Panasonic WV-SFV481 Manuals

Operating Instructions Network Camera Model No. WV-SFV481 WV-SFN480 WV-SFN480PJ WV-SFV481 WV-SFN480 This manual covers the models: WV-SFV481, WV-SFN480 and WV-SFN480PJ. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. Important Information Network Camera Model No. WV-SFV481/WV-SFN480 WV-SFV481 WV-SFN480 PGQX1661ZA Cs1114-0 Printed in China

Installation Guide Network Camera Model No. WV-SFV481 PGQX1665YA Cs1114-1045 Printed in China ● This manual describes the installation procedures, network camera installation, cable connections, and the direction of the image adjustment. ● Before reading this manual, be sure to read the Important Information. Major operating controls The component names of the camera are as follows. Refer to the illustration when installing or adjusting the camera. Standard accessories Making connections Important Information ............................... 1 pc. Installation Guide (this document) ............ 1 set Warranty card ........................................... 1 set CD-ROM*1 ................................................. 1 pc. Code label*2 .............................................. 1 pc. *1 The CD-ROM contains the operating instructions and different kinds of tool software pro- grams. *2 This label may be required for network management. The network administrator shall retain the code label. The following parts are used during installation procedures. A Attachment plate .................................. 1 pc. B Base bracket ........................................ 1 pc. C Fixing screws for attachment plate (M4 x 8 mm) ...................................... 5 pcs. (incl. 1 spare) D Template A (for the attachment plate) .... 1 sheet E Template B (for the base bracket) ..... 1 sheet F Waterproof tape ................................... 1 pc. G Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T10) .................... 1 pc. H 4P alarm cable ..................................... 1 pc. I 2P power cable .................................... 1 pc. J LAN cable cover................................... 1 pc. F ● How to initialize the camera Follow the steps below to initialize the network camera. 1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam- era. When using an external power supply, disconnect the 2P power cable plug from the camera. 2 Turn on the power of the camera while holding down the INITIAL SET button, and then keep holding down the button for 5 seconds or more. About 2 minutes later, the camera will start up and the settings including the network settings will be initialized. Turn off each system’s power supply before making a connection. Before making connections, prepare the required peripheral devices and cables. IMPORTANT: ● When the camera is initialized, the settings including the network settings will be initialized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized. ● Before initializing the settings, it is recommended to write down the settings in advance. ● Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and may cause malfunction. IMPORTANT: ● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight, STP). ● The maximum cable length is 100 m {328 feet}. ● Make sure that the PoE device in use is compliant with IEEE802.3af standard. ● When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V DC will be used for power supply*. * If a 12 V DC power supply and a PoE hub or router are used at the same time, network connections may not be possible. In this case, disable the PoE settings. Refer to the operating instructions of the PoE hub or router in use. * Depending on the PoE device used, if you stop the 12 V DC power supply after operating it and a PoE hub or router at the same time, the power supply may stop, causing the camera to restart. ● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds. When the cable is quickly reconnected, the power may not be supplied from the PoE device. ● When cables are used outdoors, there is a chance that they may be affected by lightning. In this case, install a lightning arrester just before where the cables con- nect to the camera. Connect a LAN cable Waterproof treatment for the cable joint sections When connecting to a network using a PoE hub Microphone/line input cable Connect a stereo mini plug (ø3.5 mm). ● Input impedance: Approx. 2 kΩ (unbalanced) ● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input) Less than 10 m {32.8 feet} (for line input) ● Recommended microphone: Plug-in power type (option) •Supply voltage: 2.5 V ±0.5 V •Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz) ● Input level for the line input: Approx. -10 dBV IMPORTANT: ● Be sure to use the H 4P alarm cable (accessory) provided with this product. ● Install external devices so that they do not exceed the ratings above. ● When using the external I/O terminals as the output terminals, ensure they do not cause signal collision with external signals. Connect the alarm input/output cable • ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3 Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up) OFF: Open or 4 V - 5 V DC ON: Make contact with GND (required drive current: 1 mA or more) • ALARM OUT, AUX OUT Output specification: Open collector output (maximum applied voltage: 20 V DC) Open: 4 V - 5 V DC by internal pull-up Close: Output voltage 1 V DC or less (maximum drive current: 50 mA) * The default of EXT I/O terminals is “Off”. Connect an external amplifier-embedded speaker to the audio/monitor output cable Connect a stereo mini plug (ø3.5 mm).* ● Output impedance: Approx. 600 Ω (unbalanced) ● Recommended cable length: Less than 10 m {32.8 feet} ● Output level: -20 dBV (can switch to monitor output) IMPORTANT: ● Connect/disconnect the audio cables and turn on the power of the camera after turn- ing off the power of the audio output devices. Otherwise, loud noise may be heard from the speaker. ● Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is connected, audio may not be heard. When connecting a monaural speaker with amplifier, use a locally procured conver- sion cable (mono-stereo). Adequate waterproof treatment is required for the cables when installing the camera with cables exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the supplied waterproof tape at the points where the cables are connected to ap- ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunction. Before starting the installation, check the entire system configuration. The following illustration gives a wiring example of how to connect the camera to the network via a PoE device (hub). < Alarm input/output cable, power cable, microphone/ line input cable, audio/monitor output cable> Wind the tape in a half-overlapping manner. Wind the tape in a half-overlapping manner. Wind the tape in a half-overlapping manner. Wind the tape in a half-overlapping manner. IMPORTANT: How to wind the supplied waterproof tape ● Also waterproof the I 2P power cable (accessory), H 4P alarm cable (accessory), and external connec- tions in the same way. ● Stretch the tape to approx. twice its length (see the illustration) and wind it around the cable. Insufficient tape stretch causes insufficient waterproofing. ● To prevent the LAN cable hook from coming loose easily, fit the J LAN cable cover (accessory) onto the pigtail cable as illustrated, and then slide it in the direction indicated by the arrow. The connector of the LAN cable used with this cam- era must meet the following restrictions. Height when inserted (From bottom to hook.): Max. 16 mm {5/8 inches} Connector width: Max. 14 mm {9/16 inches} ● To install this product outdoors, be sure to waterproof the cables. Waterproof grade (IEC IP66 or equiva- lent) is applied to this product only when it is installed correctly as described in these operating instructions and appropriate waterproof treatment is applied. The internal parts of B base bracket (accessory) are not waterproofed. 2x Stretch the tape to approx. twice its length. PoE device (hub) PC LAN cable (category 5 or better, straight) Analog monitor LAN cable (category 5 or better, straight) LAN cable (category 5 or better, straight) Powered speaker Microphone * IMPORTANT: ● The analog monitor is used when servicing the camera. It is not provided for record- ing/monitoring use. ● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be displayed on the screen. ● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX. ● If a PoE hub is not used, each network camera must be connected to a 12 V DC power supply. ● When using 12 V DC, power supply from a PoE hub or router is not required. INITIAL SET button 1 When the SD ON/OFF button is pressed, data can be saved to the SD memory card. 2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes out, and the SD memory card can be removed. SD ON/OFF button The hook engages with the connector terminal J LAN cable cover (accessory) ● When data is being sent via the network camera Blinks green (accessing) ACT indicator ● When the camera is able to communicate with the Lights orange connected device LINK indicator ● When an SD memory card is inserted and could Lights off → Blinks green → be recognized Lights off ● When data can be saved after the SD memory card is Lights off → Lights green inserted and the SD ON/OFF button is pressed ● When data can be saved to the SD memory card Lights green ● When the SD memory card is removed after holding down Lights green → Blinks green → Lights off (recording) the SD ON/OFF button for about 2 seconds Lights green → Lights off (waiting for recording) ● When data cannot be saved to the SD memory card because Lights off an abnormality was detected or the SD memory card is configured not to be used SD MOUNT indicator ● When ABF (Auto Back Focus) operation is being executed Blinks red (Interval of 1 time/ second) ● When the set is being started Lights red ● When an SD memory card*3 is recognized normally Lights red → Lights off ● When the SD memory card slot is not used or an abnormality Lights red → Stays red is detected in SD memory card after the camera has started SD ERROR/ABF indicator *1 The detailed specifications on the right side of this page describe each terminal and cable. *2 Data Matrix is our website address converted into a two-dimensional barcode. Depending on the scanning application used, the Data Matrix may not be able to be read correctly. In this case, access the site by directly entering the following URL. http://security.panasonic.com/pss/security/support/qr_sp_select.html *3 SDXC/SDHC/SD memory card is described as SD memory card. H 4P alarm cable (accessory) GND (black) ALARM IN3, AUX OUT (gray) (Alarm input 3, AUX output) ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output) ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ Color-monochrome switching input) Connect the output cable of the AC adaptor to the I 2P power cable (accessory). Power cable 12 V DC Red Positive Black Negative LAN cable (category 5 or better, straight) Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC. For U.S. and Canada: Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America www.panasonic.com/business/ For customer support, call 1.800.528.6747 Two Riverfront Plaza, Newark, NJ 07102-5490 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 www.panasonic.ca For Europe and other countries: Panasonic Corporation http://panasonic.net Panasonic System Networks Co., Ltd. Fukuoka, Japan Authorised Representative in EU: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg, Germany * Use an external powered speaker. Connect the power cable IMPORTANT: ● Use 12 V DC power supply that is insulated from the commercial AC power. ● Be sure to use the I 2P power cable (accessory) provided with this product. ● Be sure to fully insert the I 2P power cable (accessory) into the 12 V DC power supply terminal. Otherwise, it may damage the camera or cause malfunction. ● When installing the camera, make sure that excessive force is not applied to the power cable. ● Be sure to use an AC adaptor compliant with the specifications (written in the indication label on the bottom side of this unit) regarding power source and power consumption. Caution: ● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY. ● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/ UL/CSA 60950-1). Included Installation Instructions © Panasonic System Networks Co., Ltd. 2014 I 2P power cable (accessory) RJ45 (female) Network cable Alarm input/output cable Microphone/line input cable (white) Audio/monitor output cable (black) * Can switch to monitor output LAN cable (category 5 or better, straight) H 4P alarm cable (accessory) Power cable (12 V DC) 12 V DC (red) GND (black) G (Hex wrench, screw size 6.35 mm {1/4 inches} T10) Dome cover Sub cover C Fixing screws for attachment plate (accessory) Enclosure Camera A Attachment plate (accessory) B Base bracket (accessory) Direction marker for installation “ TOP” Image rotation gear Power/audio/ alarm cable*1 Dehumidifying device Camera fixing screw Network cable*1 Data Matrix: To our website*2 SD memory card slot cover ACT indicator LINK indicator SD ERROR/ABF indicator INITIAL SET button SD memory card slot SD ON/OFF button SD MOUNT indicator Note: ● The ACT indicator, Link indicator, SD ERROR/ABF indicator, and SD MOUNT indicator inside the SD memory card slot cover can be turned off. (Indicators are set to light or blink in the default settings.) Turn off the indicators as required according to the installation environment. (☞ Operating Instructions (included in the CD-ROM)) * Can switch to monitor out (select the [Setup]→ [Basic] tab, and then select [Monitor out]) Note: ● Off, input, and output of the external I/O terminal 2 and 3 can be switched by config- uring the setting. Refer to the Operating Instructions on the provided CD-ROM for further information about the external I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”, “Alarm input”, “Alarm output” or “AUX output”). Note: ● Audio out is selected for the audio/monitor output cable by default. The cable can be used for monitor out by selecting the [Setup] → [Basic] tab, and then selecting [Monitor out]. (The ø3.5 mm monaural mini plug RCA pin jack conversion cable is locally procured.)

Operating Instructions Network Camera Model No. WV-SFV481 WV-SFN480 WV-SFV481 WV-SFN480 This manual covers the models: WV-SFV481 and WV-SFN480. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.