Pullman Holt ES2000 Manuals

Save For Future Reference Replacement Parts List Automatic Scrubber Model ES2000 CHASSIS ASSEMBLY Ref. No. Part No. Description Qty. 1 B970553 Chassis 1 2 B525033 Clamp 2 3 B931288 Wheel Axle 2 4 B931668 Skirt Retainer (left or right) 2 5 B931670 Skirt (left or right) 2 6 B931253 Speed Nut 18 7 B932161 Bumper Wheel 2 8 B931300 Caster 2 9 B931284 Wheel Pin 2 10 B931732 Support Arm Boot 2 11 B931537 Support Arm 2 12 B931207 Skirt Front Retainer 2 13 B931615 Front Skirt 2 14 B932276 Spring 2 15 B931305 Elbow 2 16 B230206 6” Wheel 2 17 B931246 Hose Adaptor 1 18 B931261 Hose 1 19 B931517 Needle Valve 1 20 B931694 Solution Valve 115V 1 Brush Lift Mechanism Ref. No. Part No. Description Qty. 1 B205081 Motor Canopy 1 2 B930522 Canopy Spacer 1 3 B700895 3/4 HP Capacitor (not shown) 1 4 B527359 Capacitor Cover (not shown) 1 5A B700790 Drive Brush Motor - 115V 1 5B B700896 Drive Brush Motor - 220V 1 8 B700793 Gear Box 1 9 B931194 Mounting Plate 1 10 B931305 Elbow 1 11 B931286 Shoulder Bolt 3 12 B931244 Bushing 7 13 B931189 Motor Lift Link 1 14 B931662 Eccentric Nut 3 15 B931200 Motor Lift Yoke 1 16 B931186 Motor Pivot Yoke 1 17 B931209 Pedal Pad 1 18 B931191 Pedal Lift 1 19 B931275 Squeegee Trailing Arm 1 20 B931257 Spring 2 21 B932188 Bronze Washer 2 22 B931269 Squeegee Tension Arm 1 23 B931256 Tension Spring 1 24 B931287 Pivot Bolt 1 25 B980322 Tension Spring Clip 1 26 B931272 Pivot Yoke 1 27 B931315 Link 1 28 B931244 Bearing 29 B452004 Pad Drive Brush (not shown) 1

Save For Future Reference This electric scrubber is a high quality, precision made product. All parts used in the manufacturing of this machine have passed rigid quality control standards prior to assembly and an “each unit” final inspection prior to packaging is your assurance of proper assembly. This automatic scrubber was protectively packed to prevent possible damage in transit. Should damage occur, please notify the trans- porting carrier immediately for loss and/or claim. Model ES2000 Automatic Scrubber Operation & Care Instructions MOTOR: This electric scrubber is powered by a 3/4 HP brush motor and a 1 HP by-pass vacuum motor and will operate on 115V/60HZ only. Be sure your power supply agrees with a voltage marked on the name- plate. Voltage decreases of more than 10% will cause the motor to slow down, thus increasing the current draw and opening the circuit breaker. IMPORTANT SAFEGUARDS EXTENSION CORDS: Machines that have 3-wire cords requiring grounding must only be used with extension cords that have 3-prong grounding type plugs and 3-pole receptacles. To determine the minimum wire size required, refer to the chart below: Minimum Wire Size (AWG) of Extension Cord Nameplate Total Extension Cord Length (Feet) Rating-Amps 25 50 75 100 125 150 175 200 0-10.0 18 18 16 16 14 14 12 12 10.1-13.0 16 16 14 14 14 12 12 12 13.1-15.0 12 12 12 12 12 12 12 – Before using an extension cord, inspect it for loose or exposed wires, damaged insulation and defective fitting. WARNING RISK OF FIRE: Do not use with a flammable or combustible liquid to clean a floor. CAUTION Always disconnect power cable from electrical outlet when working on this machine. This electric scrubber must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having equipment grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is prop- erly installed and grounded in accordance with all local codes and ordi- nances. WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet,have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120- Volt circuit, and has a grounded plug that looks like the plug illustrated in sketch A below. A temporary adapter that looks like the adapter illustrated in sketch- es B and C may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded receptacle is not avail- able. The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green colored ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code. GROUNDING INSTRUCTIONS