Mircom TX3-TOUCH-S15B-WR Manuals

Version 8 TX3 Touch Screen Installation Manual 1 LT-996 Copyright August 2020 TX3 Series Touch Screen Installation Manual

Version 1 TX3-TOUCH-S15B-WR and TX3-TOUCH-S15S-WR Installation 1 LT-6651 Copyright 2019 1 TX3-TOUCH-S15B-WR and TX3-TOUCH-S15S-WR Installation For field wiring, refer to LT-996 TX3 Touch Screen Installation Manual. For configuration, refer to LT-995 TX3 System Configuration and Administration Manual. These manuals are available on http://www.mircom.com 1.1 Installation The enclosure mounts on the wall. Mount the enclosure with the right side up (the Mircom logo on the door is on the bottom). To mount the enclosure You need: 4 fasteners appropriate for the wall that you are mounting the enclosure on. 1. Find a suitable location for the enclosure. 2. Using the enclosure as a template, mark the back mounting locations of the two keyholes shown in Figure 1. Ensure that at least one side is over a wall stud. 3. Remove the enclosure and place the fasteners halfway into the wall into the marked hole locations. 4. Place the enclosure onto the fasteners and lower it so that the fasteners fit in the narrow part of the keyholes. 5. Screw the other two fasteners into the two remaining holes. 6. Tighten all fasteners into place. Warning: To prevent water from entering the unit, use an elbow connector to run the wires to one of the three knockouts on the back. The elbow connector must point downwards.

LT-6649 Rev 0 Page 1 of 2 Replacement Card Reader Window and Camera Window for TX3-TOUCH-S15B-WR and TX3-TOUCH-S15S-WR Figure 1 Card reader window and camera window dimensions Card Reader Window Replacement A. Disconnect the Power B. Remove the Card Reader Assembly Remove the card reader, the metal bracket, and the plastic plate. Figure 2 Parts of the card reader assembly C. Replace the Card Reader Window D. Replace the Card Reader Assembly Replace the plastic plate, the metal bracket, and the card reader as shown in Figure 2. You are done! If you need more help, call us at 1-888-660-4655. 1.87” 4.6” 2.59” 2.2” Card reader window Camera window 2 x screws Card reader 4x nuts Card reader metal bracket Card reader plastic plate Card reader window

LT-6656 Rev 1 Page 1 of 3 Replacement Display for TX3-TOUCH-S15B-WR and TX3-TOUCH-S15S-WR A. Shut down the Touch Screen 1. Press the On/Off switch located at the bottom of the inner chassis. 2. After the TX3 Configurator and Windows have finished shutting down, disconnect power from the Touch Screen. Remove the old display 1. Disconnect the cables from the current display. 2. Unscrew the 8 nuts that hold the display assembly to the door. See Figure 1. Figure 1 Display on door (back view) 3. Unscrew the 8 screws that hold the 4 brackets to the display. See Figure 2. On/Off Switch 4 nuts 4 nuts Display assembly Door

LT-6656 Rev 0 Page 1 of 2 Replacement Display for TX3-TOUCH-S15B-WR and TX3-TOUCH-S15S-WR A. Shut down the Touch Screen 1. At the Touch Screen terminal, enter 9999. 2. Enter your administrator password, and then press OK. 3. Select File > Shut down > Shut down. 4. After the TX3 Configurator and Windows have shut down, disconnect power from the Touch Screen. 5. Turn off the lobby controller board. B. Remove the old display 1. Disconnect the MD-990 power supply. 2. Disconnect the cables from the current display. 3. Unscrew the 4 nuts that hold the display assembly to the door. See Figure 2. 4. Unscrew the 4 screws that hold the brackets to the display. See Figure 1. C. Attach the new display 1. Secure the new display to the brackets with the four screws you removed in step B. See Figure 1. Figure 1 Display assembly display bracket 4 screws bracket