-
MANUALE STAZIONE DI SERVIZIO
1
-
Beverly 400 E5
2
-
MANUALE STAZIONE DI
3
-
INDEX OF TOPICS
5
-
GENERAL SAFETY WARNINGS:
8
-
• Remote control and ignition switch
10
-
DIGITAL DISPLAY MEASUREMENT UNIT CON-
11
-
rent value, if no changes were made) -
12
-
THE ASR SYSTEM PREVENTS THE APPLICATION OF
13
-
Manual calibration procedure of the ASR sys-
14
-
8. If the procedure has been completed cor-
15
-
Identification registration numbers are made up of
19
-
Single cylinder 4
20
-
Dimensions and mass
21
-
FRONT FORK OIL
22
-
TRANSMISSIONS AND BRAKES
25
-
Torque in Nm
27
-
PISTON-CYLINDER COUPLING CATEGORY
33
-
Crankshaft-crankcase axial clearance (H)
35
-
- Insert the valves into the cylinder head.
36
-
Measure the unloaded spring length
37
-
- Check the deviation of the valve stem by resting
38
-
- Check that there are no signs of wear on the
39
-
-Using a gauge, measure the cam height.
40
-
Slot packing system
42
-
Tool for fitting steering seats
44
-
punch ø 18
45
-
Punch valve seal rings fitting
46
-
42 x 47 mm Adaptor
47
-
adapter for valve removal tool
48
-
Valve oil seal extractor
49
-
Ø 24 mm adaptor
50
-
Hub cover support stud bolt kit
51
-
EOBD E5 diagnostics cable
52
-
MAINTENANCE ICON OPERATION
54
-
km x 1,000 (mi x 1,000)
55
-
Engine cooling is forced liquid circulation. The
56
-
To top-up the brake fluid, proceed as follows:
58
-
Unscrew the two lever cover fixing screws, from
59
-
Unscrew the central fixing screw of the rear han-
60
-
Remove the brake pump cap and restore the rec-
61
-
2 Bleeder pipe
63
-
Refitting system components
64
-
Ensure the correct orientation of the breather
66
-
A = Left hand turn signal indicator lamp;
68
-
R = Icon for the connection between the smart-
70
-
By keeping the MODE button pressed, upon its
73
-
To set or adjust the time, with vehicle running or
74
-
DISCONNECTING THE BATTERY CABLES WILL RESULT
75
-
right side of the handlebar pressed and wait for
76
-
BY THE LIGHTING OF THE PHONE HEADSET
77
-
The electrical system has nine protection fuses
78
-
Duplication of keys / remote controls
80
-
3. Start procedure in Self-diagnosis > Keyless
81
-
- Undo and remove the central screw from the
85
-
Removing the driven pulley shaft bearing
86
-
- Insert the Seeger ring.
87
-
- Working from the automatic transmission side,
88
-
- Working from the opposite side, supporting the
89
-
- Disengage the upper ring of the specific tool.
91
-
- Remove the discs clearance recovery spring
93
-
THE CLEARANCE RECOVERY SPRING DISCS ARE FIT-
94
-
- Remove the lower spring holder disc complete
95
-
CLUTCH SPRING REVISION
96
-
DISCS WEAR LIMIT
97
-
- Working in reverse order to the removal, insert
98
-
- Insert the semi-trimmed disc with the trimmed
99
-
CLUTCH OUTPUT SHAFT ROLLER CASING IN-
101
-
Pin retaining collar
102
-
- Remove the following components in this order:
103
-
- Remove the two O-rings and replace them, mak-
104
-
- Insert the closure sheath of the torque server
105
-
- Insert the upper cap.
106
-
Removing the driving pulley
107
-
Inspecting the rollers case
108
-
Refitting the driving pulley
109
-
- Insert the transmission cover central screw and
110
-
Removing the hub cover
111
-
- Using a suitable screwdriver use leverage on the
112
-
- Remove the nut and incorporated washer secur-
113
-
Wheel axle bearing removal
114
-
Fitting the Intermediate gear bearing
115
-
- Pay attention to the correct positioning of the
116
-
about 500 cc
117
-
- Act on the extractor to remove the flywheel to-
118
-
Refitting the intermediate gear
119
-
- Insert the flywheel fixing nut.
120
-
- Remove the sleeve connecting the throttle body.
121
-
- Remove the complete mass of the return spring.
123
-
- Disengage the chain from the sprocket and re-
124
-
- Remove the camshaft.
125
-
Removing the cylinder head
126
-
Removing the valves
127
-
- Remove the coil.
129
-
- Remove the retainer rings and remove the piston.
130
-
Refitting the cylinder
131
-
- Check the position of the dowels and insert the
132
-
Inspecting the valves
133
-
- Move the rocker and replace the interested pad,
134
-
Inspecting the springs and half-cones
135
-
Refitting the head and timing system components
136
-
- Working in reverse order, assemble the camshaft
138
-
- Tighten the special screws to the specified tor-
139
-
KEEP THE CRANKSHAFT IN ONE OF THE TWO HALVES
140
-
Refitting the crankcase halves
141
-
- Couple the crankcases, paying particular atten-
142
-
Oil pressure check
144
-
- Remove the flywheel.
145
-
- Remove the oil pump and collect the gasket.
146
-
- Insert the oil pump driving sprocket and chain.
148
-
- Keeping the cover locked in a vice, unscrew the
149
-
- Supporting the ceramic seal properly, remove the
150
-
The ASR system is a driving aid that assists the
155
-
ASR "3" system deactivation icon
156
-
Instrument panel: 68
159
