Optex OVS-01GT Manuals

-1- ● Vehicle detection is ensured by a combination of microwave and ultrasonic wave. ● A microwave sensor can detect the presence of a vehicle based on FMCW (Frequency-modulated continuous-wave). ● Detection of objects other than a vehicle can be reduced (patent pending). ● Built-in heater reduces snow on the sensor (automatically activates based on the outside air temperature). ● Not affected by underground obstructions, this product is installed above ground. ● Reduced installation time as access road for vehicle is not closed, as no civil engineering works is required.. Installation Instructions OVS-01GT Vehicle Detection Sensor for Gate Features No.59-2643-0 171013 Safety Precautions Component Name Before Using the Product Detection Principle and Basic Operation of the Sensor Sensor Installation Recommendations Sensor Detection Conditions Installation Workflow Installation Steps (Basic) Installation of the Units Setting Verification and Adjustment Calibration Detection Area Check Other Functions Advanced Installation Sensitivity Human Cancel Adjustment Presence Detection Timer Sensitivity Boost Timer Ultrasonic Maximum Range Input Troubleshooting Specifications Specifications Detection Area Diagram Dimensions 2 3 4 4 5 6 7 9 9 12 13 14 16 17 17 18 19 21 22 23 24 26 26 27 27 1 2 3 4 5 6 7 Table of Contents 3-1 3-2 3-3 3-4 4-1 4-2 4-3 4-4 4-5 5-1 5-2 5-3 5-4 5-5 5-6 7-1 7-2 7-3

OVS-01GT Quick Reference Guide 1. If used for Activation, go to section 2. If used for Vehicle protection, go to section 3. 2. If Activation mode, find the installation location by referring the following chart. Installation height has to be 500mm(19.69” ) from the ground. 3. If Vehicle protection mode, find the installation location by referring the following chart. Always recommended to install 700mm(70.87” ) far from barrier or slide gate. Installation height has to be 500mm(19.69” ) from the ground. [1] Make holes to mount the sensor. [2] Run a cable thru the post or pole. [4] Mount the base using 4 screws. [5] Connect wires. Power Supply 12-24VDC Non-Voltage Relay Output N.O. / N.C. Switchable 30VDC 0.3A or less (resistance load) Applicable Wire Single conductor: 0.5-1.2mm (equivalent to CPEV) Stranded wire: 0.3-2.0sq Signal GNP Input Active High / Low Switchable Power Output Input 5. Set the Microwave maximum range and Sensor mode as follows: Activation : 5m(16.4’ ) Vehicle protection : 3.5m(11.48’ ) (factory default setting) Usually, other settings can be default settings. For detailed settings, refer to Advance Installation on page 17. Sensor Mode Calibration Output 4 4.5 5 5.5 2 2.5 3 3.5 N.O. N.C. Activation Vehicle Protection Microwave Maximum Range (m) Sensor Mode button Microwave Maximum Range botton 6. Perform sensor calibration in order to memorize the background of the detection area. Ensure no pedestrians or vehicles are present. Calibration Area Check Standby Area Check Detection Calibration Calibration Error 1. Press the Calibration button. 2. Operation indicator blinks in blue. 7. System operation check. Check the entire coverage area by using actual vehicle. Left side of the lane Center of the lane Right side of the lane [6] Attach the sensor body to the base and adjust the sensor angle. 8. Put the front cover on the top of the base first, and attach it while spreading it open and pushing down the front cover. 9. Tighten the front cover retaining screw. [3] Loosen the retaining screws on the bottom of the front cover and remove the front cover, detach the sensor unit. Hold here and pull forward Vehicle Path 1800mm (70.87in.) Gate Bar Operation Type: Activation Installation Height of 500mm(19.69in.) Island 45° Ticket Vending Machine 150mm (5.90in.) 4. Install the sensor, wire it and apply power. GL+588(23.15) Mounting Pitch 32±1 (1.26±0.04) Mounting Pitch 70±1(2.76±0.04) 5(0.20) M4 Tap Depending on the cable diameter [Unit : mm(inch)] Gate Operation Type: Vehicle Protection Installation Height of 500mm(19.69in.) 30° 100mm(3.94in.) 1100mm (43.3in.) Secure side Public side Vehicle Path Gate 90° 100mm(3.94in.) 90° Operation Type: Vehicle Protection Installation Height of 500mm(19.69in.) Secure side Public side 700mm (27.56in.) 700mm (27.56in.) Vehicle Path 90° Gate Bar 150mm (5.90in.) Island 700mm(27.56in.) Operation Type:Vehicle Protection Installation Height of 500mm(19.69in.) Ticket Vending Machine Vehicle Path 500mm(19.69in.) 500mm(19.69in.) Barrier Gate Slide Gate Barrier Gate Slide Gate 3. Step away from sensor and outside detection area. 4. Green LED lights when done correctly.

OVS-01GT Product set up guide Version. 12MAR2020