PLASMATECH SHARK 45 Manuals

1 pdf manual(s) PLASMATECH SHARK 45 for free download (Document Types: Operator's manual)

PLASMATECH SHARK 45 Operator's manual [PDF] (17 pages)

  • Identifier: id-2390285
  • Brand: PLASMATECH
  • Device: SHARK 45 Welding System
  • Type: PDF
  • Key Aspects: Information on Regular Maintenance, Advanced Configuration Methods, System Limitations and Considerations
  • UPD Date: 23.05.2026
  • Source File: 2414506.pdf
  • Pages: 17
  • Description: Professional user manual for the PLASMATECH SHARK 45.
Pages Preview:
  • 2 ENGLISH EN Introduction 2 Description 2 Usage limits (IEC 60974-1) 2 Technical data 3 How to lift up the machine 3 Opening the packaging 3 Plasma cutting 3 Installation 3 Connection to the electrical supply (Fig. A) 4 Usage norms 4 Connection of plasma torch and ground wire 5 Connection of compressed air 6 Sequence of operations to perform before cutting 6 Maintenance 7 Possible problems and remedies 7 Troubleshooting table 8 Common cutt
  • 3 Technical data The technical data for this equipment is summarized in the ta- ble 1. Table 1 Model SHARK 45 Single-phase power supply 50/60 Hz V 115 ±15% 230 ±15% Mains supply: Zmax Ω (*) Power input @ I2 Max kVA 4,8 5,5 Delayed fuse (I2 @ 100%) A 25 16 Power factor / cosφ 0,97 / 0,99 Efficiency degree η 0,75 0,80 Open circuit voltage (peak) V 460 Current range A 20 ÷ 30 20 ÷ 40 Duty cycle @ 100% (40°C) A - 20 Duty cycle @ 60% (40°C) A 20 30 Du
  • 4 Connection to the electrical supply (Fig. A) Connection of the machine to the user line (electrical cur- rent) must be performed by qualified personnel. Before connecting the cutting equipment to the mains sup- ply, check that the data on the machine plate correspond to the supply voltage and frequency and its main switch is on the “O” position (Pos. 1, Fig. A). Connection to the power supply must be effected using the plug provided with the cutting
  • 5 CONTROL PANEL (Fig. C) Pos. 1 Cutting current adjustment knob. Pos. 2 White LED - power supply on. When on the system is powered and ready for use. Pos. 3 Yellow LED with dual function and protection: THER- MOSTAT and OVERCURRENT. • THERMOSTAT function: this LED shines to indi- cate that the overheating protection has cut in be- cause the work cycle is not being followed. After several minutes the overheat cut-off rearms auto- matically (and the yellow
  • 6 Connection of compressed air Connect the compressed air hose to the rapid coupling on the back of the plant (Pos. 6, Fig. B). The system must be fed with a constant flow of air at about 5 bar and with a minimum flow capacity of 150 liters per minute. If you have to use industrial compressed air in gas cylinders: • See the manufacturer’s specifications for the procedures for installing and maintaining high pressure gas cylinders. • Examine the valv
Document Preview & Text Transcription (Main Page)
Click to expand and read text
SHARK 45 1020HB83D-EN-09/2021 SN - CW xxxxxx EN Operator’s manual READ CAREFULLY CEA COSTRUZIONI ELETTROMECCANICHE ANNETTONI S.p.A. C.so E. Filiberto, 27 - 23900 Lecco - Italy Tel. ++39.0341.22322 - Fax ++39.0341.422646 Cas. Post. (P.O.BOX) 205 e-mail: [email protected] - web: www.ceaweld.com

PLASMATECH SHARK 45: Welding System Category Related Instructions

4002 S WI CNC
widos 4002 S WI CNC
04.08.2026 94 pages

Kunststoffschweißtechnik WIDOS Einsteinstr. 5 Phone +49 / 71 52 99 39 - 0 W. Dommer Söhne GmbH D-71254 Ditzingen-Heimerdingen Fax +49 / 71 52 99 39 - 40 [email protected] Website: www.widos.de Headquarters: D-71254 Ditzingen-Heimerdingen Country court Stuttgar Comprehensive setup guide for the widos 4002 S WI CNC Welding System. The document explains installation procedures, service procedures, internal layout.

DP-3035
Hobart Welding Products DP-3035
20.08.2026 2 pages

DP-3035 Direct Plug-in Spool Guns For use with the Handler ® 210 G reat for Aluminum MIG Welding to eliminate feeding problems associated with soft aluminum wire. Quick and easy to install on the Handler 210. MIG weld 16 ga. (1.6 mm)–1/4 in. (6.3 mm) alumin Quick reference guide for the Hobart Welding Products DP-3035 Welding System. This guide provides technical guidance on device safety checks, functional overview, installation steps, troubleshooting guides.

MIG180
Uni-Mig MIG180
07.07.2026 10 pages

MIG180 Manual W e l d i n g G u n s O f A u s t r a l i a P t y L t d S U P P O R T I N G A U S T R A L I A N U N I M I G W E L D E R S 1985 85 19 W E L D E R S SINCE UNI-FLAME UNI-FLAME AUTOLIFT 240 Volt Standard MIG / MAG Lift Arc DC/TIG YEARS Warranty Advanced user manual for the Uni-Mig MIG180 Welding System. It covers topics such as operational safety, performance details, technical troubleshooting.

S-32SL
Miller Electric S-32SL
22.07.2026 28 pages

Visit our website at www.MillerWelds.com OM-1546 090 004M August 2000 Processes Description MIG (GMAW) Welding Flux Cored (FCAW) Welding Wire Feeder S-32S And S-32SL Product setup manual for the Miller Electric S-32SL Welding System. This manual outlines firmware installation, performance guidelines, product handling.