MikroTik LtAP mini Manuals

LtAP mini LtAP mini (RB912R-2nD-LTm) The LtAP mini is a wireless access point with two SIM card slots for 3G/LTE data. The LtAP mini is designed for use with your own modem. Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. Ultimate disposal of this product should be handled according to all national laws and regulations. All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction. The Installation of the equipment must comply with local and national electrical codes. This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product. Read the installation instructions before connecting the system to the power source. We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk! In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet. It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed. Exposure to Radio Frequency Radiation: This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an uncontrolled environment. This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the general public. Connecting Install your desired modem (see " "). miniPCIe slot usage If the intent to use GPS, an external antenna is required (see " "). GPS usage Choose your powering solution (see " "). Powering Connect your Internet cable to the Ethernet port. Set your computer IP configuration to (DHCP). automatic Connect your direct input power jack if not using PoE, to start up the device. The device will boot up and the Wireless network will be available for connecting. Open network connections on your PC, mobile phone, or other device and search for MikroTik wireless network and connect to it. Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1 default, you will be logged in automatically. The configuration also can be done using a mobile app (see " "), and WinBox MikroTik mobile app configuration tool . https://mt.lv/winbox We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and stability. Choose your country, to apply country regulation settings, and set up your password on the screen that loads. Mounting

1. 2. 3. 4. LtAP mini LtAP mini The LtAP mini is a wireless access point with two SIM card slots for 3G/LTE data. The LtAP mini is designed for use with your own modem. Connecting Install your desired modem (see " "). miniPCIe slot usage If the intent to use GPS, an external antenna is required (see " "). GPS usage Choose your powering solution (see " "). Powering Connect your Internet cable to the Ethernet port. Set your computer IP configuration to (DHCP). automatic Connect your direct input power jack if not using PoE, to start up the device. The device will boot up and the Wireless network will be available for connecting. Open network connections on your PC, mobile phone, or other device and search for MikroTik wireless network and connect to it. Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1 default, you will be logged in automatically. The configuration also can be done using a mobile app (see " "), and WinBox MikroTik mobile app configuration tool . https://mt.lv/winbox We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and stability. Choose your country, to apply country regulation settings, and set up your password on the screen that loads. Mounting It is possible to attach the device to a wall, using the provided screw holes on the sides of the unit. The device should be mounted in a way that the cable openings are pointing downward as shown in the picture. The ports are protected with a small door, that is held in place with one screw. Use the Philips PH2 screwdriver to access the ports. The door has cut-out places for all available ports, but please only break out the openings that you will use. The device can be used both indoors and outdoors. The IP rating scale for this device is IP54. The device enclosure has places where you can drill openings for external LTE and GPS antennas. Use a drill to make holes that are appropriate for the antenna cable used. Alternatively, you can obtain a "DINrail Pro" - mounting bracket, designed to fit standard 35 mm x 7.5 mm DIN rails. https://mikrotik.com/product/dinrail_pro When mounting outdoors, please ensure that any cable openings are directed downwards. Use a PoE injector and proper grounding. Recommended using Cat6 cable.