Parker PowerStation RS9 Manuals

CTC Parker Automation A3-06139-100 RS9 Hard Drive Installation Introduction These instructions explain how to install or replace a hard drive in the PowerStation RS9 or the RSPC9 Industrial PC. They include steps for disassembling the unit, removing a previously installed hard drive, installing a new hard drive, and reassembling the unit. Warning For safety reasons, the unit should be opened only by qualified service personnel. Warning Be sure to observe electrostatic discharge (ESD) precautions while working inside the unit. To complete this procedure, you will need the following items: • The hard drive replacement kit that you purchased: • 3.2GB Hard Drive Replacement/Upgrade Kit HDV-9003 • 6.4GB Hard Drive Replacement/Upgrade Kit HDV-9006 • Phillips-head screwdriver Disassembling the Unit To disassemble the unit, follow these steps: 1. Turn off the system. 2. Disconnect the unit from the power source. 3. Disconnect all cables attached to the unit. 4. Remove the unit from its mounted location by lifting the unit up and off its mounting screws. 5. Place the unit on a static dissipative mat, in a location free from dirt and moisture and protected against static discharge. 6. Remove the two screws at the left side of the front cover, as shown in Figure 1 on page 2. Note These screws unscrew from the back side of the unit. 7. Swing the front cover open on its hinges (left to right).

CTC Parker Automation A3-06137-100 RS9 DRAM Installation Introduction These instructions explain how to install or replace DRAM modules in the PowerStation RS9 or the RSPC9 Industrial PC. They include steps for disassembling the unit, removing previously installed DRAM module(s), installing new DRAM, and reassembling the unit. Warning For safety reasons, the unit should be opened only by qualified service personnel. Warning Be sure to observe electrostatic discharge (ESD) precautions while working inside the unit. To complete this procedure, you will need the following items: • The DRAM module(s) that you purchased: • 32MB SDRAM DIMM (DIM-9032) • 64MB SDRAM DIMM (DIM-9064 • 128MB SDRAM DIMM (DIM-9128) • 256MB SDRAM DIMM(DIM-9256) • Phillips-head screwdriver Disassembling the Unit To disassemble the unit, follow these steps: 1. Turn off the system. 2. Disconnect the unit from the power source. 3. Remove the four screws securing the back cover to the unit, as shown in Figure 1 on page 2. Note Screws 1 and 2 are located at the sides of the cover; screws 3 and 4 are in the back of the cover.

CTC Parker Automation A3-06136-100 RS9 CPU Card Replacement Introduction These instructions explain how to replace the CPU card in the PowerSta- tion RS9 or the RSPC9 Industrial PC. They include steps for disassembling the unit, removing the old CPU card, installing a new card, and reassem- bling the unit. Warning For safety reasons, the unit should be opened only by qualified service personnel. Warning Be sure to observe electrostatic discharge (ESD) precautions while working inside the unit. To complete this procedure, you will need the following items: • CPU Board Replacement Kit CPU-9000 • Phillips-head screwdriver Disassembling the Unit To disassemble the unit, follow these steps: 1. Turn off the system. 2. Disconnect the unit from the power source. 3. Disconnect all cables attached to the unit. 4. Remove the unit from its mounted location by lifting the unit up and off its mounting screws. 5. Place the unit on a static dissipative mat, in a location free from dirt and moisture and protected against static discharge. 6. Remove the four retaining screws holding the back cover onto the unit. 7. Slide the back cover off the unit, exposing the configuration bay and the CPU card, as shown in Figure 1 on page 2.

CTC Parker Automation A3-06135-100 RS9 Chassis Fan Replacement Introduction These instructions explain how to replace the fans that cool the mainte- nance compartment and the configuration bay in the PowerStation RS9 or the RSPC9 Industrial PC. They include steps for disassembling the unit, removing an old fan, installing a new fan, and reassembling the unit. Warning For safety reasons, the unit should be opened only by qualified service personnel. Warning Be sure to observe electrostatic discharge (ESD) precautions while working inside the unit. To complete this procedure, you will need the following items: • Replacement Fan FAN-9000 • Phillips-head screwdriver • 5/16” nut driver Disassembling the Unit To disassemble the unit, follow these steps: 1. Turn off the system. 2. Disconnect the unit from the power source. 3. Disconnect all cables attached to the unit. 4. Remove the unit from its mounted location by lifting the unit up and off its mounting screws. 5. Place the unit on a static dissipative mat, in a location free from dirt and moisture and protected against static discharge. 6. If you are replacing the maintenance compartment fan, remove the two screws at the left side of the front cover, as shown in Figure 1 on page 2. Note These screws unscrew from the back side of the unit.

CTC Parker Automation A3-06134-100 RS9 CD-ROM Replacement Introduction These instructions explain how to replace a CD-ROM drive in the Power- Station RS9 or the RSPC9 Industrial PC. They include steps for disassem- bling the unit, removing a previously installed drive, installing a new drive, and reassembling the unit. Warning For safety reasons, the unit should be opened only by qualified service personnel. Warning Be sure to observe electrostatic discharge (ESD) precautions while working inside the unit. To complete this procedure, you will need the following items: • CD-ROM Replacement Kit CDR-9000 • Phillips-head screwdriver Disassembling the Unit To disassemble the unit, follow these steps: 1. Turn off the system. 2. Disconnect the unit from the power source. 3. Disconnect all cables attached to the unit. 4. Remove the unit from its mounted location by lifting the unit up and off its mounting screws. 5. Place the unit on a static dissipative mat, in a location free from dirt and moisture and protected against static discharge. 6. Remove the two screws at the left side of the front cover, as shown in Figure 1 on page 2. Note These screws unscrew from the back side of the unit.