Document Preview & Text Transcription
Instructions and warnings for the fitter
Istruzioni ed avvertenze per l’installatore
Instructions et recommandations pour l’installateur
Anweisungen und Hinweise für den Installateur
Instrucciones y advertencias para el instalador
Instrukcje i uwagi dla instalatora
Aanwijzingen en aanbevelingen voor de installateur
For projecting
and non-projecting
up-and-over doors,
and sectional doors
Spin
Spin
2
Table of contents:
page
1
Warnings
3
2
Product description
3
2.1
Operating limits
4
2.2
Typical system
5
2.3
List of cables
5
3
Installation
6
3.1
Preliminary checks
6
3.2
Fitting SPIN
6
3.2.1
Assembly of guide supplied with
7
SPIN20KCE, SPIN30 and SPIN40
3.2.2
SNA5 guide assembly
7
3.2.3
SNA6 guide assembly
7
3.2.4
Fixing the gearmotor to the guide
8
3.2.5
Fixing the gearmotor to the ceiling
8
3.3
Installation of the Various Devices
10
3.4
Electrical connections
10
3.5
Description of the electrical connections
11
4
Final checks and start up
11
4.1
Power Supply Connection
11
4.2
Recognition of the devices
12
4.3
Recognizing the door opening and
closing positions
12
4.4
Checking door movements
12
4.5
Pre-set functions
13
4.6
Radio receiver
13
4.6.1
Memorization of the Radio Transmitters
13
4.6.2
Memorization Mode I
14
4.6.3
Memorization Mode II
14
4.6.4
“Remote” memorization
14
4.6.5
Deleting the Radio Transmitters
15
4.6.6
Declaration of conformity of the radio receiver
and transmitters
15
5
Testing and commissioning
15
5.1
Testing
15
5.2
Commissioning
16
6
Maintenance and Disposal
16
6.1
Maintenance
16
6.2
Disposal
16
7
Additional information
17
7.1
Programming buttons
17
7.2
Programming
17
7.2.1
Level one functions (ON-OFF functions).
17
7.2.2
Level one programming (ON-OFF functions).
18
7.2.3
Level two functions (adjustable parameters)
18
7.2.4
Level two programming (adjustable parameters) 18
7.2.5
Level one programming example
(ON-OFF functions).
19
7.2.6
Level two programming example
(adjustable parameters)
19
7.3
Adding or Removing Devices
19
7.3.1
BlueBUS
19
7.3.2
STOP Input
20
7.3.3
Photocells
20
7.3.4
Recognition of other devices
21
7.4
Special functions
21
7.4.1
“Always open” Function
21
7.4.2
“Move anyway” Function
21
7.5
Connection of other devices
21
7.6
Troubleshooting
22
7.7
Diagnostics and Signals
22
7.7.1
Signalling with flashing light and courtesy light
22
7.7.2
Signals on the control unit
23
7.8
Accessories
24
8
Technical characteristics
25
Instructions and Warnings for users of SPIN gearmotor
27
GB
3
SPIN is a range of gearmotors designed for the automation of sec-
tional doors and, in combination with accessory SPA5 (supplied sep-
arately), protruding or non-protruding spring or counterweight over-
head doors.
The electrical connections to external devices have been simplified
through the use of “BlueBUS”, a technique by which several devices
can be connected up using just 2 wires.
SPIN operates with electric power. In the event of a power failure, the
gearmotor can be released in order to move the door manually. Alter-
natively, for some versions, there is the PS124 buffer battery acces-
sory which makes it possible to use the door also during the event
of a power failure.
The products described in tables 1 and 2 belong to the SPIN range.
SN6031 must be completed with the guides SNA5 (3m) or SNA6 (3m + 1m).
SN6041 must be completed with the guide SNA6 (3m + 1m).
SPIN30; SPIN40; SN6031 and SN6041 can be completed with radio receivers SMXI or SMXIS and relative radio transmitters
* 120V for the SPIN/V1 versions
1) Warnings
This manual contains important information regarding safety; before you
start installing the components, it is important that you read all the infor-
mation contained herein. Store this manual safely for future use.
In this manual when all data, warnings and other information related to
all products are stated, the range name “SPIN” will be used. The
description of individual products can be found in chapter “2 Product
description”.
Considering the hazards that may exist during the installation and oper-
ation of SPIN, installation must be carried out in strict compliance with
current legislation, standards and regulations. This chapter provides
details of general warnings. Other, more specific warnings are detailed in
Chapters “3.1 Preliminary Checks” and “5 Testing and commissioning”.
According to the most recent European legislation, the
production of automatic doors or gates is governed by the
provisions listed in Directive 98/37/CE (Machine Directive)
and, more specifically, to provisions: EN 12445; EN 12453 and
EN 12635, which enable manufacturers to declare the pre-
sumed conformity of the product.
Please access “www.niceforyou.com” for further information, and guide-
lines for risk analysis and how to draw up the Technical Documentation.
• This manual has been especially written for use by qualified fitters.
Except for the enclosed specification “Instructions and Warnings for
Users of the SPIN gearmotor” which is to be removed by the installer,
none of the information provided in this manual can be considered as
being of interest to end users!
• Any use or operation of SPIN which is not explicitly provided for in
these instructions is not permitted. Improper use may cause damage
and personal injury.
• Risk analysis must be carried out before starting installation, to include
the list of essential safety requisites provided for in Enclosure I of the
Machine Directive, indicating the relative solutions employed. N.B. Risk
analysis is one of the documents included in the “Technical Documen-
tation” for this automation.
• Check whether additional devices are needed to complete the
automation with SPIN based on the specific application requirements
and dangers present. The following risks must be considered: impact,
crushing, shearing, dragging, etc. as well as other general dangers.
• Do not make modifications to any components unless such action is
specified in this manual. Operations of this type are likely to lead to
malfunctions. NICE disclaims any liability for damage resulting from
modified products.
• During installation and use, ensure that solid objects or liquids do not
penetrate inside the control unit or other open devices. If necessary,
please contact the NICE customer service department; the use of
SPIN in these conditions can be dangerous.
• The automation system must not be used until it has been commis-
sioned as described in chapter 5: “ Testing and commissioning”.
• The packing materials of SPIN must be disposed of in compliance with
local regulations.
• If a fault occurs that cannot be solved using the information provided
in this manual, refer to the NICE customer service department.
• In the event that any automatic switches are tripped or fuses blown,
you must identify the fault and eliminate it before resetting the switch-
es or replacing fuses.
• Disconnect all the power supply circuits before accessing the terminals
inside the SPIN cover. If the disconnection device is not identifiable,
post the following sign on it: “WARNING: MAINTENANCE WORK IN
PROGRESS”.
!
GB
2) Product description
1
Model:
Gearmotor
Guide
Radio receiver
Radio Transmitter
SPIN20KCE
SN6021
3x1m
SMXI
FLO2R-S
SPIN21KCE
SN6021
3m
SMXI
FLO2R-S
SPIN30
SN6031
3x1m
---
---
SPIN40
SN6041
3x1m
---
---
SN6031
SN6031
---
---
---
SN6041
SN6041
---
---
---
Table No. 1: Description of the SPIN components
Gearmotor type
SN6021
SN6031
SN6041
Maximum torque
(corresponding to the maximum force)
11.7 Nm (650N)
11.7 Nm (650N)
18 Nm (1000N)
Reduced consumptoin in Stand-By
No
Yes
Yes
Max. no. BlueBus units
2
6
6
Emergency power supply
No
with PS124
with PS124
Courtesy light (lamp fitting)
12V - 21W (BA15)
230V* - 60W (E27)
230V* - 60W (E27)
Table No. 2: comparison of main features of SPIN gearmotors
4
2.1) Operating limits
Chapter 8 “Technical Characteristics” provides the data needed to determine whether the products of the SPIN line are suitable for the intend-
ed application.
The structural characteristics of the SPIN products make it suitable for use on sectional and overhead doors within the limits shown in Tables
3, 4 and 5.
The measurements in table N° 3 are guideline only and can be used as a general estimate only. The effective suitability of SPIN for automat-
ing a specific door depends on the degree of door leaf balancing, guide friction and other aspects, including occasional phenomena such as
wind pressure or the presence of ice, which could obstruct leaf movement.
To establish effective conditions, the force required to move the leaf throughout its stroke must be measured, to ensure that this value does
not exceed the “rated torque” specified in chapter “8 Technical specifications”; also, to calculate the number of cycles/hour and consecutive
cycles, the data in tables 4 and 5 must be taken into account.
The height of the door enables a calculation of the maximum number of cycles per hour and consecutive cycles, while the force required to
move the door enables a calculation of the percentage of cycle reduction; for example, if the leaf height is 2.2 m this would enable 15 cycles
per hour and 7 consecutive cycles, but if a force of 300N is required, using a SN6021 gearmotor, these would have to be reduced to 70%,
resulting therefore in 10 cycles per hour and around 5 consecutive cycles. To avoid overheating, the control unit has a limiter that is based
on the motor operation and duration of cycles, and trips when the maximum limit is exceeded.
N.B. 1Kg = 9.81N, meaning that 500N, for example, is equivalent to 51Kg.
Model:
SECTIONAL door
OVERHEAD door, non-protruding
OVERHEAD door, protruding (with accessory
(with accessory SPA5)
SPA5) or with springs (without SPA5)
Height
Width
Height
Width
Height
Width
SPIN20KCE
2.4m
4.4m
2.2m
4.2m
2.8m
4.2m
SPIN21KCE
2.4m
4.4m
2.2m
4.2m
2.8m
4.2m
SPIN30
2.4m
4.4m
2.2m
4.2m
2.8m
4.2m
SPIN40
2.4m
5.2m
2.2m
4.2m
2.8m
4.2m
SN6031 (SNA5)
2.4m
4.4m
2.2m
4.2m
2.8m
4.2m
SN6031 (SNA6)
3.4m
3.1m
3.2m
2.9m
3.5m
3.4m
SN6041 (SNA6)
3.4m
5.2m
3.2m
4.2m
3.5m
4.2m
Table No. 3: SPIN gearmotor operating limits
Leaf height
Max. no. of cycles/hour
Max. no. of consecutive cycles
Max. 2
20
10
2÷2,5
15
7
2,5÷3
12
5
3÷3,5
10
4
Table 4: limits related to leaf height
Force required to move leaf N
Cycle reduction percentage
SN6021 - SN6031
SN6041
Max. 250
100%
100%
250÷400
70%
90%
400÷500
25%
70%
500÷650
---
40%
650÷850
---
25%
Table N°5: limits in relation to force required to move door leaf
