Planet FSD-504HP Manuals

- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - 1. Package Contents Check the following contents of your package:  Fast Ethernet High Power PoE Switch x 1  User's Manual x 1  Power Adapter x 1  Power Cord x 1  Rubber Feet x 4 If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 4. LED Indicators  System LED Color Function PWR Green Light: Indicates the Switch has power.  Per 10/100Mbps Port LED Color Function PoE Orange Light: Indicates the port is providing 48V DC in-line power. LNK/ACT Green Light: Indicates the link through that port is successfully established at 10/100Mbps. Blink: Indicates that the Switch is actively sending or receiving data over that port. 2. Product Features  RJ-45 Interface �Five 10/100Mbps Fast Ethernet ports  4 ports support 48V DC power to PoE Powered Device  Power over Ethernet  Complies with IEEE 802.3af / at Power over Ethernet Mid-Span PSE  Up to 4 IEEE 802.3af / at devices powered  Supports PoE Power up to 30 watts for each PoE port  60 watts PoE Budget  Auto detects powered device (PD)  Circuit protection prevents power interference between ports  Remote power feeding up to 100m  Switching  Hardware based 10/100Mbps Auto-Negotiation and Auto MDI/MDI-X  Flow control for Full Duplex operation and back pressure for Half Duplex operation  1536Bytes packet size support  Integrates address look-up engine, supporting 1K absolute MAC addresses  Automatic address learning and address aging  Hardware  Desktop palm size  LED indicators for PoE ready / activity and LINK / ACT  One DC 48V power jack 5. Switch Rear Panel Figure 5-1 shows the rear panel of FSD-504HP. 48V DC 1 3 5 4 2 Uplink Figure 5-1: FSD-504HP Rear Panel Power Notice 1. The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninter- rupted Power Supply) for your device. It will prevent you from network data loss or network downtime. 2. In some area, installing a surge suppres- sion device may also help to protect your FSD-504HP from being damaged by un- regulated surge or current to the FSD- 504HP or the power adapter. 3. Switch Front Panel Figure 3-1 shows the front panel of FSD-504HP. PoE PWR 1 2 3 4 5 FSD-504HP ACT LNK 5-Port 10/100Mbps 802.3at PoE+ Switch Figure 3-1: FSD-504HP Front Panel 6. Installing the Switch This part describes how to install your Fast Ethernet High Power PoE Switch and make connections to it. Please read the following topics and follow the procedures as presented. Note This Fast Ethernet High Power PoE Switch does not need software configuration. Desktop Installation To install the Fast Ethernet High Power PoE Switch on desktop, simply follow the following steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the Fast Ethernet High Power PoE Switch. Step 2: Place the Fast Ethernet High Power PoE Switch on desktop near AC power source for its power adapter. Step 3: Keep enough ventilation space between the Fast Ethernet High Power PoE Switch and the surrounding objects. Note When choosing a location, please keep in mind the environmental restrictions dis- cussed in Chapter 7 -- Product Specifica- tions. Step 4: Connect your Fast Ethernet High Power PoE Switch to network devices. A. Connect one end of a standard network cable to the 10/100Mbps RJ-45 ports on the back of the Fast Ethernet High Power PoE Switch. B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers. Step 5: Connect your Fast Ethernet High Power PoE Switch to PoE PD devices. A. Connect one end of a standard network cable to port 2 to port 4 10/100Mbps RJ-45 ports on the back of the Fast Ethernet High Power PoE Switch. B. Connect the other end of the cable to the 802.3at / af powered devices. Office Building Office Building Office Area Warehouse Control Room Speed Dome IEEE 802.3af PoE IP Camera PoE Extender IEEE 802.3af PoE VoIP Phone IEEE 802.3af PoE IP Camera IEEE 802.3at PoE Splitter FSD-504HP DC PoE PoE PoE PoE DC Power Line (DC) 100Base-TX UTP PoE 100Base-TX UTP with PoE

- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - 1. Package Contents Check the following contents of your package: FSD-504HP User’s Manual 51V Power Adapter Power Cord If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. Power PoE IP Camera 100 meters/328 feet FSD-504HP Standard Extend Extend PoE Mode Power PoE IP Camera 250 meters/820 feet FSD-504HP Standard Extend 2. Product Features  RJ45 Interface  Five 10/100Mbps Fast Ethernet ports  4 ports support 51V DC power to PoE powered device  Power over Ethernet  Complies with IEEE 802.3af/at Power over Ethernet end-span + mid-span PSE  Up to 4 IEEE 802.3af/2 IEEE 802.3at devices powered  Supports PoE power up to 30 watts for each PoE port  60-watt PoE budget  Hardware DIP switch for “Standard” and “Extend” mode selection; the “Extend” mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation  Auto detects powered device (PD)  Circuit protection prevents power interference between ports  Remote power feeding up to 100m with standard mode  Switching  Hardware based 10/100Mbps auto-negotiation and auto MDI/MDI-X  Flow control for full duplex operation and back pressure for half duplex operation  1536bytes packet size support  Integrates address look-up engine, supporting 1K absolute MAC addresses  Automatic address learning and address aging  Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing  Hardware  Desktop palm size  LED indicators for PoE ready/activity and LINK/ACT  One DC 51V power jack 4. LED Indicators System LED Color Function PWR Green Light: Indicates the Switch has power. Per 10/100Mbps Port LED Color Function PoE Green Lights to indicate the port is providing 51V DC in-line power to remote PoE PD. LNK/ACT Green Lights to indicate the link through that port is successfully established at 10/100Mbps. Blinks to indicate that the Switch is actively sending or receiving data over that port. 3. Switch Front Panel Figure 3-1 shows the front panel of FSD-504HP. FSD-504HP Standard Extend PWR 1 2 3 4 5 ACT LNK PoE In-use Uplink PoE Figure 3-1: FSD-504HP Front Panel The front panel of FSD-504HP provides one DIP switch for “Standard” and “Extend” mode selections. The detailed descriptions are shown in the following table. DIP Switch Mode Function Standard (default) This mode makes the FSD-504HP operate as a general switch and all ports operate at 10/100Mbps auto-negotiation. Extend �This mode makes the FSD-504HP operate as a VLAN isolation switch and port 1 to port 4 will isolate respectively., Port 1 to port 4 can only communicate with port 5 (uplink port). �This mode also makes the FSD-504HP operate at auto–negotiation 10Mbps speed duplex mode only, but the delivery distance of PoE power and network data can reach 250m. 5. Switch Rear Panel Figure 5-1 shows the rear panel of FSD-504HP. 51V DC Figure 5-1: FSD-504HP Rear Panel Power Notice 1. The device is a power-required device, meaning it will not work till it is pow- ered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime. 2. In some area, installing a surge suppres- sion device may also help to protect your FSD-504HP from being damaged by un- regulated surge or current to the FSD- 504HP or the power adapter. 6. Installing the Switch This part describes how to install your FSD-504HP and make connections to it. Please read the following topics and follow the procedures as presented. Note This FSD-504HP does not need software configuration. Desktop Installation To install the FSD-504HP on desktop, simply follow the following steps: Step 1: Place the FSD-504HP on desktop near AC power source for its power adapter. Step 2: Keep enough ventilation space between the FSD-504HP and the surrounding objects. Note When choosing a location, please keep in mind the environmental restrictions dis- cussed in Chapter 7 -- Product Specifica- tions. Step 3: Connect your FSD-504HP to network devices. A. Connect one end of a standard network cable to the Port-5 of the FSD-504HP that marks with “Uplink”.