Nav TV RGB-VWv2 Manuals

BHM 01/04/19 NTV-DOC339 1 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. RGB Power Harness NTV-HAR324 Remote Control NTV-REM004 3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com [email protected] RGB-VWv2 NTV-KIT906 Overview The RGB-VWv2 adds an aftermarket backup camera to the factory navigation screen in select Volkswagen vehicles. A secondary video input is included on the RGB module and can be viewed at any time by supplying power to an input wire (optional). Kit Content RGB-VWv2 Video Harness NTV-HAR335 RGB Converter NTV-ASY254 BHM 01/04/19 NTV-DOC339 2 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. Power Harness RGB Video Harness Wire Side Wire Side RGB-VWv2 Interface Connectors RGB-VWv2 Pin Out PIN # Description Color 1 Ground (-) Black 2 INPUT 2 (AUX VIDEO) White/Blue 3 Shield (VIDEO 2) Black 4 Signal (VIDEO 2) Yellow 5 12v (+) ACC IN Red 6 INTPUT 1 (CAM VIDEO) White/Red 7 Shield (VIDEO 1) Black 8 Signal (VIDEO 1) Yellow PIN # Description Color 1 RGB Ground Black/Shield 2 SYNC (screen) Gray 3 Blue Signal (screen) Blue 4 Red Signal (screen) Red 5 Green Signal (screen) Green 6 RGB Ground Shield 7 SYNC (radio/NAV) Brown 8 Blue Signal (radio/NAV) Purple 9 Red Signal (radio/NAV) Orange 10 Green Signal (radio/NAV) Yellow IR Receiver RGBS wires IN & OUT Power, Video IN & triggers LED status Brightness buttons BHM 01/04/19 NTV-DOC339 3 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. RGB-VWv2 Installation 1. Remove the factory RNS navigation radio from the dash. 2. Connect the provided RGB-VWv2 harness to the RGB connector on the RNS radio. 3. Connect the other end of the harness to the RGBv2 module at the 10-PIN connector. RGB-VWv2 Power Connections 1. From the provided RGB Power Harness, connect the black wire to chassis ground (-) and the red wire with the white/blue wire to an ACC 12v (+) source (cigarette lighter, etc). 2. For VW, the reverse sensing is automatic through the radio. The VIDEO 2 RCA input must be used for camera signal. NOTE: VW’s have no option for adding a secondary (AUX) video source. NOTE: VW’s must be programmed for reverse camera with a VAG-COMM (Ross Tech) in order to use this harness. BHM 01/04/19 NTV-DOC339 4 | P a g e Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only. RGB-VWv2 Remote Control / Brightness Setting • The RGBv2 uses a (provided) remote for the following optional adjustments: o Arrow keys adjust (shifts) VIDEO 1 or 2 image LEFT, RIGHT, UP & DOWN (OEM pass through image is not adjustable) o Zoom/Page arrows adjust brightness o Pressing MENU>MAP>BACK (in order) will default all settings. • To adjust brightness of VIDEO 1 or 2 image, use the buttons on the RGB side of the module and adjust to suit. NOTE: when completing install, mount the RGBv2 module so that the buttons are not being pressed. RGB-VWv2 Operation After all connections are properly made: • When the vehicle is placed into reverse (white/red wire on the interface receives 12v +), the navigation screen will switch to Video 1 source (reverse camera). • In any other gear (but reverse) toggling the white/blue wire (12v (+) to the white/blue wire) will switch the factory navigation screen to Video 2 source*.