National Instruments NI PXIe-5624R Manuals

GETTING STARTED GUIDE NI PXIe-5624R 2 GS/s, 12-Bit IF Digitizer Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the NI PXIe-5624R (NI 5624R). The NI 5624R is an IF digitizer with a user-programmable FPGA. The NI 5624R ships with NI LabVIEW Instrument Design Libraries for IF Digitizers, which you can use to program the device. Programming the NI 5624R requires NI LabVIEW. Customizing the FPGA requires the NI LabVIEW FPGA Module. To access NI 5624R documentation, navigate to Start»All Programs»National Instruments» IF Digitizers»IF Digitizers Documentation Note The NI 5624R can be used on its own or as a component of certain NI vector signal analyzers. Refer to the documentation for your vector signal analyzer for information about using the NI 5624R in an NI vector signal analyzer. Contents Electromagnetic Compatibility Guidelines...............................................................................2 Verifying the System Requirements......................................................................................... 2 Unpacking the Kit.....................................................................................................................2 NI 5624R Kit Contents..................................................................................................... 3 Preparing the Environment....................................................................................................... 4 Programming the NI 5624R......................................................................................................4 Installing the Software..............................................................................................................4 Installing the NI 5624R.............................................................................................................5 NI 5624R Front Panel.......................................................................................................8 Configuring the NI 5624R in MAX........................................................................................10 Self-Calibration.......................................................................................................................11 Making a Measurement with a Sample Project...................................................................... 11 Troubleshooting...................................................................................................................... 12 What Should I Do if the NI 5624R Doesn't Appear in MAX?.......................................12 What Should I Do if the Module Fails the Self-Test or Self-Calibration?......................12 Where to Go Next...................................................................................................................13 Worldwide Support and Services............................................................................................13 all-guide s.com Electromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits are designed to provide reasonable protection against harmful interference when the product is operated in the intended operational electromagnetic environment. This product is intended for use in industrial locations. However, harmful interference may occur in some installations, when the product is connected to a peripheral device or test object, or if the product is used in residential or commercial areas. To minimize interference with radio and television reception and prevent unacceptable performance degradation, install and use this product in strict accordance with the instructions in the product documentation. Furthermore, any modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules. Caution To ensure the specified EMC performance, operate this product only with shielded cables and accessories. Caution To ensure the specified EMC performance, the length of all I/O cables must be no longer than 3 m (10 ft). Verifying the System Requirements To use the NI 5624R, your system must meet certain requirements. For information about minimum system requirements, recommended system requirements, and supported ADEs, refer to the readme for the NI LabVIEW Instrument Design Libraries for IF Digitizers. When using the NI 5624R as a component of an NI vector signal analyzer, refer to the NI-RFSA Readme. Readmes are available on the driver software DVD and online at ni.com/updates. Unpacking the Kit Caution To prevent electrostatic discharge (ESD) from damaging the device, ground yourself using a grounding strap or by holding a grounded object, such as your computer chassis. 1. Touch the antistatic package to a metal part of the computer chassis. 2. Remove the device from the package and inspect the device for loose components or any other sign of damage. Caution Never touch the exposed pins of connectors. Notify NI if the device appears damaged in any way. Do not install a damaged device. 3. Unpack any other items and documentation from the kit. Store the device in the antistatic package when the device is not in use. 2 | ni.com | NI PXIe-5624R Getting Started Guide NI 5624R Kit Contents Figure 1. NI 5624R Kit Contents 1 2 3 4 5 1. NI PXIe-5624R IF Digitizer Module 2. Driver Software DVD 3. Read Me First: Safety and Electromagnetic Compatibility 4. Maintain Forced-Air Cooling Note to Users 5. NI 5624R Getting Started Guide (This Document) Other Equipment There are several required items not included in your device kit that you need to operate the NI 5624R. Your application may require additional items not included in your kit to install or operate your device. Required Items • A PXI Express chassis and chassis documentation. The NI PXIe-1085 chassis is one available option for your PXI Express device. For more information about compatible chassis options, visit ni.com/info and enter the Info Code pxiechassis. • A PXI Express embedded controller or PC with MXI controller system that meets the system requirements specified in this guide and chassis documentation. Optional Items • PXI Chassis Slot Blocker kit (NI part number 199198-01) • SMA (m)-to-SMA (m) cables • NI SHH19-H19-AUX DIGITAL I/O cable (NI part number 152629-01 or 152629-02) • NI SCB-19 DIGITAL I/O accessory for connecting to external signals (NI part number 782444-01) NI PXIe-5624R Getting Started Guide | © National Instruments | 3