National Instruments NI cRIO-9111 Manuals

2 pdf manual(s) National Instruments NI cRIO-9111 for free download (Document Types: Operation & user’s manual, User manual and specifications)

National Instruments NI cRIO-9111 Operation & user’s manual [PDF] (6 pages)

  • Identifier: id-2155745
  • Brand: National Instruments
  • Device: NI cRIO-9111 Chassis
  • Type: PDF
  • Key Aspects: Critical Operational Precautions, Additional Modules and Accessories Guide, Safety Recommendations and Warnings
  • UPD Date: 13.04.2026
  • Source File: 2131890.pdf
  • Pages: 6
  • Description: Step-by-step user manual for the National Instruments NI cRIO-9111.
Pages Preview:
  • enter the Info Code rdcriotemp. Measure the ambient temperature at each side of the CompactRIO system, 63.5 mm (2.5 in.) from the side, and 25.4 mm (1 in.) from the rear cover of the system Ingress protection IP40 Operating humidity 10% RH to 90% RH, noncondensing Storage humidity 5% RH to 95% RH, noncondensing Pollution degree 2 Maximum altitude 5,000 m Indoor use only. Hazardous Locations Explosive atmospheres rating Ex nA IIC T4 Gc CCC certificate numbe
  • Caution Do not remove modules unless power has been switched off or the area is known to be nonhazardous. Caution Substitution of components may impair suitability for Zone 2. Caution You must make sure that transient disturbances do not exceed 140% of the rated voltage. Caution The system shall only be used in an area of not more than Pollution Degree 2, as defined in IEC/EN 60664-1. Caution The system shall be mounted in a CCC-certified enclosure wi
  • cRIO-9118 +5 V DC 500 mW maximum +3.3 V DC 5,400 mW maximum Total chassis power consumption 5,900 mW maximum Installing the Controller on the Chassis Complete the following steps to install the controller on the chassis. 1. Make sure that no power is connected to the controller or the chassis. 2. Align the controller with the chassis. 3. Slide the controller onto the controller slot on the chassis. Press firmly to ensure the chassis connector and the contr
  • cRIO-9111/9112/9113/9114/9116/9118 | © National Instruments Corporation | 5
Document Preview & Text Transcription (Main Page)
Click to expand and read text
EXPLOSIVE ATMOSPHERES USER GUIDE cRIO-9111/9112/9113/9114/ 9116/9118 cRIO-9111: 4-Slot, Virtex-5 LX30 FPGA CompactRIO Chassis (Legacy) cRIO-9112: 8-Slot, Virtex-5 LX30 FPGA CompactRIO Chassis (Legacy) cRIO-9113: 4-Slot, Virtex-5 LX50 FPGA CompactRIO Chassis (Legacy) cRIO-9114: 8-Slot, Virtex-5 LX50 FPGA CompactRIO Chassis (Legacy) cRIO-9116: 8-Slot, Virtex-5 LX85 FPGA CompactRIO Chassis (Legacy) cRIO-9118: 8-Slot, Virtex-5 LX110 FPGA CompactRIO Chassis (Legacy) Physical Characteristics Weight cRIO-9111 581 g (20 oz) cRIO-9112 880 g (31 oz) cRIO-9113 581 g (20 oz) cRIO-9114 880 g (31 oz) cRIO-9116 880 g (31 oz) cRIO-9118 880 g (31 oz) Dimensions Visit ni.com/dimensions and search by model number. Environmental Temperature Operating -40 °C to 70 °C Storage -40 °C to 85 °C Notice If the ambient temperature is 56 °C to 70 °C, you must mount the chassis on a thermally conductive material. For information about how mounting configuration can affect the accuracy of C Series modules, visit ni.com/info and

National Instruments NI cRIO-9111 User manual and specifications [PDF] (20 pages)

  • Identifier: id-1600024
  • Brand: National Instruments
  • Device: NI cRIO-9111 Chassis
  • Type: PDF
  • Key Aspects: Pre-Deployment Preparation Steps, Storage and Care Recommendations, Pre-Installation Safety Requirements
  • UPD Date: 17.07.2026
  • Source File: 1630301.pdf
  • Pages: 20
  • Description: Setup instructions for the National Instruments NI cRIO-9111.
Pages Preview:
  • Safety Guidelines for Hazardous Locations The chassis is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations; and nonhazardous locations only. Follow these guidelines if you are installing the chassis in a potentially explosive environment. Not following these guidelines may result in serious injury or death. Caution Do not disconnect I/O-side wires or conn
  • This product is intended for use in industrial locations. However, harmful interference may occur in some installations, when the product is connected to a peripheral device or test object, or if the product is used in residential or commercial areas. To minimize interference with radio and television reception and prevent unacceptable performance degradation, install and use this product in strict accordance with the instructions in the product documentat
  • What You Need to Start Using the CompactRIO System After you install the CompactRIO chassis, controller, and C Series modules, you need the following things to start using the CompactRIO system: • Windows computer with LabVIEW and NI-RIO software installed • ni.com/gettingstarted—learn how to install, set up, and configure your CompactRIO hardware and learn the basics of LabVIEW software. • LabVIEW Help—access information about LabVIEW programmin
  • Figure 2. Installing the Controller on the Chassis (Eight-Slot Chassis Shown) 1 4 3 5 2 1. Controller 2. Captive Screws 3. Controller Slot 4. Reconfigurable Embedded Chassis 5. Grounding Screw 3. Slide the controller onto the controller slot on the chassis. Press firmly to ensure the chassis connector and the controller connector are mated. 4. Using a number 2 Phillips screwdriver, tighten the two captive screws on the front of the controller to 1.3 N · m
  • configuration can affect the accuracy of C Series modules, go to ni.com/info and enter the info code rdcriotemp. Measure the ambient temperature at each side of the CompactRIO system, 63.5 mm (2.5 in.) from the side, and 25.4 mm (1 in.) from the rear cover of the system. Go to ni.com/info and enter the info code criomounting to learn more about the different mounting methods for CompactRIO. Before using any of the mounting methods, record the serial number
Document Preview & Text Transcription (Main Page)
Click to expand and read text
USER MANUAL AND SPECIFICATIONS NI cRIO-9111/9112/9113/9114/ 9116/9118 CompactRIO Reconfigurable Embedded Chassis Figure 1. CompactRIO Eight-Slot and Four-Slot Reconfigurable Embedded Systems 1 1 2 4 3 3 1. Controller 2. Eight-Slot Reconfigurable Embedded Chassis (cRIO-9112/9114/9116/9118) 3. C Series I/O Module 4. Four-Slot Reconfigurable Embedded Chassis (cRIO-9111/9113) This document describes how to install an NI cRIO-9111, cRIO-9112, cRIO-9113, cRIO-9114, cRIO-9116, or cRIO-9118. In this document the NI cRIO-9111, cRIO-9112, cRIO-9113, cRIO-9114, cRIO-9116, and cRIO-9118 are inclusively referred to as the cRIO-911x. Safety Guidelines Caution Do not operate the chassis in a manner not specified in this document. Product misuse can result in a hazard. You can compromise the safety protection built into the product if the product is damaged in any way. If the product is damaged, return it to NI for repair. all-guides com

National Instruments NI cRIO-9111: Chassis Category Related Instructions

EasyNote SW Series
Packard Bell EasyNote SW Series
16.04.2026 18 pages

Packard Bell EasyNote SW / W Series (Dragon, assorted platforms) Disassembly Manual Disclaimer: Note that this is a generic disassembly manual for the EasyNote SW & W series notebooks (assorted Dragon platforms). Actual notebooks might vary. Operating and setup manual for the Packard Bell EasyNote SW Series Laptop. This guide describes features and product handling, installation guides, performance optimization.

AER 43
WP AER 43
11.09.2026 32 pages

OWNER‘S MANUAL ART. NO. 53000130EN WWW.WP-GROUP.COM WP AER 43 CONE VALVE FORK Usage and setup manual for the WP AER 43 Chassis. The guide covers usage and hardware components, system checks, operational safety.

RSC-1R
AIC RSC-1R
09.08.2026 25 pages

UM_RSC-1R_v1.3_020521 RSC-1R Rackmount Chassis User's Manual Device instruction manual for the AIC RSC-1R Chassis. It describes step-by-step application scenarios, user preferences, product safety.

SC826BE1C-R920LPB
Supero SC826BE1C-R920LPB
11.06.2026 134 pages

SC826 SerieS ChaSSiS SUPER ® USer’S MaNUaL Revision 2.0 SC826BE1C-R920LPB SC826BE1C-R920WB SC826BE2C-R920LPB SC826BE2C-R920WB SC826BA-R1K28LPB SC826BA-R1K28WB SC826BE26-R1K28LPB SC826BE26-R1K28WB SC826BE16-R1K28LPB SC826BE16-R1K28WB SC826E26-R1200LPB SC82 Product manual for the Supero SC826BE1C-R920LPB Chassis. This manual explains technical assistance, replacement parts, power requirements.