Numark MP102 Manuals

CD / MP3 Player Quick Start Owner’s Manual Manual de inicio rápido del usuario(ESPAÑOL) Schnellbedienungsanleitung(DEUTSCH) Manuale Rapido di Utilizzazione(ITALIANO) Guide d’utilisation simplifié (FRANÇAIS) CONTENU DE LA BOÎTE • UNITÉ DE TRANSPORT DU LECTEUR CD • CÂBLES DE CONNEXION RCA • CÂBLE D’ALIMENTATION CONTENUTO DELLA CONFEZIONE: • UNITÀ DI TRASPORTO LETTORE CD • CAVO DI ALIMENTAZIONE • CAVI DI CONNESSIONE RCA INHALT DER SCHACHTEL • TRANSPORT EINHEIT F. CD-SPIELER • STROMKABEL • RCA-VERBINDUNGSKABEL CONTENIDO DE LA CAJA • REPRODUCTOR DE CD • CABLE DE ALIMENTACIÓN • CABLES CONECTORES BOX CONTENTS • CD/MP3 PLAYER • POWER CORD • RCA CONNECTING CABLES 2 MP102 QUICK SETUP 1. Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. 4. Place MP102 in an appropriate position for operation. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into power. 9. Switch everything on in the following order: • audio input sources (i.e. turntables or CD players) • MP102 • last, any amplifiers or output devices 10. When turning off, always reverse this operation by, • turning off amplifiers • MP102 • last, any input devices 11. Go to http://www.numark.com for product registration. More information about this product may be found at http://www.numark.com REAR CONNECTIONS 1. XLR Balanced Audio Connectors – Low impedance XLR output connectors. 2. Power Plug Connector - Plug your supplied power cord in here. 3. Voltage Selector - Set this switch to the voltage for your location. 4. RCA Audio Connectors - Connect your CD player to your mixer from this line level output. 5. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In order to use the digital output you should not use variable pitch slider and the pitch bend buttons. If you adjust the pitch, other devices may not read the digital output properly because the sampling rate changes 3 CD PLAYER FEATURES 1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject the disc. Each press will open or close the disc tray on the transport. NOTE: Tray will not open unless the disc has been paused. Tray will automatically close after 30 seconds. 2. TIME (Time Button) - Switches the time display between elapsed playing time and remaining time on the track and remaining time on the entire CD. 3. CONT/SING - Will cause just a single track to play or all tracks in order by pressing once or twice. 4. LCD DISPLAY - Indicates all the functions, as they are occurring, with the CD. These functions are explained in the next section. 5. TRACK (Track Buttons) - Used to select the track to be played. 6. Folder/+10 Button – Steps up or down through folders on MP3 discs. On a disc which contains no folders, this button advances the track by 10. 7. PROGRAM - Depress this button and the unit will stop and the program indicator will light. Select each track to be programmed and press the PROGRAM button between selections. You can program up to 20 tracks. Press PLAY to start the program. To exit and erase program, either hold the program button down for more than 2 seconds while the unit is stopped, open the disc tray, or turn off the power. 8. PITCH (Pitch Button) - Activates the Pitch Slider. To alternate between ±8% and ±16%, press and hold the PITCH button. The LED will indicate the pitch setting. 9. PITCH SLIDER - The pitch can be changed up to ±16% by pressing the PITCH button so the PITCH LED is lit, then moving the sliding fader. The pitch will not be changed if the PITCH LED is off. 10. SEARCH WHEEL (OUTER RING) - 3 forward and 3 reverse speed positions for searching through songs. The more you turn the wheel in either direction the faster you search through the music. 11. PITCH BEND/JOG WHEEL (INNER RING) - The jog wheel serves 2 functions depending on the current mode. a) The jog wheel will control a slow frame search when the CD is not playing. To set a new frame cue point, spin the wheel then press play when you have determined the proper position. Press CUE to return to the “CUE POINT”. b) When both CD players are playing a CD, the pitch bend function allows the positioning of the bass beats to be matched after the pitch of each disc is matched. Either player can “catch up” or “fall back” to match the other player. The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to speed up or counterclockwise to slow down. By changing the pitch of one disc with respect to the pitch of the other disc, the beats can be matched. c) After you press the Previous or Next Track buttons, you can use the wheel to quickly scroll through tracks. This is especially useful on MP3 CD’s with a large number of tracks. 12. CUE - Pressing the CUE button during play provides a return to the position at which play was started. If PAUSE is used before CUE, that will become the cue point. Alternately pressing the PLAY button and the CUE button allows the CD to be played from the same position any number of times. The CUE LED will light up from the time the CUE button is pressed until the CD has been reset to the position at which play was started. Steady lighting of this LED indicates the ready condition. 13. START/PAUSE (Play/Pause Button) - Each press of the Play/Pause Button causes the operation to change from play to pause or from pause to play. 14. LOOP IN – Used for setting a start loop point and new cue points during playback. 15. LOOP OUT – Used for setting the end loop point and releasing the loop action. 16. RELOOP / STUTTER – Depending on mode, as explained further, this button is used for either repeating a previously set loop or seamlessly stuttering on the last set cue point.

CD / MP3 Player Quick Start Owner’s Manual Manual de inicio rápido del usuario(ESPAÑOL) Schnellbedienungsanleitung(DEUTSCH) Manuale Rapido di Utilizzazione(ITALIANO) Guide d’utilisation simplifié (FRANÇAIS) CONTENU DE LA BOÎTE  UNITÉ DE TRANSPORT DU LECTEUR CD  CÂBLES DE CONNEXION RCA  CÂBLE D’ALIMENTATION CONTENUTO DELLA CONFEZIONE:  UNITÀ DI TRASPORTO LETTORE CD  CAVO DI ALIMENTAZIONE  CAVI DI CONNESSIONE RCA INHALT DER SCHACHTEL  TRANSPORT EINHEIT F. CD-SPIELER  STROMKABEL  RCA-VERBINDUNGSKABEL CONTENIDO DE LA CAJA  REPRODUCTOR DE CD  CABLE DE ALIMENTACIÓN  CABLES CONECTORES BOX CONTENTS  CD/MP3 PLAYER  POWER CORD  RCA CONNECTING CABLES 2 MP102 QUICK SETUP 1. Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. 4. Place MP102 in an appropriate position for operation. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into power. 9. Switch everything on in the following order:  audio input sources (i.e. turntables or CD players)  MP102  last, any amplifiers or output devices 10. When turning off, always reverse this operation by,  turning off amplifiers  MP102  last, any input devices 11. Go to http://www.numark.com for product registration. More information about this product may be found at http://www.numark.com REAR CONNECTIONS 1. XLR Balanced Audio Connectors – Low impedance XLR output connectors. 2. Power Plug Connector - Plug your supplied power cord in here. 3. Voltage Selector - Set this switch to the voltage for your location. 4. RCA Audio Connectors - Connect your CD player to your mixer from this line level output. 5. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In order to use the digital output you should not use variable pitch slider and the pitch bend buttons. If you adjust the pitch, other devices may not read the digital output properly because the sampling rate changes 3 CD PLAYER FEATURES 1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject the disc. Each press will open or close the disc tray on the transport. NOTE: Tray will not open unless the disc has been paused. Tray will automatically close after 30 seconds. 2. TIME (Time Button) - Switches the time display between elapsed playing time and remaining time on the track and remaining time on the entire CD. 3. CONT/SING - Will cause just a single track to play or all tracks in order by pressing once or twice. 4. LCD DISPLAY - Indicates all the functions, as they are occurring, with the CD. These functions are explained in the next section. 5. TRACK (Track Buttons) - Used to select the track to be played. 6. Folder/+10 Button – Steps up or down through folders on MP3 discs. On a disc which contains no folders, this button advances the track by 10. 7. PROGRAM - Depress this button and the unit will stop and the program indicator will light. Select each track to be programmed and press the PROGRAM button between selections. You can program up to 20 tracks. Press PLAY to start the program. To exit and erase program, either hold the program button down for more than 2 seconds while the unit is stopped, open the disc tray, or turn off the power. 8. PITCH (Pitch Button) - Activates the Pitch Slider. To alternate between ±8% and ±16%, press and hold the PITCH button. The LED will indicate the pitch setting. 9. PITCH SLIDER - The pitch can be changed up to ±16% by pressing the PITCH button so the PITCH LED is lit, then moving the sliding fader. The pitch will not be changed if the PITCH LED is off. 10. SEARCH WHEEL (OUTER RING) - 3 forward and 3 reverse speed positions for searching through songs. The more you turn the wheel in either direction the faster you search through the music. 11. PITCH BEND/JOG WHEEL (INNER RING) - The jog wheel serves 2 functions depending on the current mode. a) The jog wheel will control a slow frame search when the CD is not playing. To set a new frame cue point, spin the wheel then press play when you have determined the proper position. Press CUE to return to the “CUE POINT”. b) When both CD players are playing a CD, the pitch bend function allows the positioning of the bass beats to be matched after the pitch of each disc is matched. Either player can “catch up” or “fall back” to match the other player. The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to speed up or counterclockwise to slow down. By changing the pitch of one disc with respect to the pitch of the other disc, the beats can be matched. c) After you press the Previous or Next Track buttons, you can use the wheel to quickly scroll through tracks. This is especially useful on MP3 CD’s with a large number of tracks. 12. CUE - Pressing the CUE button during play provides a return to the position at which play was started. If PAUSE is used before CUE, that will become the cue point. Alternately pressing the PLAY button and the CUE button allows the CD to be played from the same position any number of times. The CUE LED will light up from the time the CUE button is pressed until the CD has been reset to the position at which play was started. Steady lighting of this LED indicates the ready condition. 13. START/PAUSE (Play/Pause Button) - Each press of the Play/Pause Button causes the operation to change from play to pause or from pause to play. 14. LOOP IN – Used for setting a start loop point and new cue points during playback. 15. LOOP OUT – Used for setting the end loop point and releasing the loop action. 16. RELOOP / STUTTER – Depending on mode, as explained further, this button is used for either repeating a previously set loop or seamlessly stuttering on the last set cue point. 4 LCD DISPLAY FEATURES 1. PAUSE: This shows when the unit is paused. 2. PLAY: The shows when a CD is playing. 3. CUE: Flashing when the unit is setting a cue point. Lit continuously when the unit is paused at a cue point. 4. PROGRAM: Used for pre-programming the track order to automatically be played by the unit. This is a great function if you need to leave the CD player alone. 5. TIME MODE: (Elapsed) is for showing time as it is taking place.(Remain) shows how much time is left on a particular track. This function is controlled by the TIME BUTTON. 6. TIME BAR: Shows either time remaining or elapsed depending on the setting of the TIME BUTTON. 7. TRACK NUMBER: Shows the current track number. While searching folders, this shows “F”. 8. TRACK: Shows when unit is in Track List mode instead of Folder mode. 9. SINGLE: Shows when the unit is set to play just one track at a time. When this is not lit, the CD will play continuously through all tracks. This function is controlled by the SING/CONT BUTTON. 10. MP3: Shows when unit is playing an MP3 file. 11. MINUTES: Shows the minutes elapsed or remaining depending on mode setting. 12. SECONDS: Shows the seconds elapsed or remaining depending on mode setting. 13. FRAMES: The CD Player breaks down a second into 75 frames for accurate cueing. This shows the frames elapsed or remaining depending on mode setting. 14. LOOP: Indicates when loop is actively playing. 15. PITCH: Shows the percentage change in pitch. 16. PITCH: Is lit when the PITCH BUTTON is active. 17. MATRIX DISPLAY: Displays CD Text or MP3 Tag information. If reading a disc with no encoding, display will read “NO TEXT”. Also displays folder names while searching through folders.

CD / MP3 Player Quick Start Owner’s Manual Manual de inicio rápido del usuario(ESPAÑOL) Schnellbedienungsanleitung(DEUTSCH) Manuale Rapido di Utilizzazione(ITALIANO) Guide d’utilisation simplifié (FRANÇAIS) CONTENU DE LA BOÎTE � UNITÉ DE TRANSPORT DU LECTEUR CD � CÂBLES DE CONNEXION RCA � CÂBLE D’ALIMENTATION CONTENUTO DELLA CONFEZIONE: � UNITÀ DI TRASPORTO LETTORE CD � CAVO DI ALIMENTAZIONE � CAVI DI CONNESSIONE RCA INHALT DER SCHACHTEL � TRANSPORT EINHEIT F. CD-SPIELER � STROMKABEL � RCA-VERBINDUNGSKABEL CONTENIDO DE LA CAJA � REPRODUCTOR DE CD � CABLE DE ALIMENTACIÓN � CABLES CONECTORES BOX CONTENTS � CD/MP3 PLAYER � POWER CORD � RCA CONNECTING CABLES 2 MP102 QUICK SETUP 1. Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. 4. Place MP102 in an appropriate position for operation. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into power. 9. Switch everything on in the following order: � audio input sources (i.e. turntables or CD players) � MP102 � last, any amplifiers or output devices 10. When turning off, always reverse this operation by, � turning off amplifiers � MP102 � last, any input devices 11. Go to http://www.numark.com for product registration. More information about this product may be found at http://www.numark.com REAR CONNECTIONS 1. XLR Balanced Audio Connectors – Low impedance XLR output connectors. 2. Power Plug Connector - Plug your supplied power cord in here. 3. Voltage Selector - Set this switch to the voltage for your location. 4. RCA Audio Connectors - Connect your CD player to your mixer from this line level output. 5. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In order to use the digital output you should not use variable pitch slider and the pitch bend buttons. If you adjust the pitch, other devices may not read the digital output properly because the sampling rate changes 3 CD PLAYER FEATURES 1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject the disc. Each press will open or close the disc tray on the transport. NOTE: Tray will not open unless the disc has been paused. Tray will automatically close after 30 seconds. 2. TIME (Time Button) - Switches the time display between elapsed playing time and remaining time on the track and remaining time on the entire CD. 3. CONT/SING - Will cause just a single track to play or all tracks in order by pressing once or twice. 4. LCD DISPLAY - Indicates all the functions, as they are occurring, with the CD. These functions are explained in the next section. 5. TRACK (Track Buttons) - Used to select the track to be played. 6. Folder/+10 Button – Steps up or down through folders on MP3 discs. On a disc which contains no folders, this button advances the track by 10. 7. PROGRAM - Depress this button and the unit will stop and the program indicator will light. Select each track to be programmed and press the PROGRAM button between selections. You can program up to 20 tracks. Press PLAY to start the program. To exit and erase program, either hold the program button down for more than 2 seconds while the unit is stopped, open the disc tray, or turn off the power. 8. PITCH (Pitch Button) - Activates the Pitch Slider. To alternate between ±8% and ±16%, press and hold the PITCH button. The LED will indicate the pitch setting. 9. PITCH SLIDER - The pitch can be changed up to ±16% by pressing the PITCH button so the PITCH LED is lit, then moving the sliding fader. The pitch will not be changed if the PITCH LED is off. 10. SEARCH WHEEL (OUTER RING) - 3 forward and 3 reverse speed positions for searching through songs. The more you turn the wheel in either direction the faster you search through the music. 11. PITCH BEND/JOG WHEEL (INNER RING) - The jog wheel serves 2 functions depending on the current mode. a) The jog wheel will control a slow frame search when the CD is not playing. To set a new frame cue point, spin the wheel then press play when you have determined the proper position. Press CUE to return to the “CUE POINT”. b) When both CD players are playing a CD, the pitch bend function allows the positioning of the bass beats to be matched after the pitch of each disc is matched. Either player can “catch up” or “fall back” to match the other player. The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to speed up or counterclockwise to slow down. By changing the pitch of one disc with respect to the pitch of the other disc, the beats can be matched. c) After you press the Previous or Next Track buttons, you can use the wheel to quickly scroll through tracks. This is especially useful on MP3 CD’s with a large number of tracks. 12. CUE - Pressing the CUE button during play provides a return to the position at which play was started. If PAUSE is used before CUE, that will become the cue point. Alternately pressing the PLAY button and the CUE button allows the CD to be played from the same position any number of times. The CUE LED will light up from the time the CUE button is pressed until the CD has been reset to the position at which play was started. Steady lighting of this LED indicates the ready condition. 13. START/PAUSE (Play/Pause Button) - Each press of the Play/Pause Button causes the operation to change from play to pause or from pause to play. 14. LOOP IN – Used for setting a start loop point and new cue points during playback. 15. LOOP OUT – Used for setting the end loop point and releasing the loop action. 16. RELOOP / STUTTER – Depending on mode, as explained further, this button is used for either repeating a previously set loop or seamlessly stuttering on the last set cue point. 4 LCD DISPLAY FEATURES 1. PAUSE: This shows when the unit is paused. 2. PLAY: The shows when a CD is playing. 3. CUE: Flashing when the unit is setting a cue point. Lit continuously when the unit is paused at a cue point. 4. PROGRAM: Used for pre-programming the track order to automatically be played by the unit. This is a great function if you need to leave the CD player alone. 5. TIME MODE: (Elapsed) is for showing time as it is taking place.(Remain) shows how much time is left on a particular track. This function is controlled by the TIME BUTTON. 6. TIME BAR: Shows either time remaining or elapsed depending on the setting of the TIME BUTTON. 7. TRACK NUMBER: Shows the current track number. While searching folders, this shows “F”. 8. TRACK: Shows when unit is in Track List mode instead of Folder mode. 9. SINGLE: Shows when the unit is set to play just one track at a time. When this is not lit, the CD will play continuously through all tracks. This function is controlled by the SING/CONT BUTTON. 10. MP3: Shows when unit is playing an MP3 file. 11. MINUTES: Shows the minutes elapsed or remaining depending on mode setting. 12. SECONDS: Shows the seconds elapsed or remaining depending on mode setting. 13. FRAMES: The CD Player breaks down a second into 75 frames for accurate cueing. This shows the frames elapsed or remaining depending on mode setting. 14. LOOP: Indicates when loop is actively playing. 15. PITCH: Shows the percentage change in pitch. 16. PITCH: Is lit when the PITCH BUTTON is active. 17. MATRIX DISPLAY: Displays CD Text or MP3 Tag information. If reading a disc with no encoding, display will read “NO TEXT”. Also displays folder names while searching through folders.