Command reference manual [PDF] (148 pages)
- Brand: Net2Phone
- Model: Max 8
- Format: PDF
- Key Aspects: Recommended Spare Parts List, Troubleshooting Information, Information on Regular Maintenance
- Updated: 27.08.2026
- Source File: 907120.pdf
- Pages: 148
- Description: User support manual for the Net2Phone Max 8.
Document Preview & Text Transcription
Command Reference
Guide
for configuration management of
MAX systems through a
serial connection
Version 1.0
MAX 8/16
MAX 8
and
MAX 8/16
TM
TM
ii
The specifications and information regarding the products in this manual are subject to change without
notice. All statements, information, and recommendations in this manual are believed to be accurate but
are presented without warranty of any kind, express or implied. Users must take full responsibility for their
application of any products.
The software license and limited warranty for the accompanying product are set forth in the information
packet that shipped with the product and are incorporated herein by this reference. If you are unable to
locate the software license or limited warranty, contact your Net2Phone representative for a copy.
The following information is for FCC compliance of Class A devices: This equipment has been tested and
found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this
manual generates and may radiate radio-frequency energy. If it is not installed in accordance with
Net2Phone's installation instructions, it may cause interference with radio and television reception. This
equipment has been tested and found to comply with the limits for a Class B digital device in accordance
with the specifications in part 15 of the FCC rules. These specifications are designed to provide
reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation.
Modifying the equipment without Net2Phone's written authorization may result in the equipment no longer
complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference
stops, it was probably caused by the Net2Phone equipment or one of its peripheral devices. If the
equipment causes interference to radio or television reception, try to correct the interference by using one
or more of the following measures:
· Turn the television or radio antenna until the interference stops.
· Move the equipment to one side or the other of the television or radio.
· Move the equipment farther away from the television or radio.
· Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is,
make certain the equipment and the television or radio are on circuits controlled by different circuit
breakers or fuses.)
Modifications to this product not authorized by Net2Phone could void the FCC approval and negate your
authority to operate the product.
Notwithstanding any other warranty herein, all document files and software of these suppliers are provided
"as is" with all faults. Net2Phone and the above-named suppliers disclaim all warranties, expressed
or implied, including, without limitation, those of merchantability, fitness for a particular purpose and non-
infringement or arising from a course of dealing, usage, or trade practice.
In no event shall Net2Phone or its suppliers be liable for any indirect, special, consequential, or incidental
damages, including, without limitation, lost profits or loss or damage to data arising out of the use or
inability to use this manual, even if Net2Phone or its suppliers have been advised of the possibility of such
damages.
Net2Phone, MAX 8, MAX 8/16, net2phone, and the Net2Phone logo are registered trademarks of
Net2Phone, Inc. in the US and certain other countries. All other trademarks mentioned in this document
are the property of their respective owners.
Net2Phone MAX 8 and MAX 8/16 Command Reference Guide
Rev. 1.0 July 2001
Copyright © 2001, Net2Phone, Inc. All Rights Reserved
The use, disclosure, modification, transfer, or transmittal of this work for any purpose, in any form, or by
any means, without the written permission of Net2Phone, is strictly forbidden.
Printed in Korea
iii
Table of Contents
INTRODUCTION.......................................................................................................................................... 1
Conventions Used in this Guide .......................................................................................................... 1
About Console Commands ................................................................................................................. 1
Basic Command Line Navigation ........................................................................................................ 1
1. BASIC COMMANDS................................................................................................................................ 3
1.1
Dir (or LS) ................................................................................................................................. 4
1.2
CD............................................................................................................................................. 5
1.3
Help........................................................................................................................................... 6
2. SYSTEM COMMANDS............................................................................................................................ 7
2.1
Reset......................................................................................................................................... 8
2.2
Date [yyyy-mm-dd].................................................................................................................... 9
2.3
Time [hh:mm:ss]..................................................................................................................... 10
2.4
Password .......................................................................................................... 11
2.5
Sysname [system name]......................................................................................................... 12
2.6
Versioninfo .............................................................................................................................. 13
2.7
Slotinfo.................................................................................................................................... 14
3. CONFIGURATION MANAGEMENT COMMANDS................................................................................ 16
3.1
Default..................................................................................................................................... 17
3.2
Load........................................................................................................................................ 19
3.3
Save........................................................................................................................................ 20
4. SYSTEM CONFIGURATION COMMANDS........................................................................................... 21
4.1
Show....................................................................................................................................... 22
4.2
Change [parameter][value]...................................................................................................... 23
5. IP CONFIGURATION COMMANDS ...................................................................................................... 24
5.1
Show....................................................................................................................................... 25
5.2
Change ................................................................................................................................... 26
6. ROUTING TABLE CONFIGURATION COMMANDS............................................................................. 32
6.1
Show....................................................................................................................................... 33
6.2
Add.......................................................................................................................................... 34
6.3
Del........................................................................................................................................... 36
7. NET2PHONE (N2P) PROTOCOL CONFIGURATION COMMANDS .................................................... 38
7.1
Show....................................................................................................................................... 39
7.2
Change ................................................................................................................................... 40
8. ADDRESS CONFIGURATION COMMANDS ........................................................................................ 42
8.1
Show....................................................................................................................................... 43
8.2
Myaddr.................................................................................................................................... 44
8.3
Peeraddr (not applicable to Net2Phone MAX 8) .................................................................... 46
8.4
Gport....................................................................................................................................... 49
9. DSP CONFIGURATION COMMANDS .................................................................................................. 50
9.1
Show....................................................................................................................................... 51
9.2
Change ................................................................................................................................... 52
10. FXS CONFIGURATION COMMANDS ................................................................................................ 55
10.1
Show....................................................................................................................................... 56
10.2
Change ................................................................................................................................... 57
11. FXO CONFIGURATION COMMANDS................................................................................................ 59
11.1
Show...................................................................................................................................... 60
11.2
Change .................................................................................................................................. 61
iv
12. DIGITAL TRUNK CONFIGURATION COMMANDS............................................................................ 63
12.1
Show....................................................................................................................................... 64
12.2
Change ................................................................................................................................... 65
13.
R2 CONFIGURATION COMMANDS.................................................................................................. 69
13.1
Show....................................................................................................................................... 70
13.2
Change ................................................................................................................................... 71
14. SYSTEM CALL STATISTICS DISPLAY COMMANDS........................................................................ 75
14.1
Show....................................................................................................................................... 76
14.2
Clear ....................................................................................................................................... 77
15.
FXS STATISTICS DISPLAY COMMANDS ........................................................................................ 78
15.1
Show....................................................................................................................................... 79
15.2
Clear ....................................................................................................................................... 80
16.
FXO STATISTICS DISPLAY COMMANDS........................................................................................ 81
16.1
Show....................................................................................................................................... 82
16.2
Clear ....................................................................................................................................... 83
17.
DIGITAL TRUNK STATISTICS DISPLAY COMMANDS .................................................................... 84
17.1
Show....................................................................................................................................... 85
17.2
Clear ....................................................................................................................................... 86
18.
R2 STATISTICS DISPLAY COMMANDS........................................................................................... 87
18.1
Show....................................................................................................................................... 88
18.2
Clear ....................................................................................................................................... 89
19. NET2PHONE PROTOCOL TEST COMMANDS ................................................................................. 90
19.1
Trace....................................................................................................................................... 91
19.2
Ologin...................................................................................................................................... 92
19.3
Ologout ................................................................................................................................... 93
19.4
Cstate...................................................................................................................................... 94
19.5
Ostate ..................................................................................................................................... 95
20. VOICE PROMPT TEST COMMANDS................................................................................................. 96
20.1
Record .................................................................................................................................... 97
20.2
Play......................................................................................................................................... 98
20.3
Save_NV................................................................................................................................. 99
20.4
Read_NV .............................................................................................................................. 100
21. FXS STATUS DISPLAY COMMAND ................................................................................................ 101
21.1
Show..................................................................................................................................... 102
22.
FXO STATUS DISPLAY COMMANDS............................................................................................. 103
22.1
Show..................................................................................................................................... 104
23.
DIGITAL TRUNK STATUS DISPLAY COMMANDS......................................................................... 105
23.1
Atx......................................................................................................................................... 106
23.2
Loopback .............................................................................................................................. 107
24.
R2 STATUS DISPLAY COMMANDS ............................................................................................... 108
24.1
Show..................................................................................................................................... 109
24.2
Block ..................................................................................................................................... 110
24.3
Unblock................................................................................................................................. 111
25. TRACE INFORMATION COMMANDS.............................................................................................. 112
25.1
Show..................................................................................................................................... 113
25.2
R2 ......................................................................................................................................... 114
25.3
Lapd...................................................................................................................................... 115
26. AUTOMATIC SYSTEM DIAGNOSIS COMMAND............................................................................. 116
26.1
Automatic .............................................................................................................................. 117
