Nav TV GVIF-CTS Manuals

BHM 11/01/18 NTV-DOC163 Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. 1 | P a g e 3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com [email protected] GVIF-CTS NTV-KIT201 Overview The GVIF-CTS Kit allows the user to add up to 3 video inputs and a backup camera input to the factory media screen in select GM vehicles. Audio integration requires that the vehicle have a factory audio input. Kit Contents AV Input Harness Power/CAN Harness GVIF Video cable GVIF-CTS Interface Remote RGB Input cable Input Toggle Switch IR Eye Harness BHM 11/01/18 NTV-DOC163 Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. 2 | P a g e Interface Connectors Dip Switch Settings* Configure prior to installation Dip SW: 1 2 3 4 5 6 7 8 UP Enables RGB Enables V1 Enables V2 Enables V3 Resolution adjust Keep UP Factory or no Rev-Cam N/A DOWN Skips RGB Skips V1 Skips V2 Skips V3 Resolution adjust Keep UP Activates aftermarket Rev-Cam N/A AV IN/OUT OUOUT Power/CAN OUOUT Dip Switches Status LEDs *Note: If the dip switches are not configured prior to installation you must remove power to the unit prior to making adjustments to the dip switches. When power is reconnected after the dip switch adjustment the new settings will be stored into memory. LCD IN/OUT (LVDS Cable) Touch IN/OU T OUOU T TX/RX BHM 11/01/18 NTV-DOC163 Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. 3 | P a g e OEM GVIF Radio Installation 1. Remove the factory radio. This usually requires pulling panels and removing a series of screws. Disconnect any associated harnesses and set the radio aside. 2. Gather the provided ‘Power/CAN Harness’ from the GVIF-CTS kit. Connect the following wires to the car: Note: CAN connection is not supported at this time. You must connect the GRAY wire to a reverse lamp for reverse activation! 3. Disconnect the factory GVIF cable from the factory radio, this is square, blue connector. 4. Connect the male side (labeled ‘LXIN’) of the provided GVIF video cable to the factory radio. 5. Connect the free end (removed in step 3) of the factory GVIF video cable to the female side of the provided GVIF video cable (labeled ‘LXOUT’). 6. Connect the white end of the GVIF video cable to the interface at the port labeled ‘LVDS IN/OUT’. 7. Connect the AV Input cable to the port on the GVIF-CTS interface labeled ‘AV IN/OUT’. If you’re only connecting a reverse camera (and no other inputs), the signal input from the camera must connect to the RCA labeled ‘REAR-C’. Refer to the dip- switch settings chart to skip/enable AV sources upon toggle switch presses (optional. Page 2). 8. Adjust dip switches on the GVIF-CTS interface properly, refer to the chart on page 2 for qualifications. 9. Connect the white plug from the ‘Power/CAN Harness’ to the port on the GVIF-CTS interface labeled ‘Power/CAN’. Interface wires Connect to car Black (GND) Chassis Ground Red (ACC) Accessory Gray (Rear) Reverse lamp 12v (Pin 2, Pink conn @ BCM) (only if adding rear camera) BHM 11/01/18 NTV-DOC163 Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. 4 | P a g e 10. Optional: Connect the remote eye to the port labeled ‘IR’ (on the power harness) and leave it in clear view of the driver (often it can be stuck inside a vent). This connection would be necessary if you want to be able to adjust anything from the GVIF-CTS interface’s menu. Refer to ‘Menu Adjustments’ for menu options. 11. Optional: Connect the provided momentary toggle switch to the port on the GVIF-CTS interface labeled ‘MODE’. Pressing this switch with the ignition on will cycle the screen modes as follows: factory screen > NAVI (RGB) > AV1 > AV2 > AV3 > factory screen. Please refer to the dipswitch section on page 2 for input settings. 12. Start the car and test for proper functionality before replacing dash pieces. 13. Note: All other included harnesses not mentioned in this manual are not needed for most installations. If you would like to know more about the full capability of this interface, contact NAV-TV tech support at 561-955-9770. Additional features not mentioned in this manual are not supported by NAV-TV at this time.

Jack Randall v1.2 July 13, 2012 1 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for rear camera use and the video input is for off-road use and passenger entertainment only. 100 NW 11th Street, Boca Raton, FL 33432 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com [email protected] GVIF-CTS Allows the addition of a rear camera and external video sources to a Cadillac CTS with a motorized screen. What’s in the box 1. Mode Switch 2. Remote Control 3. Power/CAN Harness 4. IR Receiver 5. AV Harness 6. GVIF Module 7. GVIF Cables Operation When used for a backup camera only, the module operates automatically when the vehicle is shifted into Reverse, and no user interaction is required. When used for Audio*/Video input, the supplied Mode button is used to switch between sources. * Note that this module is video only and does not provide an audio input. When adding one or more A/V sources, the audio input will be through the vehicle’s Aux jack. (If installing multiple A/V sources, use the A/V Out RCA’s of the module, if only a single audio source is being added, connect the audio source directly to the jack.) Jack Randall v1.2 July 13, 2012 2 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for rear camera use and the video input is for off-road use and passenger entertainment only. Installation 1. Using a plastic pry tool, remove the trim panel that goes across the dash. 2. With the plastic pry tool, pry up the (2) trim panels around the gear selector panel. 3. Place the vehicle into “Drive”, DO NOT START VEHICLE. Pull up the gear selector panel and pull up around the shifter. 4. Remove the (2) 7mm screws from around the radio/HVAC panel, then gently pry around the panel to remove. 5. Disconnect the trim panel wiring and cigarette lighter plug. 6. Remove the (4) 7mm screws from around the radio and remove the radio. 7. Locate the factory GVIF cable (square, Light Blue connector, which looks like it has a USB plug inside) and remove it. 8. Note the GVIF cables from the Nav-TV module have one that goes to the radio and another that goes to the cable. 9. Connect the wiring from the GVIF module to the factory cable and radio. 10. Connect the following wires on the Power/CAN harness: a. Red wire (12v Accessory): pin 21 (Brown) of Light Green connector of the BCM. b. Black wire (Ground): connect to chassis ground. c. Gray wire (Camera/Reverse trigger): pin 2 (Light Green) of the Pink connector of the BCM. (Optional: only when installing camera.) (BCM is located above the gas pedal.) 11. Make all necessary A/V connections. 12. If only adding a camera, set Dipswitches 1 and 7 Down, and the rest Up. 13. Test system. The audio is connected either behind radio or at the AUX jack. All other wires on module are not used. Remove 7mm