MXN MXN22CW Manuals

◈MXN22CW Camera ◈Installation ◈Features ◈Technical Specifications * Design And Specifications Are Subject To Change Without Notice. 1. Before making the connection, disconnect the ground terminal from the battery to avoid short circuits. 2. The plugs should be fully inserted into the connectors or jacks. A loose connection may cause malfunctioning of the unit. 3. A damaged cable may affect the operation of the camera and may even cause a malfunction of the camera or monitor: Avoid a damaged cable! 4. Protect the cable by using a guide tube, pipe or run the cable inside the vehicle as much as possible. Caution! Run the cable in natural shapes in order to prevent cable breaks. 5. Preferably use an acid free grease in between the waterproof screw type connectors and tighten them firmly eachother. ▪Caution !! ▪Securing cable connection Note! The warranty will not be valid if the problem is related to moist / corrosion in the connector. ▪Front View ▪Rear View Camera Bracket x 1 Manual x 1 Camera x 1 Screw kit x 1 IR LEDs Day/Night sensor 1. Match the arrow marks and press the connectors together. 2. Screw the camera connector up clockwise. 3. Tighten cable connection firmly in order to prevent water ingress. Instruction Manual 160 Degree Wide View, Autoheated, Color Camera MXN22CW ▪Camera Assembly 1. Fix the supplied camera bracket to the vehicle. 2. Fix the bracket with camera according to drawing. 3. Adjust the viewing angle of the camera and fasten the screws firmly. ▪Cable grommet Drill a suitable hole (approx. Ø 19mm) and insert the cable grommet. Just before final fixation, please apply a proper sealant (for prevention) between the hole and the grommet and also between the cable and the grommet. Built-in Microphone Normal/Mirror Image switch ◈Contents Image Sensor : 1/3.2” Color SONY CMOS (Exmor) Picture elements : PAL, 1.23 Mega pixels (1280 x 960) Resolution : 750 TV lines S/N ratio : Minimum 45dB (at AGC off) Minimum illumination : 0 Lux (IR LEDs on) Power range : DC 9 ~ 48V Power consumption : DC 12V, 265mA (heater on) DC 12V, 165mA (heater off) Operating temperature : -40ºC to +80ºC Viewing angle : 160˚(Diagonal) x 115˚(Horizontal) x 86˚(Vertical) Diameter, Dimensions : Ø52mm, 72(W) x 52(D) x 63(H) incl. bracket Weight : Supplied Accessories : Approx. 215g Camera Bracket (1) Stainless M6 x 25mm bolt + M6 nut (2 + 2) Stainless M3 x 12mm bolt + M3 nut (2 + 2) Stainless M4 x 16mm tapping screw (2) Rubber washer + stainless metal washer (2 + 2) Rubber O-Ring (2) Allen wrench 3mm (1) ▪High resolution CMOS, Compact Ball camera (1.23 Mega pixels) ▪1/3.2” Color CMOS high resolution image sensor ▪IP69K Waterproof Rating ▪Built-in Infra Red LEDs ▪IR LED ON/OFF function (via loop wire) ▪Diagonal 160˚ viewing angle ▪Normal/Mirror Image adjustable ▪Built-in Microphone (for one-way audio) ▪Multi purpose (Frontview, Sideview, Rearview, Surveillance, etc) ▪Built-in Automatic Heater (below +10˚C) ▪Anti-corrosive 3-fold coating ▪Temp. -40˚C ~ +80˚C ▪Vibration resistant (10G) ▪ECE R10.05 approved (EMC) ▪R46 and 2003/97/EC approved for indirect vision (with some specific MXN monitor models only) 10R-05-6368 E9 E4 S 044327 e4 S 03*4327 M3 bolt M6 nut Metal washer Rubber washer Rubber O-ring M3 nut M6 bolt Installation surface Ø6mm Drilling holes ▪Wiring to Monitor Run the cable from the camera to the monitor. * Green loop wire un-cut : IR LED function => ON / Standby * Green loop wire cut : IR LED function => permanent OFF IR LED function can be ON or OFF via the GREEN loop wire: ▪IR LED ON/OFF function Extension cable (Not supplied) Heater function (9~12V DC) Audio out Video out Power (9~48V DC) GROUND Camera pin configuration

◈ MXN22CW Camera ◈ Installation ◈ Features ◈ Technical Specifications * Design And Specifications Are Subject To Change Without Notice. 1. Before making the connection, disconnect the ground terminal from the battery to avoid short circuits. 2. The plugs should be fully inserted into the connectors or jacks. A loose connection may cause malfunctioning of the unit. 3. A damaged cable may affect the operation of the camera and may even cause a malfunction of the camera or monitor: Avoid a damaged cable! 4. Protect the cable by using a guide tube, pipe or run the cable inside the vehicle as much as possible. Caution! Run the cable in natural shapes in order to prevent cable breaks. 5. Preferably use an acid free grease in between the waterproof screw type connectors and tighten them firmly eachother. ▪ Caution !! ▪ Securing cable connection Note! The warranty will not be valid if the problem is related to moist / corrosion in the connector. ▪ Front View ▪ Rear View Camera Bracket x 1 Manual x 1 Camera x 1 Screw kit x 1 IR LEDs Day/Night sensor 1. Match the arrow marks and press the connectors together. 2. Screw the camera connector up clockwise. 3. Tighten cable connection firmly in order to prevent water ingress. Instruction Manual 160 Degree Wide View, Autoheated, Color Camera MXN22CW ▪ Camera Assembly 1. Fix the supplied camera bracket to the vehicle. 2. Fix the bracket with camera according to drawing. 3. Adjust the viewing angle of the camera and fasten the screws firmly. ▪ Cable grommet Drill a suitable hole (approx. Ø 19mm) and insert the cable grommet. Just before final fixation, please apply a proper sealant (for prevention) between the hole and the grommet and also between the cable and the grommet. Built-in Microphone Normal/Mirror Image switch ◈ Contents Image Sensor : 1/3.2” Color SONY CMOS (Exmor) Picture elements : PAL, 1.23 Mega pixels (1280 x 960) Resolution : 750 TV lines S/N ratio : Minimum 45dB (at AGC off) Minimum illumination : 0 Lux (IR LEDs on) Power range : DC 9 ~ 48V Power consumption : DC 12V, 265mA (heater on) DC 12V, 165mA (heater off) Operating temperature : -40ºC to +80ºC Viewing angle : 160˚(Diagonal) x 115˚(Horizontal) x 86˚(Vertical) Diameter, Dimensions : Ø52mm, 72(W) x 52(D) x 63(H) incl. bracket Weight : Supplied Accessories : Approx. 215g Camera Bracket (1) Stainless M6 x 25mm bolt + M6 nut (2 + 2) Stainless M3 x 12mm bolt + M3 nut (2 + 2) Stainless M4 x 16mm tapping screw (2) Rubber washer + stainless metal washer (2 + 2) Rubber O-Ring (2) Allen wrench 3mm (1) ▪ High resolution CMOS, Compact Ball camera (1.23 Mega pixels) ▪ 1/3.2” Color CMOS high resolution image sensor ▪ IP69K Waterproof Rating ▪ Built-in Infra Red LEDs ▪ IR LED ON/OFF function (via loop wire) ▪ Diagonal 160˚ viewing angle ▪ Normal/Mirror Image adjustable ▪ Built-in Microphone (for one-way audio) ▪ Multi purpose (Frontview, Sideview, Rearview, Surveillance, etc) ▪ Built-in Automatic Heater (below +10˚C) ▪ Anti-corrosive 3-fold coating ▪ Temp. -40˚C ~ +80˚C ▪ Vibration resistant (10G) ▪ ECE R10.05 approved (EMC) ▪ R46 and 2003/97/EC approved for indirect vision (with some specific MXN monitor models only) E9 10R-05-6368 E4 S 044327 e4 S 03*4327 M3 bolt M6 nut Metal washer Rubber washer Rubber O-ring M3 nut M6 bolt Installation surface Ø6mm Drilling holes ▪ Wiring to Monitor Run the cable from the camera to the monitor. * Green loop wire un-cut : IR LED function => ON / Standby * Green loop wire cut : IR LED function => permanent OFF IR LED function can be ON or OFF via the GREEN loop wire: ▪ IR LED ON/OFF function Extension cable (Not supplied) Heater function (9~12V DC) Audio out Video out Power (9~48V DC) GROUND Camera pin configuration