Maxwell Digital Multimeters WH806 Manuals

WIRE TRACKER WITH SOUND ALERT, LED - RJ45 CABLE TESTER HU: ÉRPÁRKERESŐ HANGJELZÉSSEL, LED-DEL - RJ45 KÁBEL TESZTERREL CZ: VYHLEDÁVAČ KABELOVÝCH PÁRŮ SE ZVUKOVOU SIGNALIZACÍ, LED - RJ45 TESTEREM KABELŮ SK: VYHĽADÁVAČ KÁBLOVÝCH PÁROV SO ZVUKOVOU SIGNALIZÁCIOU, LED - RJ45 TESTEROM KÁBLOV RO: TESTER PT. PERECHI DE CABLURI, CU LED - CU TESTER CABLU RJ45 User ManUal Használati Utasítás návod k poUžití návod na poUžitie ManUal de Utilizare CZ EN HU SK RO 25341 accessories • Emitter device • Receiver device • RJ45 Cable • RJ11 Cable • Earphone • 9 V battery (2pcs) • Crocodile clamp • Carrying case Network wire sequence collation: 1. Insert RJ45 plug at two ends of the network wire into the corresponding sockets at emitter and receiver. 2. Set Function switch of emitter to “TEST”, testing indicator “VERIFY” flashes meaning normal work of emitter. 3. After some testing, judge the characteristics of short-circuit, breaking circuit, open circuit and crossing. 4. During testing, SELECT button can be pressed for switchover of fast and slow levels. Open circuit of short circuit testing function: Set function switch on emitter to position of “TEST”, and long press SELECT button on emitter for at least 2 seconds, “VERIFY” indicator will change “flash” to “lighting” insert the plug with crocodile clamp into RJ11clamp the two ends to be tested with crocodile clamps, in case of short circuit, the first led “1” of wire sequence indicator of emitter will light up, otherwise it will not light up, resistance of the line can be indicated be brightness of status indicators: the lighter the indicator, the smaller the resistance; the darker the indicator, the bigger the resistance. Telephone wire finding function: 1. Directly insert telephone wire with RJ11 plug into the RJ11 or RJ45 socket of the wire tracker’s emitter; 2. Set function switch of emitter to position of “SCAN” then wire finding indicator “STATUS” flashes meaning normal work of emitter; 3. Press and hold test button of Receiver, use the probe of receiver to find target wire at the other end; RJ45 Socket RJ45 Socket Probe Signal indicator Flashlight Volume adjust Flashlight switch RJ11 Socket Wire fnding indicator Wire sequence indicator SELECT button Verify LED Earphone socket (jack) Teszt button Wire sequence indicator Function switch EN 4. During testing, select button can be pressed for switch single-tone or dual-tone. Network wire finding function 5. Directly insert network wire with RJ45 plug into the RJ45 socket of the wire tracker’s emitter; 6. Set function switch of emitter to position of “SCAN” then wire finding indicator “STATUS” flashes meaning normal work of emitter; 7. Press and hold test button of Receiver, use the probe of receiver to find target wire at the other end; 8. During testing, select button can be pressed for switch single-tone or dual-tone. Ideal for cable management in rack cabinets DC level testing function Set function switch on emitter to position of “SCAN”, and long press select button on emitter for at least 2 seconds, “STATUS” indicator will turn off and “VERIFY” indicator flashes, insert the plug with crocodile clamp into RJ11clamp the two ends to be tested with crocodile clamps, in case that “STATUS” indicator lights up in red, it means the end clamped with red clamp is positive pole, in case that “STATUS” indicator lights up in green, it means the end clamped with red clamp is negative pole, electric level can be judged by brightness of the status indicators; the lighter the indicator, the smaller the resistance; the darker the indicator, the bigger the resistance. Low battery alarm function Set function switch on emitter to position of “TEST”, in case that battery level is lower than 7 V, “STATUS” and VERIFY” indicators will light up at the same time, it means battery replacement is needed. Earphone function In noisy environment, earphone can be used to prevent interference from the outside. Spotlight function You can easily work as usual while putting on the light switch at night and in the dark. Functions Telephone wire finding  Network wire finding  Electric wire finding  Network wire sequence  Open or short circuit testing  DC level testing  Low voltage alarm  Earphone(Accessory)  Spotlight  Volume adjusting  Specification Name Wire tracker Power supply 9 V 6F22 The max working current Emitter: ≤ 9 mA Receiver: ≤ 28 mA Signal transmission format Multi-frequency impulse Signal output electric status 8VP-P Distance of signal transmission ≤ 3 km Emitter size 125 x 46 x 25 mm Receiver size 173 x 36 x 23 mm