polarity does not matter. Determine where you are going to locate both the rooftop sensors and the read-out. 4A 4 3 2-CONDUCTOR CABLE BOOT BOSS T-4 (S & SW) T-2 (E & SE) T-3 (POWER) T-5 (W & NW) 1 3 4 5 2 TERMINAL-1 (N & NE) RED SLEEVE 5-CONDUCTOR CABLE BOOT Secure the sensors and stub masts to your antenna mast (not supplied) with the two hose clamps. Align the wind-direction Z-mast arm to true North. Radio Shack and similar stores have a selection of tall masts and roof mounting brackets. Choose a mount that best suits your location and provides at least eight feet of vertical clearance above objects on the roof. HOSE CLAMPS NORTH 1.888.610.7664 [email protected] Fluke-Direct.com

SIROCCO INSTALLATION PROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR ELECTRICIAN OR TELEVISION ANTENNA INSTALLER (CHECK WITH YOUR LOCAL BUILDING SUPPLY, OR HARDWARE STORE FOR REFERRALS). TO PROMOTE CONFIDENCE, PERFORM A TRIAL WIRING BEFORE INSTALLATION. HOSE CLAMPS TALL MAST DRIP LOOP WIRE-HOLE WIRE SCREW WALL WALL ANCHOR (NOT SUPPLIED) CAULK WIRE Determine where you are going to locate both the rooftop sensor and the read-out. Feed the terminal lug end of the 2-conductor cable through the rubber boot and connect the lugs to the terminals on the bottom of the wind speed sensor. (Do NOT adjust the nuts that are already on the sensor). The polarity does not matter. Slide the stub mast through the rubber boot and insert the stub mast into the bottom of the wind speed sensor. Secure with the cotter pin. Coat all conections with silicone sealant and slip the boot over the sensor. Secure the sensor and the stub mast to your antenna mast (not supplied) with the two hose clamps. Radio Shack and similar stores have a selection of antenna masts and roof mounting brackets. Choose a mount that best suits your location and provides at least eight feet of vertical clearance above objects on the roof. Feed the cable through the wall to where the read-out is going to be located. Attach the wires to the rear of the read-out as shown. (Do NOT adjust the nuts that are already on the meter). The polarity does not matter. The Sirocco read-out is free standing. It can also be mounted on a wall using the key hole cut outs in the back of the instrument's wood block. Secure the wire to the building using cable clips (do not use regular staples). Form a drip loop where wire enters hole drilled through the exterior wall. Caulk the hole when done. Follow the instructions supplied with the antenna mount and secure the mast to the mount. CABLE CLIPS 1 2 3 4 5 6 8 7 8 FEET CHIMNEY MOUNT VENT-PIPE MOUNT TRIPOD MOUNT WALL MOUNT EVE MOUNT 2-CONDUCTOR CABLE BOOT COTTER PIN STRAIGHT STUB MAST 2-CONDUCTOR CABLE WIND SPEED SENSOR www. .com [email protected] 1.800.561.8187