MaxLite ML2LA P Series Manuals

Operating Instructions WARNING: • Risk of Fire - Supply conductors (power wires) connecting the fixture must be rated minimum 90℃. If uncertain consult an electrician. • Risk of Fire/Electric Shock - If not qualified, do not attempt installation. Contact a qualified electrician. CAUTION: • For your safety read and understand instructions completely before starting installation. • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. • Before attempting installation, check your local electrical code, as it sets the wiring standards for your locality. NOTES: • If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch. • Make certain no bare wires are exposed outside the wire nut connectors. • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. • Warranty is not applicable to lamps not installed in compliance with: - National Electrical Code (NEC) - The Standard for Safety of Underwriters Laboratories Inc. (UL) SERIES: ML2LAxA CCT SELECTABLE Operating Temperature: -20°C to 40°C Damp Location Rated PRODUCT DIMENSIONS: General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. • Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician. • For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code. • DO NOT INSTALL DAMAGED PRODUCT! • This fixture is intended to be connected to a properly installed and grounded UL listed junction box. MaxLite LED ARCHITECTURAL CCT SELECTABLE ® Picture is for illustration purposes only. Your model may vary. © Copyright 2020. MaxLite, Inc. All Rights Reserved. 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: [email protected] Page: 1 REV: 06/19/20 120V 120- 277V Small Small Medium Medium Large Large ML2LAxA Series 15.98” 5.12” 14.01” 4.76” 11.81” 4.29” 15.04” 5.12” 13.03” 4.8” 5.07” 10.94” 10.94” 4.02 3.74 13.03” 15.04” 11.81” 3.43” 14.01” 3.9” 15.87” 3” 15.04” 15.87” 4.33” 10.94” 4.02” 11.81” 3.43” 15.98” 5.12” 14.01” 4.76” 11.81” 4.29” 15.04” 5.12” 13.03” 4.8” 15.98” 5.12” 14.01”

Operating Instructions WARNING: • Risk of Fire - Supply conductors (power wires) connecting the fixture must be rated minimum 90℃. If uncertain consult an electrician. • Risk of Fire/Electric Shock - If not qualified, do not attempt installation. Contact a qualified electrician. CAUTION: • For your safety read and understand instructions completely before starting installation. • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. • Before attempting installation, check your local electrical code, as it sets the wiring standards for your locality. NOTES: • If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch. • Make certain no bare wires are exposed outside the wire nut connectors. • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. • Warranty is not applicable to lamps not installed in compliance with: - National Electrical Code (NEC) - The Standard for Safety of Underwriters Laboratories Inc. (UL) SERIES: ML2LAxP CCT SELECTABLE Operating Temperature: -20°C to 40°C Damp Location Rated PRODUCT DIMENSIONS: General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. • Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician. • For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code. • DO NOT INSTALL DAMAGED PRODUCT! • This fixture is intended to be connected to a properly installed and grounded UL listed junction box. MaxLite LED PUFF CCT SELECTABLE ® Picture is for illustration purposes only. Your model may vary. © Copyright 2020. MaxLite, Inc. All Rights Reserved. 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: [email protected] Page: 1 REV: 06/18/20 120V 120- 277V Small Small Medium Medium Large Large ML2LAxP Series 15.98” 5.12” 14 01” 15.04” 5.12” 15.98” 14.01” 11.81” 15.04” 5.12” 13.03” 4.8” 15.04” 5.12” 13.03” 4.8” 5.07” 10.94” 10.94” 4.02” 10.94” 4.02” 3.74” 13.03” 15.04” 09” 15.04” 4.09”