Moxa Technologies ioLogik E1242 Manuals

P/N: 1802012001016 *1802012001016* ioLogik E1200 Series Quick Installation Guide Ethernet Remote I/O Version 6.1, January 2021 Technical Support Contact Information www.moxa.com/support  2021 Moxa Inc. All rights reserved.

– 1 – – 2 – – 3 – P/N: 1802012001011 ioLogik E1200 Series Quick Installation Guide Second Edition, February 2011 1. Overview The ioLogik E1200 series comes with 2 embedded Ethernet switch ports that can form a daisy-chain topology, which is the easiest way to add more Ethernet devices to a network or connect your ioLogiks in series. Moxa’s free Active OPC Server offers active (or “push”) communication that works between Moxa’s ioLogik units and HMI/SCADA systems, providing instant I/O status reports by “Active Tags.” The event-driven active tags result in an I/O response time that is 7 times faster than other OPC Server packages and an 80% reduction in network traffic. Model Selection: ioLogik DI DO DIO Relay AI AO RTD TC E1210 16 – – – – – – – E1211 – 16 – – – – – – E1212 8 – 8 – – – – – E1214 6 – – 6 – – – – E1240 – – – – 8 – – – E1241 – – – – – 4 – – E1242 4 – 4 – 4 – – – E1260 – – – – – – 6 – E1262 – – – – – – – 8 Package Checklist • 1 ioLogik E1200 series remote I/O product • Documentation and software CD • Quick installation guide (printed) 2. Specifications System Ethernet: 2 x 10/100 Mbps switch ports, RJ45 Protection: 1.5 KV magnetic isolation Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP Power Input: 24 VDC nominal, 12 to 36 VDC Wiring: I/O cable max. 14 AWG Dimensions: 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) Weight: under 200 g Operating Temperature: Standard Models: -10 to 60°C (14 to 140°F) Operating Temperature: Wide Temperature Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Standards and Certifications: UL 508, CE, FCC Class A Warranty Period: 5 years (excluding ioLogik E1214*) Details: See www.moxa.com/warranty *Because of the limited lifetime of power relay, products that use this component are covered by a 2-year warranty. Digital Input Sensor Type: NPN, PNP, and Dry contact I/O Mode: DI or Event Counter Dry Contact: • Logic 0: short to GND • Logic 1: open Wet Contact: • Logic 0: 0 to 3 VDC • Logic 1: 10 to 30 VDC (DI COM to DI) Isolation: 3K VDC or 2K Vrms Counter/Frequency: 250 Hz, power off storage Digital Output I/O Mode: DO or Pulse Output Pulse Wave Width/Frequency: 1 ms/500 Hz Over-voltage Protection: 45 VDC Over-current Protection: 2.6 A (4 channels @650 mA) Over-temperature Shutdown: 175°C (typical), 150°C (min.) Current Rating: 200 mA per channel Isolation: 3K VDC or 2K Vrms Relay Output Type: Form A (N.O.) relay outputs, 5A Contact Rating: 5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110 VAC Inductance Load: 2 A Resistance Load: 5 A Breakdown Voltage: 500 VAC Relay On/Off Time: 1500 ms (Max.) Initial Insulation Resistance: 1G min. @ 500 VDC Expected Life: 100,000 times (Typical) Initial Contact Resistance: 30 milli-ohms (Max.) Pulse Output: 0.3 Hz at rated load Analog Input Type: Differential input Resolution: 16 bits I/O Mode: Voltage / Current Input Range: 0 to 10 VDC, 4 to 20 mA Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -10 and 60°C ±0.5% FSR @ -40 and 75°C Sampling Rate (all channels): 12 samples/sec Input Impedance: 10M ohms (minimum) Built-in Resistor for Current Input: 120 ohms Analog Output Resolution: 12 bits Output Range: 0 to 10 VDC, 4 to 20 mA Voltage Output: 10 mA (Max.) Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Load Resistor: • Internal power: 400 ohms • External 24V power: 1000 ohms RTD Input Type: PT50, PT100, PT200, PT500, PT1000; Resistance of 10 ohms, 20 ohms, and 100 ohms Sampling Rate: 12 samples/sec (all channels) Resolution: 16 bits Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Input Impedance: 625K ohms Thermocouple Input Sensor Type: J, K, T, E, R, S, B, N Mili Volt Type: ±78.126 mV, ±39.062 mV, ±19.532 mV Fault and Overvoltage protection: ±35 VDC (power off); +30 VDC, -25 VDC (power on) Sampling Rate: 12 samples/sec (all channels) Resolution: 16 bits Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Input Impedance: 10M ohms 3. Installation Power and Networking Connect the +12 to +36 VDC power line to the ioLogik E1200’s terminal block V+ terminal; connect the ground from the power supply to the V- terminal. Connect the ground pin ( ) if earth ground is available.

– 1 – – 2 – – 3 – - 4 - P/N: 1802012001013 ioLogik E1200 Series Quick Installation Guide Fourth Edition, April 2015 Overview The ioLogik E1200 series comes with 2 embedded Ethernet switch ports that can form a daisy-chain topology, which is the easiest way to add more Ethernet devices to a network or connect your ioLogiks in series. Moxa’s free Active OPC Server offers active (or “push”) communication that works between Moxa’s ioLogik units and HMI/SCADA systems, providing instant I/O status reports by “Active Tags.” The event-driven active tags result in an I/O response time that is faster than other OPC Server packages. Model Selection: ioLogik DI DO DIO Relay AI AO RTD TC E1210 16 - - - - - - - E1211 - 16 - - - - - - E1212 8 - 8 - - - - - E1213* 8 4 4 - - - - - E1214 6 - - 6 - - - - E1240 - - - - 8 - - - E1241 - - - - - 4 - - E1242 4 - 4 - 4 - - - E1260 - - - - - - 6 - E1262 - - - - - - - 8 *The ioLogik E1213 has source DOs. Package Checklist • 1 ioLogik E1200 series remote I/O product • Documentation and software CD • Quick installation guide (printed) Specifications System Ethernet: 2 x 10/100 Mbps switch ports, RJ45 Protection: 1.5 KV magnetic isolation Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP Power Input: 24 VDC nominal, 12 to 36 VDC Wiring: I/O cable max. 14 AWG Dimensions: 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) Weight: under 200 g Operating Temperature: Standard Models: -10 to 60°C (14 to 140°F) Operating Temperature: Wide Temperature Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Note: Contact Moxa if you require products guaranteed to function properly at higher altitudes. Standards and Certifications: UL 508, CE, FCC Class A Warranty Period: 5 years (excluding ioLogik E1214*) Details: See www.moxa.com/warranty *Because of the limited lifetime of power relay, products that use this component are covered by a 2-year warranty. Digital Input Sensor Type: NPN, PNP, and Dry contact I/O Mode: DI or Event Counter Dry Contact: • On: short to GND • Off: open Wet Contact (DI to COM): • On: 10 to 30 VDC • Off: 0 to 3 VDC Isolation: 3K VDC or 2K Vrms Counter/Frequency: 250 Hz, power off storage Digital Output (Sink) I/O Mode: DO or Pulse Output Pulse Wave Width/Frequency: 1 ms/500 Hz Over-voltage Protection: 45 VDC Over-current Protection: 2.6 A (4 channels @650 mA) Over-temperature Shutdown: 175°C (typical), 150°C (min.) Current Rating: 200 mA per channel Isolation: 3K VDC or 2K Vrms Digital Output (Source) I/O Mode: DO or Pulse Output I/O Type: Source Current: 0.5A per channel Voltage: For DIO channel: 15 to 30 VDC (ext power voltage) For DO channel: 15 to 30 VDC (ext power voltage), 12 or 9 VDC configurable by jumper. Pulse Wave Width/Frequency: 1 ms/500 Hz Over-voltage Protection: 41 VDC Over-current Limit: 6 A Over-temperature Shutdown: 175°C (typical), 150°C (min.) Output Current Rating: 1.5 A per channel Relay Output Type: Form A (N.O.) relay outputs, 5A Contact Rating: 5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110 VAC Inductance Load: 2 A Resistance Load: 5 A Breakdown Voltage: 500 VAC Relay On/Off Time: 1500 ms (max.) Initial Insulation Resistance: 1G min. @ 500 VDC Expected Life: 100,000 times (typical) Initial Contact Resistance: 30 milli-ohms (max.) Pulse Output: 0.3 Hz at rated load Analog Input Type: Differential input Resolution: 16 bits I/O Mode: Voltage / Current Input Range: 0 to 10 VDC, 4 to 20 mA Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -10 and 60°C ±0.5% FSR @ -40 and 75°C Sampling Rate (all channels): 12 samples/sec Input Impedance: 10M ohms (min.) Built-in Resistor for Current Input: 120 ohms Analog Output Resolution: 12 bits Output Range: 0 to 10 VDC, 4 to 20 mA Voltage Output: 10 mA (max.) Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Load Resistor: Internal register: 400 ohms Note: 24 V of external power is required when loading > 1000 ohms. RTD Input Type: PT50, PT100, PT200, PT500, PT1000 Resistance: 1–310, 1–620, 1–1250, 1–2200 ohms Sampling Rate: 12 samples/sec (all channels) Resolution: 16 bits Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Input Impedance: 625k ohms Thermocouple Input Sensor Type: J, K, T, E, R, S, B, N Millivolt Type: ±78.126 mV, ±39.062 mV, ±19.532 mV Fault and Overvoltage protection: ±35 VDC (power off); +30 VDC, -25 VDC (power on) Sampling Rate: 12 samples/sec (all channels) Resolution: 16 bits Accuracy: ±0.1% FSR @ 25°C ±0.3% FSR @ -40 and 75°C Input Impedance: 10M ohms Installation Connecting the Power Connect the +12 to +36 VDC power line to the ioLogik E1200’s terminal block V+ terminal; connect the ground from the power supply to the V- terminal. Connect the ground pin ( ) if earth ground is available. NOTE For safety reasons, wires connecting the power supply should be at least 2 mm in diameter (e.g., 12 gauge wires). Jumper Settings Models with DIO, AI, or external power channels require configuring the jumpers inside the enclosure. Remove the screw located on the back panel and open the cover to configure the jumpers. DIO mode configurations are shown above (Default: DO Mode). Analog mode configurations are shown above (Default: Voltage Mode). DOs on the ioLogik E1213 have 3 possible external (EXT) power configurations, which are shown to the right. Only one field power can be selected at a time (JP10 / 12V JP5 / 9V JP11) and the jumper must be inserted vertically, not horizontally (Default: Field Power JP10). NOTE The ioLogik E1213 has 4 pure DO channels and 4 hybrid DIO channels. For the 4 pure DO channels, you can use the jumpers to select the power configuration output (i.e., field power, 12 V, 9 V). But for the 4 hybrid DIO channels, you cannot use the jumpers to select the power configuration output. Instead, you can only use the jumpers to set the DIO channels to either DI mode or DO mode. Mounting There are two sliders on the back of the unit for DIN rail and wall mounting. 1. Mounting on a DIN rail: Pull out the bottom slider, latch the unit onto the DIN-rail, and push the slider back in. 2. Mounting on the wall: Pull out both the top and bottom sliders and align the screws accordingly.

ioLogik E1200 Series User’s Manual Second Edition, April 2010 www.moxa.com/product © 2010 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.

ioLogik E1200 Series User’s Manual Edition 12.0, October 2016 www.moxa.com/product © 2016 Moxa Inc. All rights reserved.

ioLogik E1200 Series User’s Manual Edition 15.4, October 2018 www.moxa.com/product © 2018 Moxa Inc. All rights reserved.

ioLogik E1200 Series Quick Installation Guide -Analog P/N: ������������� Second Edition. www.moxa.com ©2010 Moxa Inc. Moxa Inc. All rights reserve Pin Assignments ioLogik E1260 (top to bottom) ioLogik E1262 (top to bottom) 1 EX0 2 IN0+ 3 IN0- 4 EX1 5 IN1+ 6 IN1- 7 EX2 8 IN2+ 9 IN2- 10 EX3 11 IN3+ 12 IN3- 13 EX4 14 IN4+ 15 IN4- 16 EX5 17 IN5+ 18 IN5- 19 20 1 TC0+ 2 TC0- 3 TC1+ 4 TC1- 5 TC2+ 6 TC2- 7 TC3+ 8 TC3- 9 TC4+ 10 TC4- 11 TC5+ 12 TC5- 13 TC6+ 14 TC6- 15 TC7+ 16 TC7- 17 18 19 20 ioLogik E1241 (top to bottom) 1 VO0+ 2 VO0- 3 IO0+ 4 IO0- 5 VO1+ 6 VO1- 7 IO1+ 8 IO1- 9 VO2+ 10 VO2- 11 IO2+ 12 IO2- 13 VO3+ 14 VO3- 15 IO3+ 16 IO3- 17 18 19 EX_V 20 EX_C ioLogik E1242 (top to bottom) 1 AI0+ 2 AI0- 3 AI1+ 4 AI1- 5 AI2+ 6 AI2- 7 AI3+ 8 AI3- 9 COM0 10 DI0 11 DI1 12 DI2 13 DI3 14 GND 15 COM1 16 DIO0 17 DIO1 18 DIO2 19 DIO3 20 GND System Configuration Configuration via Web Console Main configuration of an ioLogik E1200 is via its web console. Default IP Address: 192.168.127.254 Subnet Mask: 255.255.255.0 Note: Be sure to configure the host PC’s IP address to the same subnet as the ioLogik E1200. For example, 192.168.127.253 ioSearch Utility ioSearch is a search utility that helps user locate an ioLogik E1200 on the local network. Find the ioSearch utility in the Document and Software CD \ Software \ ioSearch, or download the latest version on Moxa website. Load Factory Default There are three ways to restore the ioLogik E1200 to the factory default. 1. Hold the RESET button for 5 seconds. 2. Right click the specified ioLogik in the ioSearch utility and select “Reset to Default”. 3. Select the “Load Factory Default” at the web console. Modbus Address Table Please refer to the user’s manual for details of the ioLogik’s Modbus address, or refer to the start address of the I/O channels in web console � User-defined Modbus Addressing � Default Address. Active OPC Server Connection Refer to the following steps to connect the ioLogik E1200 to an Active OPC Server. 1. Disable the user-defined Modbus address function. 2. Install the Active OPC Server Lite Package from Document and Software CD � Software � AOPC Lite � ActiveOPCSetup � Install.exe 3. In web console � Active OPC Server Settings � AOPC & I/O Settings, specify the IP address where the Active OPC Server is installed. Specify the I/O channels that need to be added to the Active OPC Server Lite. Submit the settings and then Save/Restart. 4. In web console � Active OPC Server Settings � Create AOPC Tag, click the “Create Tag” button. 5. Launch the Active OPC Server Lite from Start � Programs � MOXA � IOServer � ActiveOPC � ActiveOPC. Save the configuration before exiting the Active OPC Server Lite program. ioLogik E1200 Series Remote Ethernet I/O with 2-port Ethernet Switch Overview The ioLogik E1200 series comes with 2 embedded Ethernet switch ports that can form a daisy-chain topology, which is the easiest way to add more Ethernet devices to a network or connect your ioLogiks in series. Moxa’s free Active OPC Server also offers active (or “push”) communication with Moxa’s ioLogik series of Ethernet I/O products for use with HMI/SCADA systems, providing instant I/O status reports by “Active Tags”. The event-driven active tags result in an I/O response time that is 7 times faster than other OPC Server packages. It also causes an apparent 80% reduction in network traffic. Model Selection: ioLogik AI AO DI DIO RTD TC E1241 -- 4 -- -- -- -- E1242 4 -- 4 4 -- -- E1260 -- -- -- -- 6 -- E1262 -- -- -- -- -- 8 Package Checklist � ioLogik E1200 � Documentation and Software CD � Quick Installation Guide Applications � Factory Facility Monitoring � Factory Environmental Monitoring � Remote Cabinet/Unmanned Site Monitoring � Lighting Control of Buildings � Machine Pre-installation Features � Built-in 2-port Ethernet switch for daisy-chain topologies � Free support of Moxa’s push-based Active OPC Server Lite • Seamlessly connect to any SCADA system • Save 80% on network bandwidth • I/O response that’s seven times faster � User-defined Modbus/TCP addressing � MXIO programming library for Windows and WinCE VB/VC.NET and Linux C APIs � Web configuration with Import/Export function› Specifications Network: � 2 x 10/100 Mbps switch ports, RJ45 � I/O Control: Modbus/TCP, OPC Server, MXIO(.NET) Library � Configuration: Web console, ioSearch utility System: � Power Input: 12 to 36 VDC � Power Consumption: 130 mA @ 24 VDC � Operating temperature: -10 to 60°C (32 to 140°F) � Ambient Relative Humidity: 5 to 95% � Dimensions: 27 × 132 × 84 mm � Housing: ABS + PC � Weight: 180 ± 10 g � UL508, CE, FCC Class A approval � Warranty: 5 years Digital Input: � Sensor Type: NPN, PNP, and Dry contact � I/O Mode: DI or Event Counter � Dry Contact Logic 0 short to GND; Logic 1: open � Wet Contact: • Logic 0: 0 to 3 VDC • Logic 1: 10 to 30 VDC (DI COM to DI) � Counter/Frequency: 250 Hz, power off storage Digital Output: � I/O Mode: DO or Pulse Output � Pulse Wave Width/Frequency: 500 Hz � Over-current Limit: 400 mA (typical)