Osaki MT32E Manuals

E C LOW VOLTAGE DIRECTIVE 73/23/EEC E C ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 89/336/EEC E C MACHINERY DIRECTIVE 89/392/EEC DECLARATION OF CONFORMITY We hereby certify that OSAKI MT32E Multi Power Tool Complies with all the relevant provisions of the EC Directives 73/23/EEC, 89/336/EEC & 89/392/EEC Harmonised Standards Applied: EN55104-1, EN55014, EN60555-2, EN60555-3, EN50144-2-5, EN292T1, EN292T2A1, EN294, EN349, EN28662T1. Official Agent KENNEDY TOOLS Wigston Works, Leicester, England. ISO 9002 REGISTERED COMPANY Signed: Date: 1st February 2002 Name: Martin Cooke Position: Director, The Kennedy Group Ltd. © The Kennedy Group Ltd. 02/02 QUALITY GUARANTEE & WARRANTY OSAKI POWER TOOLS carry one years manufacturers warranty. OSAKI POWER TOOLS are designed & produced to the highest standards & specifications OSAKI POWER TOOLS are fully guaranteed against faulty materials & workmanship Should they be found to be defective, they will either be repaired or replaced free of charge (fair wear and tear and/or misuse excepted). Please retain supplier invoice as proof of purchase. AVAILABLE FROM YOUR DISTRIBUTOR OPERATORS MANUAL MULTI POWER TOOL MT32E ORDER CODE OSA-279-8500K 02 Press OSA-279-8500K Manual.qxd 21/03/02 14:47 Page 1 2 SAFETY INSTRUCTIONS Osaki Power Tools are committed to the Production of Quality Power Tools that are designed for high performance and long service life. If safety and maintenance procedures are observed they will last for many years. Man, Earth and the Universe are forces that create an immovable centre of balance . . . the balance of power “ ” 7 PARTS BREAKDOWN No. Description Order Code OSA-298 1 QUICK CHANGE COLLET NUT KIT -1101S 2 COLLET NUT -1102S 3 FINGER REST -1103S 4 BEARING 698-2Z -1104S 5 SCREW NAIL -1105S 6 FIELD COIL (STATOR) -1106S 7 ARMATURE -1107S 8 CARBON BRUSH SET -1108S 9 BEARING 626-2Z -1109S 10 CIRCUIT BOARD SET -1110S 11 ON-OFF SWITCH SET -1111S 12 SCREW NAIL -1112S 13 WIRE GRIP BLOCK -1113S 14 ELECTRIC WIRE -1114S 15 WIRE COVER -1115S 16 SHAFT LOCK BUTTON -1116S 17 SPRING -1117S 18 SHAFT LOCK PIN -1118S 19 SHELL SET -1119S 20 RING -1120S 21 VARIABLE SPEED CONTROL -1121S 22 COLLET SPANNER 280-1607T GENERAL SAFETY � Keep work area clean - clutter invites injury. � Store tool in a dry, secure place, away from children. � Always keep the cord away from moving parts of the tool. � Always wear safety glasses and a dust mask if necessary. � Before using the tool ensure that all parts are functional. A damaged part should be repaired and serviced by an authorised technician. � Ensure work area is well lit. � Disconnect the tool from the power source when not in use. � Stay alert at all times. Watch what you are doing and use your common sense. Do not operate tools when you are tired. � In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug. � Only use original Osaki accessories which can be obtained from your Osaki dealer. � Ensure that the collet size corresponds with the shaft size of the accessory. � Compare the maximum allowed rpm of each accessory with that of the tool. � Do not expose power tools to rain or damp conditions. � Do not store the machine in locations where the temperature may reach or exceed 50oC (122oF). � Do not use power tools near flammable liquids or gases. � Do not let people who are not familiar with power tools handle them without supervision. � Use the correct tool for the job, do not force small tools or attachments to do the job of a heavy tool. The job will be done more efficiently and safely if the tool is used at the intended rate. � Never apply force. � Do not try to stop the accessory rotating with your hand. Wait for it to stop. � Never press the shaft lock while the tool is running. � Do not use grinding wheels over 11/4” (32mm) diameter. � Do not use drill bits over 1/8” (3.2mm) diameter. SPECIFICATIONS Model Number MT32E Nominal Voltage 230v~50 Hz Power Consumption 120W No Load Speed Speed 8,000-30,000rpm Noise 82db(A) Weight 640gms Complies to EN 50144-1 & EN 68 1977. Press OSA-279-8500K Manual.qxd 21/03/02 14:47 Page 2 6 OPERATING INSTRUCTIONS PARTS BREAKDOWN 3 MT32E MULTI POWER TOOL ORDER CODE OSA-279-8500K USE• Keep the air vent openings clean and uncovered. • Mounting accessories: - Push and hold shaft lock. - Turn collet nut until shaft locks into position. - Loosen collet nut by hand or using spanner. - Insert accessory. - Tighten collet nut. - Release shaft lock. • Holding the tool - Hand grip for rough work such as grinding. - Pencil grip for precision work such as engraving. APPLICATION ADVICE • Practice on a piece of scrap material first to choose the right accessory and to determine the correct speed. • Let the speed of the tool do the work for you and do not apply too much pressure. • Recommended speeds are: Low - Medium for polishing & cleaning Medium - High for other applications Variable Speed Control On/Off Holder Shaft Lock Finger Rest Collet Nut Carbon Brush Holder Carbon Brush Holder the balance of power ” ” Hand Grip Pencil Grip 14 20 3 18 2 7 17 16 15 21 1 4 5 11 10 12 13 8 9 6 19 22 Press OSA-279-8500K Manual.qxd 21/03/02 14:47 Page 3