Neopost IS-280 Manuals

Internet Install Guide Postage Meter IS-280 iMeter™ • Use a wall outlet located near the equipment. Do not route the power cord between pieces of furniture or over sharp edges. • Make sure there is no strain on the power supply cord. • Avoid using outlets controlled by wall switches or shared by other equipment. • To reduce the risk of fire, use only the power cord supplied with the IS-280 iMeter™. • Do not use this product on a wet floor or near water. • In the case of liquid spillage, disconnect the external power supply from the wall outlet prior to cleaning. GENERAL SAFETY • Before using your IS-280 iMeter™, thoroughly read the operating instructions. • To reduce the risk of fire, electric shock and injury to persons, follow normal and basic safety precautions for office equipment when using your IS-280 iMeter™. • To avoid equipment damage, only use approved supplies (ink, tapes, cleaners...). The IS-280 iMeter™ contains moving parts. Keep fingers, long hair, neck ties, and loose clothing away from the mail path at all times. FOLLOW THE ADDITIONAL SAFETY PRECAUTIONS BELOW: • Do not place lighted candles, cigarettes, cigars, etc. on the IS-280 iMeter™. • When lifting covers, wait for all parts to stop moving before placing hands near the ink cartridge assembly. • When changing internal (ink, postage meter...), avoid using too much force to prevent personal injury or damaging equipment. • To prevent overheating, do not block the equipment ventilation openings. • Do not remove bolted covers as they enclose potentially hazardous parts that should only be accessed by a Service Representative. ADDITIONAL SAFETY PRECAUTIONS • Power is supplied to the unit when it is connected to an electrical outlet, even if the unit is turned off or in sleep mode. • Disconnect the wall plug to remove power from the unit. • DO NOT make any changes or modifications to this equipment. • Use only the Neopost/Hasler supplied USB, Internet/LAN, or modem cables. • This equipment is NOT user-serviceable. If you have any problems with the equipment contact customer service. • If you have alarm equipment connected to the telephone line, check first with the telephone company or a qualified installer to confirm that connection of this equipment to your telephone line does not disable the alarm equipment. YOUR IS-280 IMETER™ SHOULD ONLY BE OPERATED IN THE FOLLOWING CONDITIONS: • Temperature range: 50°F - 104°F (10°C - 40°C). • Relative humidity: 80% maximum without condensation. SAFETY REQUIREMENTS ! ! CONTENTS Not needed for this connection type IS-280 iMeter™ Scale Internet Cable Postage Meter USB Cable Ink Cartridge Power Supply AC Power Cord

modem install guide is-280 imeter™ Postage meter safety requirements •� Use�a�wall�outlet�located�near�the�equipment.�Do�not�route�the�power�cord�between�pieces�of�furniture�or�over�sharp�edges. •� Make�sure�there�is�no�strain�on�the�power�supply�cord. •� Avoid�using�outlets�controlled�by�wall�switches�or�share�by�other�equipment. •� To�reduce�the�risk�of�fire,�use�only�the�power�cord�supplied�with�the�IS-280�iMeter™. •� Do�not�use�this�product�on�a�wet�floor�or�near�water. •� In�the�case�of�liquid�spillage,�disconnect�the�external�power�supply�from�the�wall�outlet�prior�to�cleaning. General Safety •� Before�using�your�IS-280�iMeter™,�thoroughly�read�the�operating�instructions. •� To�reduce�the�risk�of�fire,�electric�shock�and�injury�to�persons,�follow�normal�and�basic�safety�precautions�for�office�equipment�when�using�your�IS-280�iMeter™. •� To�avoid�equipment�damage,�only�use�approved�supplies�(ink,�tapes,�cleaners...). The�IS-280�iMeter™�contains�moving�parts.�Keep�fingers,�long�hair,�neck�ties,�and�loose�clothing�away�from�the�mail�path�at�all�times. follow the additional Safety precautionS below: •� Do�not�place�lighted�candles,�cigarettes,�cigars,�etc.�on�the�IS-280�iMeter™. •� When�lifting�covers,�wait�for�all�parts�to�stop�moving�before�placing�hands�near�the�ink�cartridge�assembly. •� When�changing�internal�(ink,�postage�meter...),�avoid�using�too�much�force�to�prevent�personal�injury�or�damaging�equipment.� •� To�prevent�overheating,�do�not�block�the�equipment�ventilation�openings. •� Do�not�remove�bolted�covers�as�they�enclose�potentially�hazardous�parts�that�should�only�be�accessed�by�a�Service�Representative. additional Safety precautionS •� Power�is�supplied�to�the�unit�when�it�is�connected�to�an�electrical�outlet,�even�if�the�unit�is�turned�off�or�in�sleep�mode. •� Disconnect�the�wall�plug�to�remove�power�from�the�unit. •� DO�NOT�make�any�changes�or�modifications�to�this�equipment. •� Use�only�the�Neopost/Hasler�supplied�USB,�Internet/LAN,�or�modem�cables. •� This�equipment�is�NOT�user-serviceable.�If�you�have�any�problems�with�the�equipment�contact�customer�service. •� If�you�have�alarm�equipment�connected�to�the�telephone�line,�check�first�with�the�telephone�company�or�a�qualified�installer�to�confirm�that�connection�of�this�equipment�to�your�telephone� line�does�not�disable�the�alarm�equipment. your iS-280 iMeter™ Should only be operated in the followinG conditionS: •� Temperature�range:�50°F�-�104°F�(10°C�-�40°C). •� Relative�humidity:�80%�maximum�without�condensation. Contents IS-280�iMeter™ Scale Internet�Cable Ink�Cartridge Postage�Meter USB�Cable� not needed for this connection type Phone�Cord�and�USB�Modem and Power�Supply�and�AC�Power�Cord and 1 steP 1 install Postage meter place the iS-280 on its back and open the bottom postage meter cover. B remove the postage meter from the packaging. Write�down�the�serial�number�and� store�it�in�a�safe�place.�You�will�need�to� reference�the�serial�number�if�support� is�needed. a insert the postage meter into the iS-280. 1.�Insert�with�the�labels�facing� outward�and�with�the�connection� on�the�bottom.� 2.�Make�sure�that�the�postage�meter� clicks/locks�into�place. 3.�Close�the�postage�meter�cover. C

© 2011 Neopost USA Inc. All rights reserved. No part of this document may be reproduced or distributed in any form or by any means. IS / IM280 iMeter™ Postage Meter Replacement Part Guide PSD (Meter) & Base For interactive step by step instructions, visit: www.neopostinc.com/280helpdesk (For Neopost Customers) www.haslerinc.com/280helpdesk (For Hasler Customers) To replace the PSD (Meter) only, please go to page 1 – PSD (Meter) Replacement. PSD In The Shipping Box PSD Without The Shipping Box To replace the Base only, please go to page 5 – Base Replacement. IS / IM280 iMeter™ Base © 2011 Neopost USA Inc. All rights reserved. No part of this document may be reproduced or distributed in any form or by any means. PSD pg 1 PSD (Meter) Replacement The following steps will guide you through the removal of the PSD (Postal Security Device) and installation of a new PSD (Meter). Replacing The PSD PSD Components The following steps are performed when the PSD needs to be replaced. 1. Withdrawing the PSD. 2. Installing the new PSD into to system. 3. Returning the old PSD. 4. Swapping the PSD. Withdrawing The PSD 1. Press the Sleep/Wake button. The power indicator light will become green. 6. Press the down arrow button to select “Maintenance”. Press “OK”. 2. From the Homescreen, press the “MENU” button. 7. Press the down arrow button to select “Processes”. Press “OK”. 3. Press the down arrow button until “Supervisor” is highlighted. 8. Press “OK” to continue with this process. 4. Once “Supervisor” is highlighted, press “OK”. 9. Press the down arrow button to select “Withdraw PSD”. Press “OK”. 5. Enter the Supervisor PIN code, “09430”. 10. Press “Next” to continue to withdraw the meter (PSD). IS / IM280 iMeter™ Postage Meter PSD