Paradox IP150 Manuals

IP150-EI04 07/2019 PARADOX.COM Description The IP150 Internet Module is a multi-function Internet communication module that offers SWAN connectivity or static IP address connectivity. It is fully configurable from the integrated web interface. The IP150 provides freedom to access your system and receive push or email notifications (depending on configuration) from anywhere around the world. Before You Begin (Static Mode Only) Make sure you have a web-enabled computer. You will also require the following in order to configure your IP150 Internet Module: • Ethernet-compatible computer with internet access (required for remote access) • Router • 4-pin serial cable (included) • CAT5 Ethernet cable (maximum 90m (295 ft.), not included) • Insite Gold app • Paradox IP Exploring Tools Software (required for remote access) Figure 1 - IP Communication Overview Connecting and Installing the IP150 Figure 2 - IP150 Overview Metal Box Installation Figure 3 - Metal Box Installation To connect and install the IP150: 1) Connect the 4-pin serial cable between the panel’s serial connector and the IP150’s panel connector. 2) Connect the Ethernet cable between the router and the IP150’s network connector. 3) The on-board LEDs will illuminate to indicate the IP150’s status. 4) Clip the IP150 to the top of the metal box (refer to Metal Box Installation). LED Indicators Reset IP150 to Default To reset the IP150 module to its default settings, insert a pin/straightened paper clip (or similar) into the pin hole located between the two I/O LEDs. Press down gently until you feel some resistance; hold it down for approximately 5 seconds, release it when the I/O and RX/TX LEDs start flashing, and then press it again. The I/O and RX/TX LEDs will remain lit during the reset. IP Reporting When using IP reporting, the IP150 has the ability to poll the monitoring station. To enable IP reporting, the IP150 must first be registered to the monitoring station’s IP Receiver (IPR512) or to the IPRS-7 software. Telephone reporting can be used in conjunction with, or as a backup to IP reporting. Before registering the IP150, the following information must be obtained from the monitoring station: • Account number(s) - One account number for each partition used. IP/GPRS reporting uses a different set of account numbers than those used for dialer reporting. • IP address(es) - (12-digit number e.g., for 195.4.8.250 you must enter 195.004.008.250). The IP address(es) indicate(s) which of the monitoring station’s IP Receivers will be used for IP reporting. • IP port(s) (5-digit number; for 4-digit numbers, enter 0 before the first digit). The IP port refers to the port used by the monitoring station’s IP Receiver. • Receiver password(s) (up to 32-digits). The receiver password is used to encrypt the IP150 registration process. • Security profile(s) (2-digit number). The security profile indicates how frequently the monitoring station is polled by the IP150. Security profile numbers and polling frequency are defined by the monitoring station. Setting Up IP Reporting 1) Ensure the panel’s report code format is set to Ademco Contact ID: MG/SP: section [810] EVO: section [3070] 2) Enter the IP reporting account numbers (one for each partition): MG/SP: section [918] / [919] EVO: section [2976] to [2983] Please make sure that reporting codes are programmed in the panel, refer to the corresponding Programming Guide for more details. In the General IP Options section, set up IP line monitoring options and dialer options, and ensure IP reporting is enabled (refer to the following tables). MG/SP: section [806] EVO: section [2975] 4) Enter the monitoring station’s IP address(es), IP port(s), receiver password(s), and security profile(s) (information must be obtained from the monitoring station). 5) Register the IP150 module with the monitoring station. To register, enter the sections below and press [ARM]. The registration status is displayed as well as any registration errors. NOTES: An IP150 used with an MG/SP system will always poll using the partition 1 IP account number. When using an EVO system, the partition 1 IP account is used by default, but can be defined in section [3020]. All reported system events will originate from the partition selected in this section. Remote Access (Static Mode Only) In order to configure your system for remote access you will need IP Exploring Tools, a web browser and access to your router. The following steps will guide you in setting up remote access. Step 1: Setting up the Router This step allows you to set up the router so that the IP150 module can function properly. 1) Ensure the router is connected properly as indicated in the router’s instructions. 2) Access your router’s configuration page. Refer to your router’s manual for the exact procedure. In most cases, this is done by entering the router’s static IP address in the address bar of your Web browser. For this instance, we will use 192.168.1.1 as an example for the router’s IP address that may be indicated in the router’s instructions or on a sticker on the router. Enter the monitoring station’s IP 3) In the router’s configuration page, check the DHCP settings (screen shot below may differ depending on type of router used). IP150 Internet Module Installation Manual Version 4.40 and higher Left Side View Right Side View Front View LED Description User On when a user is connected via Insite Gold/BabyWare/InField. Internet LED Status SWAN On Connected Flashing Trying to connect Off No connection Link Solid Yellow = Valid Link @ 10Mbps Solid Green = Valid Link @ 100Mbps LED will flash according to data traffic Flashing Yellow/Green = DHCP trouble RX/TX On after first successful communication exchange Flashes when data is transmitted or received through/from panel Off when no connection has been established I/O 1 On when activated I/O 2 On when activated IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Trouble only On Off When disarmed: Trouble only When armed: Audible alarm On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled Enabled IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Audible alarm On Off When disarmed: Trouble only (default) When armed: Trouble only On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled MG/SP Sections IP Receiver #1 #2 Backup IP Address1 [929] [936] [943] IP Port1 [930] [937] [944] IP Address2 [931] [938] [945] IP Port2 [932] [939] [946] IP Password [933] [940] [947] IP Profile [934] [941] [948] EVO Sections IP Receiver #1 #2 #3 #4 IP Address1 [2984] [2986] [2988] [2990] IP Port1 IP Address2 IP Port2 IP Password IP Profile MG/SP Registration IP Receiver # #1 #2 Backup Register/Status [935] [942] [949] EVO Registration IP Receiver # #1 #2 #3 #4 Register/Status [2985] [2987] [2989] [2991]

IP150 Internet Module Installation Manual V1.0 - IP150-EI00 Printed in Canada 02/2013 Description The IP150 Internet Module is an HTTPs-supported IP communication device that enables you to control and monitor your security system through any web browser (e.g., Google Chrome). The IP150 provides freedom to access your system and receive instant, SSL encrypted email notifications anywhere in the world when your system detects activity. So no matter where you are, you will have access to arm, disarm, and more. Before You Begin Before you begin, make sure that you have web-enabled computer. You will also require the following system requirements in order to configure to your IP150 Internet Module. System requirements include: • Ethernet-compatible computer with internet access (required for remote access) • Router • 4-pin serial cable (included) • CAT-5 Ethernet cable (maximum 90m (295 ft.), not included) • Paradox IP Exploring Tools Software (required for remote access). Software can be downloaded from our website (www.paradox.com/GSM/IP/Voice/IP). Figure 1: IP Communication Overview Connecting and Installing the IP150 Figure 2: IP150 Overview @Email Notification Home PC Router Router Web Access IPR512 IP Receiver Monitoring Station Control Panel IP150 WAN Front View Right Side View Left Side View Metal Box Installation To connect and install the IP150: 1) Connect the 4-pin serial cable between the panel’s serial connector and the IP150’s panel connector (see Right Side View in Figure 2). 2) Connect the Ethernet cable between the router and the IP150’s network connector (see Left Side View in Figure 2). 3) The onboard LEDs will illuminate to indicate the IP150’s status (see Front View in Figure 2). 4) Clip the IP150 to the top of the metal box (see Metal Box Installation in Figure 2). LED Indicators Reset IP150 to Default To reset the IP150 module to its default settings, insert a pin/straightened paper clip (or similar) into the pin hole located between the two I/O LEDs. Press down gently until you feel some resistance; hold it down for approximately 5 seconds, release it when the I/O and RX/TX LEDs start flashing, and then press it again. The I/O and RX/TX LEDs will remain lit during the reset. IP Reporting When using IP reporting, the IP150 has the ability to poll the monitoring station. To enable IP reporting, the IP150 must first be registered to the monitoring station’s IP Receiver (IPR512). Telephone reporting can be used in conjunction with, or as a backup to IP reporting. Before registering the IP150, the follow- ing information must be obtained from the monitoring station: • Account number(s) - One account number for each partition used. IP/GPRS reporting uses a different set of account numbers than those used for dialer reporting. • IP address(es) - (12-digit number e.g., for 195.4.8.250 you must enter 195.004.008.250) • The IP address(es) indicate(s) which of the monitoring station’s IP Receivers will be used for IP reporting. • IP port(s) (5-digit number; for 4-digit numbers, enter 0 before the first digit). The IP port refers to the port used by the monitoring station’s IP Receiver. • Receiver password(s) (up to 32-digits) • The receiver password is used to encrypt the IP150 registration process. • Security profile(s) (2-digit number). The security profile indicates how frequently the monitoring station is polled by the IP150. Security profile numbers and polling frequency are defined by the monitoring station. Setting Up IP Reporting 1) Ensure that the panel’s report code format is set to Ademco Contact ID: MG/SP/E: section [810] EVO: section [3070] 2) Enter the IP reporting account numbers (one for each partition): MG/SP/E: section [918] / [919] EVO: section [2976] to [2983] 3) In the General IP Options section, set up IP line monitoring options and dialer options, and ensure IP reporting is enabled (see the following tables). LED Description User On when a user is connected Internet LED Status Internet Connection ParadoxMyHome Enabled On Connected Connected Flashing Connected No connection Off No connection No connection LED Status Internet Connection ParadoxMyHome Disabled On Connection No connection Off No connection No connection Link Solid Yellow = Valid Link @ 10Mbp; Solid Green = Valid Link @ 100Mbp; LED will flash according to data traffic. Flashing Yellow/Green = DHCP trouble. Rx/Tx On after first successful communication exchange; Flashes when data is transmitted or received through/from panel; Off when no connection has been established. I/O 1 On when activated I/O 2 On when activated MG/SP/E: section [806] EVO: section [2975] 4) Enter the monitoring station’s IP address(es), IP port(s), receiver password(s), and security profile(s) (information must be obtained from the monitoring station). 5) Register the IP150 module with the monitoring station. To register, enter the sections below and press [ARM]. The registration status is displayed as well as any registration errors. NOTE: An IP150 used with an MG/SP/E system will always poll using the partition 1 IP account num- ber. When using an EVO system, the partition 1 IP account is used by default, but can be defined in section [3020]. All reported system events will originate from the partition selected in this section. Remote Access The IP150 provides remote access to control and monitor a security system via web browsers or PC software. This provides the user with the freedom to access the system from anywhere in the world. The following steps will guide you in setting up remote access. Step 1: Setting up the Router This step allows you to set up the router so that the IP150 module can function properly. 1) Ensure that the router is connected properly as indicated in the router’s instructions. 2) Access your router’s configuration page. Refer to your router’s manual for the exact procedure. In most cases, this is done by entering the router’s static IP address in the address bar of your Web browser. For this instance, we will use 192.168.1.1 as an example.Your router’s IP address may be indicated in the router’s instructions or on a sticker on the router. IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Trouble only On Off When disarmed: Trouble only When armed: Audible alarm On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/ GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled IP Line Monitoring Options [5] [6] Off Off Disabled Off on When disarmed: Trouble only When armed: Audible alarm On Off When disarmed: Trouble only (default) When armed: Trouble only On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/ GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled MG/SP/E Sections IP Receiver #1 #2 Backup IP Address1 [929] [936] [943] IP Port1 [930] [937] [944] IP Address2 [931] [938] [945] IP Port2 [932] [939] [946] IP Password [933] [940] [947] IP Profile [934] [941] [948] EVO Sections IP Receiver #1 #2 #3 #4 IP Address1 [2984] [2986] [2988] [2990] IP Port1 IP Address2 IP Port2 IP Password IP Profile MG/SP/E Registration IP Receiver # #1 #2 Backup Register/Status [935] [942] [949] EVO Registration IP Receiver # #1 #2 #3 #4 Register/Status [2985] [2987] [2989] [2991]

IP150+-EI00 02/2020 PARADOX.COM Description The IP150+ Internet Module provides access to Paradox systems. With the IP150+, connecting to a system is possible with the Insite GOLD application, PC software for programming, upgrade and monitoring, as well as reporting to the central station by connecting to Paradox receivers. Before You Begin (Static Mode Only) Make sure you have the following in order to configure your IP150+ Internet Module: • Router • 4-pin serial cable (included) • CAT5 Ethernet cable (maximum 90m (295 ft.), not included) • Insite Gold app • Paradox IP Exploring Tools Software (required for remote access) • Connect IP150+ to the serial port on your panel and Ethernet port of your router Figure 1 - IP Communication Overview Connecting and Installing the IP150+ Figure 2 - IP150+ Overview Installation Figure 3 - Metal and Plastic Box Installation To connect and install the IP150+: 1) Connect the 4-pin serial cable between the panel’s serial connector and the IP150+’s panel connector. 2) Connect the Ethernet cable between the router and the IP150+’s network connector. 3) The on-board LEDs will illuminate to indicate the IP150+’s status. 4) Clip the IP150+ to the top of the metal box or plastic box, as shown in Figure 3. LED Indicators Reset IP150+ to Default Settings To reset the IP150+ module to its default settings, ensure that the module is turned on and then insert a pin/straightened paper clip (or similar) into the pinhole located between the two I/O LEDs. Press down gently until you feel some resistance; hold it down for approximately five seconds. When the I/O and RX/ TX LEDs start flashing, release it and then press it again (figure 2). The I/O and RX/TX LEDs will remain lit during the reset. Reset IP150+ to Default Firmware Version To reset the IP150+ module to its default firmware version, unplug the power cable from the panel and insert a pin/straightened paper clip (or similar object) into the pinhole located between the two I/O LEDs. Press down gently until you feel some resistance; plug in the power cable while holding the pin down for approximately five seconds and release it when the I/O 2 LED starts flashing (figure 2). The I/O LED will turn solid and start blinking (resetting to the backup version). Once complete, the IP150+ will reboot automatically to the default firmware version. IP Reporting When using IP reporting, the IP150+ has the ability to poll the monitoring station. To enable IP reporting, the IP150+ must first be registered to the monitoring station’s IP Receiver (IPR512) or to the IPRS-7 software. Telephone reporting can be used in conjunction with, or as a backup to IP reporting. Before registering the IP150+, the following information must be obtained from the monitoring station: • Account number(s) - One account number for each partition used. IP/GPRS reporting uses a different set of account numbers than those used for dialer reporting. • IP address(es) - (12-digit number e.g., for 195.4.8.250 you must enter 195.004.008.250). The IP address(es) indicate(s) which of the monitoring station’s IP Receivers will be used for IP reporting. • IP port(s) (5-digit number; for 4-digit numbers, enter 0 before the first digit). The IP port refers to the port used by the monitoring station’s IP Receiver. • Receiver password(s) (up to 32-digits). The receiver password is used to encrypt the IP150+ registration process. • Security profile(s) (2-digit number). The security profile indicates how frequently the monitoring station is polled by the IP150+. Security profile numbers and polling frequency are defined by the monitoring station. Setting Up IP Reporting 1) Ensure the panel’s report code format is set to Ademco Contact ID: MG/SP: section [810] EVO: section [3070] 2) Enter the IP reporting account numbers (one for each partition): MG/SP: section [918] / [919] EVO: section [2976] to [2983] Please make sure that reporting codes are programmed in the panel, refer to the corresponding Programming Guide for more details. In the General IP Options section, set up IP line monitoring options and dialer options, and ensure IP reporting is enabled (refer to the following tables). MG/SP: section [806] EVO: section [2975] 4) Enter the monitoring station’s IP address(es), IP port(s), receiver password(s), and security profile(s) (information must be obtained from the monitoring station). 5) Register the IP150+ module with the monitoring station. To register, enter the sections below and press [ARM]. The registration status is displayed as well as any registration errors. NOTES: An IP150+ used with an MG/SP system will always poll using the partition 1 IP account number. When using an EVO system, the partition 1 IP account is used by default, but can be defined in section [3020]. All reported system events will originate from the partition selected in this section. Remote Access (Static Mode Only) In order to configure your system for remote access you will need IP Exploring Tools, a web browser and access to your router. The following steps will guide you in setting up remote access. Step 1: Setting up the Router This step allows you to set up the router so that the IP150+ module can function properly. 1) Ensure the router is connected properly as indicated in the router’s instructions. 2) Access your router’s configuration page. Refer to your router’s manual for the exact procedure. In most cases, this is done by entering the router’s static IP address in the address bar of your Web browser. For this instance, we will use 192.168.1.1 as an example for the router’s IP address that may be indicated in the router’s instructions or on a sticker on the router. Enter the monitoring station’s IP. IP150+ Internet Module Installation Manual Left Side View Right Side View Front View Reset switch (use pin) LED Description User Green - On when a user is connected via Insite Gold/BabyWare/InField. Internet Solid green Internet present and SWAN connected Flashing - Internet present Trying to connect to the SWAN server Off No internet connection Link Solid Yellow = connected @ 10Mbps Solid Green = connected @ 100Mbps LED will flash according to data traffic Flashing Yellow/Green = No IP address / DHCP fail (check router) RX/TX On when connected to panel Flashes when data is transmitted or received through/from panel Off when no connection to panel I/O 1 On when activated I/O 2 On when activated IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Trouble only On Off When disarmed: Trouble only When armed: Audible alarm On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Audible alarm On Off When disarmed: Trouble only (default) When armed: Trouble only On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled MG/SP Sections IP Receiver #1 #2 Backup IP Address1 [929] [936] [943] IP Port1 [930] [937] [944] IP Address2 [931] [938] [945] IP Port2 [932] [939] [946] IP Password [933] [940] [947] IP Profile [934] [941] [948] EVO Sections IP Receiver #1 #2 #3 #4 IP Address1 [2984] [2986] [2988] [2990] IP Port1 IP Address2 IP Port2 IP Password IP Profile MG/SP Registration IP Receiver # #1 #2 Backup Register/Status [935] [942] [949] EVO Registration IP Receiver # #1 #2 #3 #4 Register/Status [2985] [2987] [2989] [2991] Metal Box Plastic Box

IP150+-EI01 04/2021 PARADOX.COM Description The IP150+ Internet Module provides access to Paradox systems. With the IP150+, connecting to a system is possible with the Insite GOLD application, PC software for programming, upgrade and monitoring, as well as reporting to the central station by connecting to Paradox receivers. Figure 1 - IP Communication Overview Before You Begin (Static Mode Only) Make sure you have the following in order to configure your IP150+ Internet Module: • Router • 4-pin serial cable (included) • CAT5 Ethernet cable (maximum 90m (295 ft.), not included) • Insite Gold app • Connect IP150+ to the serial port on your panel and Ethernet port of your router Connecting and Installing the IP150+ Figure 2 - IP150+ Overview Installation Figure 3 - Metal and Plastic Box Installation To connect and install the IP150+: 1) Connect the 4-pin serial cable between the panel’s serial connector and the IP150+’s panel connector. 2) Connect the Ethernet cable between the router and the IP150+’s network connector. 3) The on-board LEDs will illuminate to indicate the IP150+’s status. 4) Clip the IP150+ to the top of the metal box or plastic box, as shown in Figure 3. LED Indicators Reset IP150+ to Default Settings To reset the IP150+ module to its default settings, ensure that the module is turned on and then insert a pin/straightened paper clip (or similar) into the pinhole located between the two I/O LEDs. Press down gently until you feel some resistance; hold it down for approximately five seconds. When the I/O and RX/ TX LEDs start flashing, release it and then press it again (figure 2). The I/O and RX/TX LEDs will remain lit during the reset. Firmware Version Fallback To revert the IP150+ module to its previously installed firmware version, unplug the power cable from the panel and insert a pin/straightened paper clip (or similar object) into the pinhole located between the two I/O LEDs. Press down gently until you feel some resistance; plug in the power cable while holding the pin down for approximately five seconds and release it when the I/O 2 LED starts flashing (figure 2). The I/O LED will turn solid and start blinking (resetting to the backup version). Once complete, the IP150+ will reboot automatically to the default firmware version. IP Reporting When using IP reporting, the IP150+ has the ability to poll the monitoring station. To enable IP reporting, the IP150+ must first be registered to the monitoring station’s IP Receiver (IPR512) or to the IPRS-7 software. Telephone reporting can be used in conjunction with, or as a backup to IP reporting. Before registering the IP150+, the following information must be obtained from the monitoring station: • Account number(s) - One account number for each partition used. IP/GPRS reporting uses a different set of account numbers than those used for dialer reporting. • IP address(es) - (12-digit number e.g., for 195.4.8.250 you must enter 195.004.008.250). The IP address(es) indicate(s) which of the monitoring station’s IP Receivers will be used for IP reporting. • IP port(s) (5-digit number; for 4-digit numbers, enter 0 before the first digit). The IP port refers to the port used by the monitoring station’s IP Receiver. • Receiver password(s) (up to 32-digits). The receiver password is used to encrypt the IP150+ registration process. • Security profile(s) (2-digit number). The security profile indicates how frequently the monitoring station is polled by the IP150+. Security profile numbers and polling frequency are defined by the monitoring station. Setting Up IP Reporting 1) Ensure the panel’s report code format is set to Ademco Contact ID: MG/SP: section [810] EVO: section [3070] 2) Enter the IP reporting account numbers (one for each partition): MG/SP: section [918] / [919] EVO: section [2976] to [2983] Please make sure that reporting codes are programmed in the panel, refer to the corresponding Programming Guide for more details. In the General IP Options section, set up IP line monitoring options and dialer options, and ensure IP reporting is enabled (refer to the following tables). MG/SP: section [806] EVO: section [2975] 4) Enter the monitoring station’s IP address(es), IP port(s), receiver password(s), and security profile(s) (information must be obtained from the monitoring station). NOTE: For Contact ID reporting, all report codes should be set to FF in order tor receive all events. 5) Register the IP150+ module with the monitoring station. To register, enter the sections below and press [ARM]. The registration status is displayed as well as any registration errors. NOTE: An IP150+ used with an MG/SP system will always poll using the partition 1 IP account number. When using an EVO system, the partition 1 IP account is used by default, but can be defined in section [3020]. All reported system events will originate from the partition selected in this section. Remote Access (SWAN) When using the IP150+ with SWAN, the SWAN connection is seamless. Please make sure that the ISP or router/firewall is not blocking the following ports that needs to be permanently open (whitelisted) for TCP and UDP: 1) Port 10000 - Configurable SW port on IP150+ from Insite GOLD Installer Menu, used for NEware closed network, Locate IP in the network and firmware upgrading. 2) Ports 53, 443, 3478 and 5683 - used to communicate with the SWAN Server. Remote Access (Static Public IP Mode Only) In order to configure your system for remote access you will need access to your router. The following steps will guide you in setting up remote access so that the IP150+ module can function properly. 1) Ensure the router is connected properly as indicated in the router’s instructions. 2) Access your router’s configuration page. Refer to your router’s manual for the exact procedure. In most cases, this is done by entering the router’s static IP address in the address bar of your Web browser. For this instance, we will use 192.168.1.1 as an example for the router’s IP address that may be indicated in the router’s instructions or on a sticker on the router. IP150+ Internet Module Installation Manual Left Side View Right Side View Front View Reset switch (use pin) Metal Box Plastic Box LED Description User Green - On when a user is connected via Insite Gold/BabyWare/InField. Internet Solid green Internet present and SWAN connected Flashing - Internet present Trying to connect to the SWAN server Off No internet connection Link Solid Yellow = connected @ 10Mbps Solid Green = connected @ 100Mbps LED will flash according to data traffic Flashing Yellow/Green = No IP address / DHCP fail (check router) RX/TX On when connected to panel Flashes when data is transmitted or received through/from panel Off when no connection to panel I/O 1 On when activated I/O 2 On when activated IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Trouble only On Off When disarmed: Trouble only When armed: Audible alarm On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled IP Line Monitoring Options [5] [6] Off Off Disabled Off On When disarmed: Trouble only When armed: Audible alarm On Off When disarmed: Trouble only (default) When armed: Trouble only On On Silent alarm becomes audible alarm OFF ON [7] Use dialer reporting (telephone)  As backup for IP/GPRS reporting  In addition to IP reporting [8] IP/GPRS reporting  Disabled  Enabled MG/SP Sections IP Receiver #1 #2 Backup IP Address1 [929] [936] [943] IP Port1 [930] [937] [944] IP Address2 [931] [938] [945] IP Port2 [932] [939] [946] IP Password [933] [940] [947] IP Profile [934] [941] [948] EVO Sections IP Receiver #1 #2 #3 #4 IP Address1 [2984] [2986] [2988] [2990] IP Port1 IP Address2 IP Port2 IP Password IP Profile MG/SP Registration IP Receiver # #1 #2 Backup Register/Status [935] [942] [949] EVO Registration IP Receiver # #1 #2 #3 #4 Register/Status [2985] [2987] [2989] [2991]

IP150+-EP00 PARADOX.COM IP150+ Internet Module Web Programming Guide Introduction The IP150+ Internet Module provides access to Paradox systems. With the IP150+, connecting to a system is possible with the Insite GOLD application, PC software for programming, upgrade and monitoring, as well as reporting to the central station by connecting to Paradox receivers. Connecting via IP150+ Internet Module In order to connect to your IP150+, you will need the following information: • IP address and port • Panel Master code To connect with your system from an external computer: 1) Open a web browser (e.g., Google Chrome). 2) In the address bar, enter IP address and Port number or open IP exploring tools and double-click on the IP device you wish to connect to. 3) Log in using your panel master code. Receiver Configuration Screen The Receiver Configuration Screen allows you to configure your module for IP Reporting. Receiver Status The IP150+ module status information is displayed in this section. Domain Name for IP Reporting Enter a DNS with a DNS or DDNS provider. Also, enter your DNS in the section WAN1, WAN2. An IP address must be programmed into the reporting section of the control panel for the Domain Name field to be accessible and functional. System Information Screen The system information screen contains important hardware and software information on both your security system, your IP150+ module, and PCS module (if present), and panel. The PCS module section is only visible if a PCS module is detected.

IP150 Internet Module User Guide V1.3 - IP150-EU01 Printed in Canada 07/2013 Introduction The IP150 Internet Module is an Internet communication module that enables you to control and monitor your security system through any web browser (e.g. Internet Explorer). The IP150 provides freedom to access your system and receive email notifications anywhere in the world. IMPORTANT: The IP150 module should only be configured by the installer or a qualified network administrator. For more information on module configuration, consult the IP150 Reference and Installation Manual. Connecting via the IP150 Internet Module In order to connect to your IP150, you will need the following information: • Paradox DNS Site ID: The DNS SiteID is set by your installer. • Panel user code: This is the same code you enter on your keypad to arm the system. • Module password: The default password is “paradox”. To change your password, see “Change Password” in the Account Information Screen section. To connect with your system from an external computer: 1. Open a web browser (e.g., Google Chrome). 2. In the address bar, enter http://www.paradoxmyhome.com/SiteID where “SiteID” is your Paradox SiteID (set by your installer). 3. Log in using your panel user code and module password (default = paradox). Troubleshooting System Status Screen The System Status screen displays important system information. From the System Status screen, you can arm / disarm your system as well as monitor your system in real-time. Once you have established a connection for the first time, you are prompted to change your password from the default “paradox”. System Troubles When a trouble occurs in the system, it is displayed at the top of the System Status screen. Note: If there are no troubles in the system, the System Troubles box is not displayed. Area Status The IP150 provides a real-time display of your area status. Zone Status The IP150 provides a real-time display of your zone status. Legend The Legend gives you information on the icons shown in the Area Status display. StayD The StayD logo appears when StayD mode is enabled (Spectra SP and Magellan only). Site Name The site name uniquely identifies your system. Note: By default, your site name is “Your Paradox System”. To change your site name, see “Account Information Screen” on page 2. Account Information For information on changing account information, see page 2. Arm / Disarm Click the or button and select the arm/disarm action you with to perform. 1 1 2 2 3 3 4 4 6 6 7 7 8 8 5 5 Symptoms Solution(s) No LEDs lit; no signs of operation • Check cable connections • Check power status IP150 cannot be accessed remotely • Check spelling of access commands • Check IP and power status on unit No reporting • Verify panel troubles, panel programming, and / or receiver status If the above information does not help remedy the problem, please contact your installer.

IP150 Internet Module User Guide V1.0 - IP150-EU00 Printed in Canada 02/2013 Introduction The IP150 Internet Module is an Internet communication module that enables you to control and monitor your security system through any web browser (e.g. Internet Explorer). The IP150 provides freedom to access your system and receive email notifications anywhere in the world. IMPORTANT: The IP150 module should only be configured by the installer or a qualified network administrator. For more information on module configuration, consult the IP150 Reference and Installation Manual. Connecting via the IP150 Internet Module In order to connect to your IP150, you will need the following information: • Paradox DNS Site ID: The DNS SiteID is set by your installer. • Panel user code: This is the same code you enter on your keypad to arm the system. • Module password: The default password is “paradox”. To change your password, see “Change Password” in the Account Information Screen section. To connect with your system from an external computer: 1. Open a web browser (e.g., Google Chrome). 2. In the address bar, enter http://www.paradoxmyhome.com/SiteID where “SiteID” is your Paradox SiteID (set by your installer). 3. Log in using your panel user code and module password (default = paradox). Troubleshooting System Status Screen The System Status screen displays important system information. From the System Status screen, you can arm / disarm your system as well as monitor your system in real-time. Once you have established a connection for the first time, you are prompted to change your password from the default “paradox”. System Troubles When a trouble occurs in the system, it is displayed at the top of the System Status screen. Note: If there are no troubles in the system, the System Troubles box is not displayed. Area Status The IP150 provides a real-time display of your area status. Zone Status The IP150 provides a real-time display of your zone status. Legend The Legend gives you information on the icons shown in the Area Status display. StayD The StayD logo appears when StayD mode is enabled (Spectra SP and Magellan only). Site Name The site name uniquely identifies your system. Note: By default, your site name is “Your Paradox System”. To change your site name, see “Account Information Screen” on page 2. Account Information For information on changing account information, see page 2. Arm / Disarm Click the or button and select the arm/disarm action you with to perform. 1 1 2 2 3 3 4 4 6 6 7 7 8 8 5 5 Symptoms Solution(s) No LEDs lit; no signs of operation • Check cable connections • Check power status IP150 cannot be accessed remotely • Check spelling of access commands • Check IP and power status on unit No reporting • Verify panel troubles, panel programming, and/ or receiver status If the above information does not help remedy the problem, please contact your installer.