Moxa Technologies UC-8410 Manuals

UC-8410/8416/8418 Hardware User’s Manual Second Edition, September 2009 www.moxa.com/product © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.

UC-8410A Hardware User’s Manual Edition 1.0, May 2016 www.moxa.com/product © 2016 Moxa Inc. All rights reserved.

– 1 – – 2 – – 3 – P/N: 1802084000013 UC-8410/8416/8418/8430 Quick Installation Guide Fifth Edition, March 2011 1. Overview The UC-8410/8416/8418/8430 embedded computers feature 8 RS-232/422/485 serial ports, 3 10/100 Mbps Ethernet ports, digital input and digital output channels, switch ports, CF and USB ports for storage expansion, and 2 VGA outputs (V8430 only). All of these features make the UC-8410/8416/8418/8430 computers ideal for your embedded applications. 2. Package Checklist • 1 UC-8410 or UC-8416 or UC-8418 or UC-8430 embedded computer • Wall-mounting kit • DIN-Rail mounting kit • Ethernet Cable: RJ45 to RJ45 cross-over cable, 100 cm • CBL-4PINDB9F-100: 4-pin pin header to DB9 female console port cable, 100 cm • Universal power adaptor (includes terminal block to power jack converter) • Quick installation guide (this guide) • Document and software CD • Warranty card Note: Please notify your sales representative if any of the above items are missing or damaged. 3. Panel Layout Refer to the following figures for the panel layouts. Front View UC-8410 UC-8416/8418 UC-8430 Rear View UC-8410 UC-8416 UC-8418 UC-8430 4. Installing the UC-8410/8416/8418/8430 Wall or Cabinet The two metal brackets included with the UC-8410/8416/8418/8430 can be used to attach it to a wall or the inside of a cabinet. Using two screws per bracket, first attach the brackets to the bottom of the UC-8410/8416/8418/8430. Next, use two screws per bracket to attach the UC-8410/8416/8418/8430 to a wall or cabinet. DIN-Rail Mounting The aluminum DIN-Rail attachment plate is included in the package. To attach the plate to the UC-8410/8416/8418/8430, situate the stiff metal spring towards the top. STEP 1: Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2: The DIN-Rail attachment unit will snap into place as shown below. To remove the UC-8410/8416/8418/8430 from the DIN-Rail, reverse Steps 1 and 2 above. 5. Connector Description Power Connector Connect the 12-48 VDC power line to the UC-8410/8416/8418/8430’s terminal block. The Ready LED will glow a steady green color when the OS is ready. Grounding the UC-8410/8416/8418/8430 Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting the power. ATTENTION This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel. SG: The Shielded Ground (sometimes called Protected Ground) contact is the right most contact of the 3-pin power terminal block connector when viewed from the angle shown here. Connect the SG wire to an appropriate grounded metal surface. Ethernet Port The 3 10/100 Mbps Ethernet ports (LAN 1, LAN 2, and LAN3), and 8 10/100 Mbps switch ports (UC-8416 only) use RJ45 connectors. Pin Signal 1 ETx+ 2 ETx- 3 ERx+ 6 ERx- VGA Connectors The MC-8430 comes with two D-Sub 15-pin female connectors to connect the VGA CRT monitors. Serial Port The 8 serial ports (P1 to P8) use RJ45 connectors. Each port can be configured by software as RS-232, RS-422, or RS-485. The pin assignments are shown in the following table (next page):

— 1 — — 2 — — 3 — UC-8410 Quick Installation Guide First Edition, October 2008 1. Overview The UC-8410 features 8 RS-232/422/485 serial ports, 3 10/100 Mbps Ethernet ports, 4 digital input and 4 digital output channels, and CompactFlash and USB ports for adding additional memory. All of these features make the UC-8410 ideal for your embedded applications. 2. Package Checklist Before installing the UC-8410, verify that the package contains the following items: y 1 UC-8410 embedded computer y Wall-Mounting Kit y DIN-Rail Mounting Kit y UC-8410 Quick Installation Guide (this guide) y UC-8410 Document & Software CD y Cross-over Ethernet cable y CBL-RJ45M9-150: 150 cm, 8-pin RJ45 to DB9 male serial port cable y CBL-4PINDB9F-150: 4-pin pin header to DB9 female console port cable, 150 cm y Universal power adaptor (includes terminal block to power jack converter) y Product Warranty Sheet Note: Please notify your sales representative if any of the above items are missing or damaged. 3. UC-8410 Panel Layout Refer to the following figures for UC-8410 panel layout. Rear View 10/100 Mbps Ethernet x 3 DI Channel x 4 DO Channel x 4 Power Input 12 to 48 VDC LED Indicators (Power, SRAM Battery, Ready, Storage) Top View Front View Serial Port x 8, RJ45 (RS-232/422/485) USB 2.0 Host x 2 Reset Button 4. Installing the UC-8410 Wall or Cabinet The two metal brackets included with the UC-8410 can be used to attach it to a wall or the inside of a cabinet. Using two screws per bracket, first attach the brackets to the bottom of the UC-8410. Next, use two screws per bracket to attach the UC-8410 to a wall or cabinet. DIN-Rail Mounting The aluminum DIN-Rail attachment plate is included in the package. To attach the plate to the UC-8410, situate the stiff metal spring towards the top. STEP 1: Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2: The DIN-Rail attachment unit will snap into place as shown below. metal spring DIN-Rail metal spring DIN-Rail To remove the UC-8410 from the DIN-Rail, reverse Steps 1 and 2 above. 5. Connector Description Power Connector Connect the 12-48 VDC power line to UC-8410’s terminal block. If the power is properly supplied, the Ready LED will glow a steady green color when the OS is ready. Grounding the UC-8410 Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting the power. ATTENTION This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel. SG SG: The Shielded Ground (sometimes called Protected Ground) contact is the left most contact of the 3-pin power terminal block connector when viewed from the angle shown here. Connect the SG wire to an appropriate grounded metal surface. Ethernet Port The 2 10/100 Mbps Ethernet ports (LAN 1 and LAN 2) use RJ45 connectors. Pin Signal 1 ETx+ 2 ETx- 3 ERx+ 6 ERx- 1 8 Serial Port The 8 serial ports (P1 to P8) use RJ45 connectors. Each port can be configured by software as RS-232, RS-422, or RS-485. The pin assignments are shown in the following table: Pin RS-232 RS-422/ RS-485-4W RS-485 1 DSR --- --- 2 RTS TXD+ --- 3 GND GND GND 4 TXD TXD- --- 5 RXD RXD+ Data+ 6 DCD RXD- Data- 7 CTS --- --- 8 DTR --- --- 1 8 P/N: 1802084000010

— 1 — — 2 — — 3 — UC-8410/8416/8418/8430 Quick Installation Guide Third Edition, August 2010 1. Overview The UC-8410/8416/8418/8430 embedded computers feature 8 RS-232/422/485 serial ports, 3 10/100 Mbps Ethernet ports, digital input and digital output channels, switch ports, CF and USB ports for storage expansion, and 2 VGA outputs (V8430 only). All of these features make the UC-8410/8416/8418/8430 computers ideal for your embedded applications. 2. Package Checklist � 1 UC-8410 or UC-8416 or UC-8418 or UC-8430 embedded computer � Wall-Mounting Kit � DIN-Rail Mounting Kit � Quick Installation Guide (this guide) � Document & Software CD � Ethernet cable: RJ45 to RJ45 cross-over cable, 100 cm � CBL-4PINDB9F-100: 4-pin pin header to DB9 female console port cable, 100 cm � Universal power adaptor (includes terminal block to power jack converter) � Product Warranty Sheet Note: Please notify your sales representative if any of the above items are missing or damaged. 3. Panel Layout Refer to the following figures for panel layout. Front View UC-8410 Serial Port x 8, RJ45 (RS-232/422/485) USB 2.0 Host x 2 Reset Button UC-8416/8418 Serial Port x 8, RJ45 (RS-232/422/485) USB 2.0 Host x 2 Reset Button CANbus Port x 2 DB9 (UC-8418) UC-8430 Serial Port x 8, RJ45 (RS-232/422/485) USB 2.0 Host x 2 Reset Button Rear View UC-8410 10/100 Mbps Ethernet x 3 DI Channel x 4 DO Channel x 4 Power Input 12 to 48 VDC LED Indicators (Power, SRAM Battery, Ready, Storage) UC-8416 10/100 Mbps Ethernet x 3 DO Channel x 4 Power Input 12 to 48 VDC LED Indicators (Power, SRAM Battery, Ready, Storage) DI Channel x 4 10/100 Mbps Ethernet Switch Port x 8 UC-8418 10/100 Mbps Ethernet x 3 DO Channel x 4 Power Input 12 to 48 VDC LED Indicators (Power, SRAM Battery, Ready, Storage) DI Channel x 4 DI Channel x 8 DO Channels x 8 UC-8430 USB 2.0 Host x 4 VGA Output x 2 10/100 Mbps LAN Port x 3, RJ45 Audio Output/Input DI x 4 DO x 4 Power Input LED Indicators (Power, Battery, Ready, Storage) 4. Installing the UC-8410/8416/8418/8430 Wall or Cabinet The two metal brackets included with the UC-8410/8416/8418/8430 can be used to attach it to a wall or the inside of a cabinet. Using two screws per bracket, first attach the brackets to the bottom of the UC-8410/8416/8418/8430. Next, use two screws per bracket to attach the UC-8410/8416/8418/8430 to a wall or cabinet. DIN-Rail Mounting The aluminum DIN-Rail attachment plate is included in the package. To attach the plate to the UC-8410/8416/8418/8430, situate the stiff metal spring towards the top. STEP 1: Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2: The DIN-Rail attachment unit will snap into place as shown below. metal spring DIN-Rail metal spring DIN-Rail To remove the UC-8410/8416/8418/8430 from the DIN-Rail, reverse Steps 1 and 2 above. 5. Connector Description Power Connector Connect the 12-48 VDC power line to UC-8410/8416/8418/8430’s terminal block. If the power is properly supplied, the Ready LED will glow a steady green color when the OS is ready. Grounding the UC-8410/8416/8418/8430 Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting the power. ATTENTION This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel. SG SG: The Shielded Ground (sometimes called Protected Ground) contact is the right most contact of the 3-pin power terminal block connector when viewed from the angle shown here. Connect the SG wire to an appropriate grounded metal surface. Ethernet Port The 3 10/100 Mbps Ethernet ports (LAN 1, LAN 2 and LAN3), and 8 10/100 Mbps switch ports (UC-8416 only) use RJ45 connectors. Pin Signal 1 ETx+ 2 ETx- 3 ERx+ 6 ERx- 1 8 P/N: 1802084000012