Minicom Advanced Systems 5UM60000 Manuals

Technical support - [email protected] © 2009 Copyright Minicom Advanced Systems. All rights reserved. 5UM60000 V1.2 9/09 DX User IP II - Quick Start Guide 1. Introduction To take advantage of the DX User IP II full range of features, we recommend you read the softcopy User Guide after performing the Quick Start procedure. It’s in PDF format on the supplied CD or on our website www.minicom.com in the Support section. Figure 1 illustrates the basic configuration of the DX system with the DX User IP II and DX Users connected to peripheral devices via the DX Central. DX 432 Central X-RICC X-RICC X-RICC 1 32 Computer To computers Computer Power Link MINICOM DX 432 Central Local User MINICOM Power DX User DX User Computer DX User IP II Local User MINICOM System OK Activity DXU - IP II Internet / VPN / LAN Remote User Figure 1 DX User IP II usage scenario DX USER IP II 1 1.1 Standalone mode or KVM.net DX User IP II can be used in any of the following 3 modes: • Standalone • KVM.net enabled • KVM.net managed KVM.net is a centralized IP based system for secure control of servers and network devices, power and user administration in the data center environment. KVM.net combines Out-Of-Band, KVM via IP access with modern IT standards and requirements. It is the most comprehensive remote server maintenance solution available in the market today. These 3 modes are now explained. 1.1.1 Standalone mode Standalone mode refers to using the DX User IP II as part of the DX system only and working via the DX AIM interface without KVM.net, for remote KVM access and control via a LAN or Internet connection. 1.1.2 KVM.net enabled / managed The DX User IP II can be KVM.net enabled or KVM.net managed. Both of these refer to managing and accessing servers connected to the DX system via the KVM.net Manager. KVM.net enabled means the DX is still capable of working in Standalone mode. KVM.net managed means the DX is fully managed and controlled by KVM.net, access to the AIM interface is blocked but can be achieved where necessary via hotkeys. Details of the differences between KVM.net enabled and managed will be explained in the configuration and operating sections later on in this Guide. 2. DX User IP II front panel Figure 2 illustrates the DX User IP II front panel. MINICOM System OK Activity DXU - IP II Figure 2 Front panel The table below explains the functions of the front panel LEDs. QUICK START GUIDE 2 LED Function Activity LED solid when a remote user operates the DXU IP II System OK LED solid when DX User IP II connected and functioning 2.1 DX User IP II rear panel Figure 3 illustrates the rear panel of the DX User IP II. Power connector RS232 Serial port POWER 100-240 VAC 50/60 Hz www.minicom.com Go Lock button Ethernet port ETHERNET SERIAL I 0 SYSTEM Keyboard Mouse Monitor USB TERMINAL USER USB ports RS232 Terminal port CAT5 to DX Central GO LOCK DX Reset button SERIAL 2 Serial 2 port Figure 3 DX User IP II rear panel ports DX Reset button The DX Reset button resets the DX parts of the DX User IP II. Go Lock button The Go Lock button disconnects the active remote session and returns control to the local user. Serial / Serial 2 port The Serial port is only used for KVM.net managed mode when the DX User IP II is the Master Console – (explained in the softcopy User Guide). In Standalone and KVM.net enable modes, the Serial 2 port can be used for any RS232 application, e.g. managing a router or power switch. Terminal port In Standalone and KVM.net enable modes only, when there are X-RICC RS232s in the DX system, you can control them locally through an RS232 terminal connected to the DX User IP II. Ethernet - Connects the DX User IP II to an Ethernet network. DX USER IP II 3 USB ports Update the DXU firmware via a Minicom Flash USB key. See the DX User Guide for information on updating firmware. System port – Used to connect the DX User IP II to the DX Central. KVM ports – Used for optional local console. 3. Pre-installation guidelines • Place cables away from fluorescent lights, air conditioners, and machines that are likely to generate electrical noise • The maximum distance between each device (computer, KVM switch or second level DX Central) and the DX Central is 100m/330ft. The maximum distance between the DX Central and the DX User IP II is also 100m/330ft. For best performance place the DXU IP II as close as possible to the DX Central. 4. Connecting the DX User IP II Figure 4 below illustrates the connections of the DX User IP to the DX system. See below for more details. POWER 100-240 VAC 50/60 Hz www.minicom.com ETHERNET SERIAL I 0 SYSTEM USB TERMINAL USER GO LOCK SERIAL 2 SD P110 CAT5 cable To DX Central User port Internet / VPN / LAN Remote user (Optional) Local User console Figure 4 DX User IP connections