PDL Thermosafe 4HS1200WH Manuals

Installation Guide PDL Thermosafe Ceiling Sweep Fans 4HS1200WH, 4HS1400WH, 4HS1200SS, 4HS1400SS, 4JH1200WH, 4JH1400WH, 4JH1200SS, 4JH1400SS IMPORTANT NOTES 1. To ensure proper balance, the blades are a matched set. Do not mix-up the blades with those from another fan. 2. Transport and transit handling may loosen factory fitted cables. Please check and secure terminal screws before installation. PM-119PDLA Rev0 Thank you for purchasing this PDL Thermosafe Ceiling Sweep Fan. You can be assured of years of trouble free operation by installing your ceiling fan carefully according to these instructions. Please read all the instructions before commencing, then complete each step in order from one to eight. INCLUDED WITH YOUR FAN A. Motor Assembly B. 4 x Blades C. 3-Speed Fan Controller D. Screw Pack E. Mounting Bracket F. Instruction Sheet Hangsure Bracket or J-Hook Bracket PROTECTING THE FAN Do not place the motor directly onto a flat surface. The plastic nipple underneath the motor cannot support the weight of the motor and may be easily damaged. When working on the fan, place the motor on the foam packaging with the nipple located in one of the recesses. This protects the nipple and the finish. All electrical work must be carried out by a qualified electrician. CLEARANCES AND ANGLED CEILINGS Hangsure Mounting Suitable for pitched ceilings with a maximum angle of 18.5˚. CONTROLLING A SINGLE FAN This fan has been supplied with a quality PDL 3 Speed Controller that is designed to operate a single fan. 1 1. MOUNTING THE FAN SUPPORT BRACKET Select a suitable location to mount the fan support bracket. The mounting bracket must be fixed to a solid structural member such as a ceiling joist or a securely fixed noggin and be capable of supporting 15 Kg. Additionally it must be located so as to provide the blade with a minimum clearance from the floor of 2100mm, and from other obstructions of at least 300mm. Hangsure Mounting J-Hook Mounting Secure fixing to support 15kg Secure fixing to support 15kg 2. FITTING THE BLADES Discard the plastic spacer as illustrated in the diagram below. Seat the key-slot holes of the blade on the screws of the fan motor. Slide the blade to the right as illustrated until the blade engages in the locking mechanism and secure the blade with screws. Slide up top cowl but allow 5-10mm clearance. Secure with locking screws. Support the Motor Remove Plastic Spacer Slide Blade over Screws Tighten Screws 2 3. CONNECTION OF THE LIGHT FITTING If you are attaching a light fitting to the fan, do so prior to hanging the fan. Note that Clipper Light (CL) and Oyster Light (OL) may be installed in fans which are constructed for this purpose. 1. Unscrew the plastic nipple from the bottom of the motor housing. 2. Pull out the light wires from the motor housing for connection with the lamp holder. 3. Insert the light wires through the adaptor, then screw the adaptor into the motor shaft. 4. Connect the light wires to the lamp holder then screw the lamp holder and the adaptor together firmly. Light Wires Plastic Nipple Lamp Holder Light Wires Adaptor 4. HANGING THE FAN Hangsure Bracket Position the ball-joint in the bracket so that the guide pin on the bracket engages in the slot in the ball-joint. Guide Pin Slot J-Hook Bracket Fit the rubber wheel assembly over mounting Cowling Screw IMPORTANT NOTES For J-Hook Brackets leave a 5-10mm gap between the ceiling and cowling. It’s normal for the cowling to move slightly when the fan is running. This gap prevents damaging the painted ceiling and prevents ticking or clicking noises. 5. CONNECTING THE FAN All PDL Thermosafe Ceiling Sweep Fans are pre-wired to allow for a light to be fitted onto the fan. If you are not fitting a light to the fan, please disregard the light wires. The wires are connected to the incoming wiring as illustrated in the below diagram. 6. CONNECTING THE SPEED CONTROLLER All PDL Thermosafe Ceiling Sweep Fans come complete with a Three Speed Flush Fitting Capacitor Controller. This controller fits to standard 84mm fixing centres the same as a normal switch or power point. Although supplied standard in the vertical format, the mechanism can be rotated through 90 degrees to provide a horizontal format if required. Three is the highest speed, one is the lowest. • Remove switch surround. • Terminate cables as illustrated in the below diagram . Active to Common (C) and Switched Active terminal 3. • Fix controller to wallbox or bracket using screws provided. • Replace switch surround. 3 7. CONNECTIING THE SPEED CONTROLLER WITH A LIGHT SWITCH Requires additional components (not supplied with this fan) including: - PDL 681M20 Switch Mechanism - 2 Gang Grid Plate & Cover (682VH) Fan Only Fan with Light CLEANING INSTRUCTIONS To clean the fan, wipe over with a damp, soap cloth. Do not use scourers or abrasive cleaners. ROTARY SWITCH MECHANISM PDL 681M20 SWITCH MECHANISM ACTIVE A SWITCHED ACTIVE (LIGHT) NEUTRAL N SWITCHED ACTIVE M Red Blue 2 1 3 0 NEUTRAL N SWITCHED ACTIVE M Black ACTIVE A ACTIVE A NEUTRAL N SWITCHED ACTIVE 2 1 3 Red Blue Black C M 8. CHECK FORWARD / REVERSIBLE SWITCH The forward / reversible switch is located on the bottom cowl. Check switch and make sure it is in correct setting, depend on summer or winter season. Note that the forward / reversible switch must be fully engaged for the fan to operate. SUMMER WINTER