PROTRON PLTV-26M Manuals

Not Included Coax Cable Extra RCA Cables Accessories 26M/27M/32M 26/27/32 TOP BACK Remote Power Cord VGA Cable PC Audio RCA Cables Cable AAA Batteries User’s Manual FRONT Start Here Easy Setup Instructions Unpacking the Display and Accessories 1. Remove the contents of the box and place the display in its intended location. PLTV-32M 2. Plug in the display and turn it on. Connecting to Component Video Output Components (Ex: Progressive Scan DVD Player, HDTV Receiver) 1. Using three RCA cables, connect the three component video outputs (Y, Pb, and Pr) to the corresponding jacks in one of the two component video blocks on the display. 2. Using two other RCA cables, connect the right (red) and left (white) audio outputs on the source to the corresponding jacks in the same component video block used above. R L Connecting to a TV Signal Source (Ex: Cable Box, Satellite Receiver, Antenna) 1. Connect a coax cable between the adapter and TV signal source. Note: If you would like to be able to record the TV signal, connect the TV signal source to the recording device, then connect the recording device to the display. Coax Video Source Video Recorder Connecting to Composite Video Output Components (Ex: VCR, DVD Player) 1. Using an RCA cable, connect the composite video output (yellow) on the source device to the corresponding jack in one of the three composite video blocks on the display (AV 1 IN, AV 2 IN, or AV 3 IN). 2. Using two RCA cables, connect the right (red) and left (white) audio outputs on the source to the corresponding jacks in the same composite video block used above. Accessories Box Vertical fold Vertical fold EZPLTV26M_27M_32M.indd 1 10/10/2005 11:04:35 AM Connecting to an Audio System 1. Using two RCA cables, connect the right (red) and left (white) audio outputs in the output block on the display (AV OUT) to the corresponding inputs on your audio system. 2. (OPTIONAL) If you have a powered (amplified) subwoofer, connect a third RCA cable from the SUBWOOFER output on the display to the subwoofer’s (or amplifier’s) input. R L Audio System Powered Subwoofer Installing Batteries in the Remote Control 1. Remove the plastic battery compartment cover from the rear of the remote. 2. Insert two AAA batteries. Be sure to orient the batteries as indicated in the compartment. 3. Replace the cover. Setting up Television Channels 1. Ensure the display is on and the signal source is set to TV. 2. Press to bring up the On-Screen Display (OSD). Contrast Brightness Saturation Hue Sharpness Flesh Tone Color Temperature 50 50 50 50 30 ON Warm Video Select Select Exit Exit MENU 3. Press until the TV menu shows. Auto Search Tuner Mode Channel Skip Channel Name Blue Mute Air ON TV Select Select Exit Exit MENU 4. Press to enter the menu. 5. Press until Tuner Mode is highlighted and then press to select it. 6. Press until the appropriate system is highlighted and then press to select it. Select Air if you are using an antenna, or Cable if you are connecting the display directly to a cable TV wall outlet. 7. Press to return to the TV menu. 8. Press until Auto Search is highlighted and then press to select it. The display will automatically scan all television channels for those with a strong signal. For more information, refer to the User’s Manual. 26M/27M/32M 26/27/32 Operating the Display 1. On the remote, press to turn the display on. 2. Press until the desired signal source is selected (the name of the currently selected signal source will display at the top right of the screen). 3. If the source is set to “TV”, use to change the channel. 4. Use to adjust the volume. Connecting to a PC 1. Set the video resolution on the computer to 1280 × 1024 or less. 2. Connect the included VGA cable between the VGA output on the computer and the VGA input on the display. 3. (OPTIONAL) Using the PC audio cable, connect the computer’s audio output (LINE OUT) to the audio input on the bottom of the display (PC AUDIO IN). © 2005 Protron Digital Corporation EZPLTV26M/27M/32M Vertical fold Vertical fold EZPLTV26M_27M_32M.indd 2 10/10/2005 11:04:51 AM

PLTV-26M/27M/32M 26/27/32" Liquid Crystal Display User’s Manual OMPLTV26M_27M_32M.book Page i Monday, October 10, 2005 11:44 AM Protron PLTV-26M/27M/32M Liquid Crystal Display User’s Manual. © 2005 Protron Digital Corporation. All rights reserved. Under copyright law, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of Protron Digital Corporation. Disclaimer Protron Digital Corporation has reviewed this manual and provides it only as a guide to operation. All statements, technical information, and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be, representations or warranties concerning the products described. Specifications are subject to change without notice. Trademarks Protron is a registered trademark of Prosonic Group Corporation. Protron Digital Corporation 2133 S. Green Privado Ontario, CA 91761 Printed in China OMPLTV26M_27M_32M.book Page ii Monday, October 10, 2005 11:44 AM i Product Cautions TO PREVENT POSSIBLE DANGER, ELECTRIC SHOCK, AND OTHER INJURIES WHEN HANDLING YOUR DISPLAY, PLEASE BE AWARE OF OF ALL WARNINGS AND SAFETY PRECAUTIONS LISTED BELOW. Never spill any liquid of any kind on the display. Never insert anything into the display, where objects can come into contact with high voltage nodes or damage internal components. Do not attempt to service the display yourself. Opening or removing covers exposes high voltage nodes and other hazards. Refer all servicing to qualified service personnel. Do not touch the display or antenna during thunderstorms. Unplug the display during thunderstorms, or if it will not be used for extended periods. Failure to do so may result in electric shock or fire. Before cleaning the display, unplug it from the wall. Use a damp cloth for cleaning. Never use liquid or aerosol cleaners. To prevent overheating and ensure reliable operation, place the display only in a well ventilated location. Avoid cramped or inadequately ventilated locations. Place the display at least 10 cm (4") from walls or other objects. Always keep the vent clean. Never place the display upside down. Note: Read all safety and operating instructions before operating your new display. OMPLTV26M_27M_32M.book Page i Monday, October 10, 2005 11:44 AM ii Conformity and Compliance FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (this can be determined by turning the device off and on), the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, the user should use the shielded signal cable and power cord supplied with the unit. The FCC warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian DOC Notice for Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from a digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. CE Marking and Declaration of Conformity This device complies with the requirements of related European standards, which include the following: • Emission: EN 55022, EN 61000-3-2, EN 61000-3-3 • Immunity: EN 50082-1 • Safety: EN 60950 Low-Voltage Directive (73/23/EEC) OMPLTV26M_27M_32M.book Page ii Monday, October 10, 2005 11:44 AM