Mongoose M80i Manuals

M80 Series MODELS: M80i, M80S, M80GNZ, M80G USER OPERATION MANUAL All models certified to AS/NZS4601 1999 amendment 1 M80S certified to AS/NZS3749.1 2003 Class B M80G/GNZ certified to AS/NZS3749.1 2003 Class A These products should be installed according to the requirements of the AS/NZS 3749.2 Installation Standard. Installation should only be carried out by suitably qualified persons. References to alarm functions and siren/horn responses do not apply to model M80i. REMOTE CONTROL 2 Supplied BUTTON ‘THREE’ ‘PANIC’ PRESS FOR 3 SECONDS TO SOUND THE ALARM SYSTEM. PRESS AGAIN TO CANCEL. BUTTON ‘ONE’ THEN ‘THREE’ ‘SENSOR BYPASS’ THIS DEACTIVATES ANY CONNECTED SENSOR. ONLY DEACTIVATE SENSORS TO REDUCE THE POSSIBILITY OF FALSE ALARMS. TURBO TIMER BUTTON ‘TWO’ & ‘THREE’ TOGETHER PRESS WITH IGNITION ON TO TURN THE BUILT-IN TURBO TIMER ON/OFF. See page 7 BATTERY REPLACEMENT CR2032 LITHIUM BATTERIES ARE AVAILABLE FROM YOUR MONGOOSE AGENT OR USUAL BATTERY OUTLET. PLEASE CHANGE ANNUALLY OR IF OPERATION BECOMES INTERMITTENT. BUTTON ‘ONE’ ‘ARM or DISARM’ PRESS ONCE FOR 1SECOND TO ARM OR DISARM THE SECURITY SYSTEM - (DOORS WILL ALSO LOCK OR UNLOCK IF THE CENTRAL LOCKING HAS BEEN CONNECTED) PRESS FOR 2~3 SECONDS IF TURBO TIMER IS ON BUTTON ‘TWO’ PRESS FOR 3 SECONDS FOR ‘AUXILIARY OUTPUT’ (EG: BOOT RELEASE) BUTTON ‘TWO’ THEN ‘ONE’ ‘SILENT ARM or DISARM’ THIS SEQUENCE WILL SILENTLY ARM OR DIS-ARM THE ALARM – NO SIREN CHIRPS CONTENTS Automatic engine immobilisation.. 4 Arm condition memory............... 10 Arming………… …….................... 5 Noise pollution control......….…. 10 Open circuit bypass….…………… 5 Indicator flashing……………..… 11 Central locking........…............… .. 5 Dash mounted warning light….. 11 Disarming…………………………. 6 Chirp confirmation…................. 11 Security re-arm……………….….. 6 Car Finder & Panic...….......….. 12 Silent arm/disarm ……………….… 6 Boot release………….......….... 12 Bonnet, boot & doors……………… 6 Programme options..…............ 13/14 Built-in turbo timer…………………. 7 Remote controls………............ 14 2 stage impact sensor (excl’ M80i) 8 Remote code learning.............. 14/15 Glass break sensor……………….. 8 EMERGENCY OVERRIDE…… 16 Sensor disable...…………….......... 8 PIN code programming…….…. 17 Intrusion alert ……………….…….. 8 Testing your alarm…….………. 18 Optional extras……………………. 9 Battery back-up siren (M80S/G)... 10 Wiring , programming & warranty Automatic re-set………………….. 10 Proof of purchase OPERATING YOUR VEHICLE SECURITY SYSTEM AUTOMATIC ‘TRIPLE CIRCUIT’ ENGINE IMMOBILISATION The engine always immobilises automatically 30 seconds after the ignition has been turned off. When you turn the ignition OFF, the dashboard LED will start to fast flash for 30 seconds to indicate the automatic sequence has commenced. At the end of the 30 seconds, the siren will chirp once (alarm models only), the indicators will flash once and the dashboard LED will slow flash as confirmation of immobilisation. Only the engine is immobilised, the alarm system is not yet armed. If an attempt is made to start the engine whilst immobilised, the siren will chirp a warning – fully sounds if armed by remote. ONCE IMMOBILISED, PRESS BUTTON ONE TO DISENGAGE THE ENGINE IMMOBILISERS NOTE: If the system has automatically immobilised the engine and you now wish to arm the security system (& lock the doors), press button one twice. The installer of this system will immobilise three of the following possible circuits to prevent engine starting;  Starter motor  Ignition system  Electric fuel pump  Other engine controlling circuit Ask the installer which circuits are immobilised for future reference. 4