Mellerware 23101 Manuals

2 y e a r g u a r a n t e e V o y a g e r T r a v e l I r o n Model: 2 3 1 0 1 1000W PLEASE READ ALL INSTRUCTIONS BEFORE USE MW_CO23101 Voyager_IM.indd 1 MW_CO23101 Voyager_IM.indd 1 3/6/2009 9:30:18 AM 3/6/2009 9:30:18 AM IRONING TEMPERATURES WARNING! Always check the label on the article to be ironed for correct ironing instructions! • Sort the laundry separating different fabric types – wool with wool and cotton with cotton etc. Start ironing the fabrics requiring the lowest temperatures (synthetics) first and progress to a higher temperatures as the iron heats up quicker than it cools. If the fabric to be ironed has various fiber materials (e.g. cotton with polyester), use the lower/lowest ironing temperature. X KIND OF TEXTILE Synthetic Synthetic Wool FIBRE MATERIAL Acrylic Modacryl Polypropylene Polyurethane Acetate Triacetate Synthetic Silk Metallized Cupro Polyamide (Nylon) Polyester Modal Viscose (Rayon) Silk Wool Cotton Linen Cotton Linen TEMPERATURE KNOB POSITION LABEL NOTE: On label means: THIS ARTICLE CANNOT BE IRONED! (eg: Chlorofibre, Elastodiene) MW_CO23101 Voyager_IM.indd 2 MW_CO23101 Voyager_IM.indd 2 3/6/2009 9:30:19 AM 3/6/2009 9:30:19 AM Description 1 Filling apeture for water tank 2 Revolving handle 3 Spray / Vapour jet knob 4 Revolving handle lock 5 Temperature regulator 6 Control lamp 7 Voltage changeover switch 8 Spray nozzle CHARACTERISTIC Temperature Dial Knob Power Indicator Light Soleplate Water Filling Aperture Transparent Water Tank Dry/Steam Iron Selector Spray Button Voltage changeover switch FUNCTION Adjust temperature according to fabric to be ironed.(see table below) Indicator light will go off when desired temperature is reached. The light will go on and off as the temperature is regulated by the adjustable thermostat. Super smooth non stick ironing surface. If ironing surface is sticky ensure temperature setting is correct as per table below and item being ironed is clean. Using the measuring cup only, fill the tank with clean water here. Use demineralized water in hard water areas or water with lime scale. Do not overfill. Water level in tank is easily visible during ironing. Choose desired level of steam or dry ironing by sliding the knob Depress for spraying water onto fabric for dry ironing or when required. Use this switch to change between 115V or 230V KEY and CHARACTERISTICS 1 2 3 4 5 6 7 8 Dry/Steam selector knob Voltage changeover switch MW_CO23101 Voyager_IM.indd 3 MW_CO23101 Voyager_IM.indd 3 3/6/2009 9:30:19 AM 3/6/2009 9:30:19 AM IRONING INSTRUCTIONS Note: The iron may smoke slightly when switched on for the first time. This is normal and will soon cease. Please read these instructions carefully before use. Important!: have you read the section “Impor tant Safeguards”? CHOICE OF WATER - This iron can be used with normal tap water. - If the water in your area is particularly hard. It is advisable to use distilled or demineralized water to prevent the scale forming on the critical point of the iron. - Do not use chemically de-scaled water. FILLING WITH WATER - Ensure that the iron is disconnected from the power supply before filling. - Turn the dry/steam selector dial to “0” or dry position. - Fill water through the aperture using the measuring cup only. (If you fill the iron at the tap water can spill into the electrics and trip your earth leakage or blow the iron.) Note* Do not fill higher than indication “MAX” of the water tank, In order to avoid spilling out of water. - Do not fill with any thing but clean water. If you have to refill while ironing, remove the mains plug from the wall socket before filling. - Pour out any remaining water after use. SETTING THE TEMPERATURE - Insert the plug in the wall socket and stand the iron upright. - Set the temperature control dial to the correct temperature as indicated in the ironing instructions on the label or as per table above. - The correct temperature will be reached when the indication light has gone. The indication light will be on and off from time to time indicating that the selected temperature is being maintained. Note: Water may leak from the soleplate if the temperature selected is too low. This will then cause stains. If it happens, Set the temperature control to the advised position for steam ironing. Steaming will re-commence as soon as the appropriate temperature has been reached. MW_CO23101 Voyager_IM.indd 4 MW_CO23101 Voyager_IM.indd 4 3/6/2009 9:30:19 AM 3/6/2009 9:30:19 AM