NEC Express5800 120Bb-m6 Manuals

Express5800/120Bb-6 STANDARD BlADE SERvER Key Benefits Highly modular Blade system » Industry leading design optimized for virtualization » Reduced power consumption » Key Features » Quad-Core Intel ® Xeon® Processors Up to 32GB of Memory » Two 1000Base-X Ports » Two Hot-Plug 2.5” SAS Hard Disk Bays » Supports RAID 0, RAID 1 & RAID 5 » Servers for Data Center Consolidation and Virtualization IT managers are facing infrastructure challenges that include costs, energy, change and productivity. NEC Express5800 Blade servers provide a versatile infrastructure to quickly deliver services to your business. NEC Express5800 Sigmablade Servers systems contain server, storage and network components in a cost-effective design. The management of blade servers is far easier than traditional rack-mount servers, the density is greater and the power consumption much lower.

Preface Unpack the carton box and make sure that you have everything and that individual components are not damaged. See the attached packing list. The "NEC EXPRESSBUILDER" DVD is to be used when setting up (or resetting up) your server, therefore store them in a designated place. We recommend you to print out the "User's Guide" stored in the "NEC EXPRESSBUILDER" DVD and read it along with this guide before setting up your server. See the "NEC EXPRESSBUILDER" on the rear face of this guide. Blade Enclosure The blade enclosure is the rack mount chassis exclusively used to be equipped with CPU blades and power supply unit. The blade enclosure is installed in the NEC rack or NEC-recommended rack conforming to the EIA standard. Refer to blade enclosure User's Guide for detail. Refer to the following items of the User’s Guide and follow the instructions for your safety to setup the server: "SYMBOLS USED IN THIS USER’S GUIDE AND WARNING LABELS" and "SAFETY INDICATION" Do not disconnect/connect the power plug while your hands are wet. Failure to follow this warning may cause an electric shock. Make sure to power off the CPU blade and take out the CPU blade from the blade enclosure before installing/removing internal optional devices. If it starts thundering, do not touch any part of the server including the cables. Failure to follow this warning may cause an electric shock. Never attempt to disassemble, repair, or alter the server on any occasion other than described in this User's Guide. At least four persons are required to carry the blade enclosure. Firmly hold the handle on the blade enclosure while carrying the blade enclosure. Do not install the server in dusty, humid, smoke or oily place. Also avoid installing the server in a place exposed to direct sunlight. Use the power cord that comes with your blade enclosure or NEC-specified power cord. Plug in to a proper power source. Do not install the enclosure where you need an extension cord. CPU Blade The CPU blade can be equipped with memory module and additional board. Refer to Chapter 2 of the User's Guide stored in DVD-ROM. Hard Disk Drive Up to six hard disk drives can be connected to a CPU blade. Each drive must be installed in a drive carrier. (To order a disk with a carrier, contact your sales representative or dealer.) 856-126393-522-00 Rev.01, 4-2008 Read this Guide First. Getting Started describes the procedures necessary for running the server after you unpack the product. Follow these steps to complete your installation successfully. Go on to the next page. POWER switch DUMP switch RESET switch LAN3 Link/Access lamp (green) LAN4 Link/Access lamp (green) SUV connector ID switch ID lamp(blue) STATUS lamp(green/amber/red) POWER lamp (green/amber) 1 5 Cable Connection The keyboard, mouse, display unit, and network devices are connected to t Connector board in the blade enclosure that is connected with the MP connect at the rear of the blade enclosure. Refer to Chapter 2 of the User's Guide stored in DVD-ROM. For options, refer to Chapter 9 of the User's Guide stored in the provided DVD- ROM. Installing Options Install the optional devices required for the CPU blade and the blade enclosur Finally, connect the power cord coming with the power supply unit to the AC in of power supply unit at the rear of the blade enclosure and the AC outlet for 20 240 VAC. The power cord coming with the power supply unit can be exclusively used for the 200-240 VAC power. Connect the power cord only to an AC outlet for 200-240 VAC. Keep the removed slot cover for future use. Do not remove the slot cover from any other slot. The CPU blade can be installed in the following slots of Blade Enclosure(SIGMABLADE-M). － Slots 1 and 2 － Slots 3 and 4 － Slots 5 and 6 － Slots 7 and 8 Diskless model Model Prepare the hard disk drive and operating system separately. Refer to blade enclosure User’s Guide for detail. (2) Gently put the CPU blade on the clean, rigid, and flat desk. Loosen the screw of the ejector to allow the ejector to be opened. (3) Hold the frame of the CPU blade so that its MP connector faces the Blade Enclosure and the hard disk drive downward. (5) Firmly push in the ejector of the CPU blade, and push the frame at the front of the blade enclosure. Then, tighten the screw of the ejector to fix the CPU blade to the blade enclosure. Do not hold the ejector to install the CPU blade in the Blade Enclosure. The ejector may be disengaged from the CPU blade that causes the CPU blade to fall down. Or, the ejector may be bent that causes damage to the CPU blade. (1) If an optional slot cover is installed on the slot on which the CPU blade is to be installed, remove it. Unlock the CPU blade by holding the lever at the front, pull out the CPU blade, and then remove the slot cover. Make sure that the blade enclosure does not contain any CPU blade. Install the blade enclosure in the rack. Then, install the CPU blade in the blade enclosure. 1. To install a hard disk drive in the slot 1 and the subsequent slot, remove a hard disk tray from the slot to install a hard disk drive. The SUV connector on the front of the CPU blade is not used in normal operatio Use the SUV connector in the following cases: ⓦ Installing OS (when the CPU blade is installed in blade enclosure(10U)) ⓦ Maintenance ⓦ Updating BIOS and firmware Connect the K410-150(00) SUV cable (separately priced, or provided with the Blade Enclosure) to the SUV connector. Then, connect peripheral devices to the connectors of SUV cable. * When you use the N8460-009 external DVD-ROM drive, use the branch USB cable provided with the CPU blade. 2. Release the lock of the lever on the hard disk drive to make the lever opened. Keep the removed hard disk tray for future use. 3. Hold the hard disk drive so that the BP connector faces the storage unit and the lever on the front of the drive carrier faces the top. 4. Insert the end of the drive carrier into the hard disk drive slot slowly and carefully. 5. Insert the drive carrier until it hits the slot end, and lift the lever. Make sure that the hook below the lever is hung on the frame. Eject lever Lever Make sure that the ejector hook is hit to the frame of the blade enclosure, as shown in the figure. Ejector Mouse Keyboard Monitor (4) Align the frame of the CPU blade with the guide rails of the blade enclosure, and insert the CPU blade into the end of blade enclosure slowly and carefully. LAN1 Link/Access lamp (green) LAN2 Link/Access lamp (green) CPU blade External DVD-ROM drive* Keyboard Mouse External floppy disk drive USB USB Self-powerd USB hub Monitor Slot 0 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Frame Ejector hook

NEC Express5800/BladeServer Series N8400-071AF/072AF/073AF/074AF NEC Express5800/120Bb-m6 User's Guide 1st Edition 4-2008 ONL-540_001_01-120Bb-m6-100-99-0803 456-01752-000 PN# 456-01752-000