PURSUIT PRORS Manuals

PRORS Remote Start w/Keyless Entry System Layout For Complete Installation Guide and Technical Support Visit www.voxxuniversity.com. Or Call 1-800-225-6074 2020 Voxx Electronics. All Rights Reserved. 1 2 3 4 1 2 3 4 1 2 3 4 1 Red/Black Igni�on 3 Flex Relay (87) Input 2 Pink Igni�on 3 Flex Relay (30) Output 3 Yellow Starter Output (+) 4 Green Igni�on 2 Output (+) 5 Red Ba�ery 12V (+) 6 Red/White Ba�ery 12V (+) 7 Purple Accessory Output (+) 8 Blue Igni�on 1 Input / Output (+) 8 Pin Start P P P 1 White Data RX 2 Black Ground (-) 3 Blue Data TX 4 Red Ba�ery 12V (+) DBI 1 White Data RX 2 Blue Data TX 3 Black Ground (-) 4 Red Ba�ery 12V (+) RF 1 Blue Data TX 2 White Data RX 3 Black Ground 4 Red Ba�ery 12V (+) Carlink 4 Red Ba�ery 12V (+) 3 Black Ground (-) 2 Blue Data TX 1 White Data RX Weblink 22 Green Unlock Output (-) (NOC 11) 21 Dk. Blue Trunk Output (-) (NOC 9) 20 Red Lock Output (-) (NOC 10) 19 Green/Lt. Blue Ch. 4 AUX Output (-) (NOC 8) 18 Black/White Horn Output (-) 17 Lt. Blue/Green Ch. 5 AUX Output (-) (NOC 7) 16 Red/Black 2nd Unlock Output (-) (NOC 12) 15 Black/Lt. Green Factory Arm Output (-) NOC 6) 14 Brown/Black Brake Input (+) (PIC 6) 13 Black/Blue Factory Disarm Output (-) (NOC 5) 12 Dk. Blue/Black External Ac�va�on Input (-) (PIC 5) 11 Black/Red Pulse A�er Shutdown Output (-) (NOC 4) 10 Orange/Black Parking Brake Input (-) (PIC 4) 9 Black/Yellow Pulse During Crank Output (-) (NOC 3) 8 Green/Yellow Diesel Glow Plug Input (+) (PIC 3) 7 Green/White DomeLight Output (-) (NOC 2) 6 Purple/Brown Door Trigger Input (- / +) 5 Lt. Blue Remote Start Status Output (-) (NOC 1) 4 Green/Orange Tach Input (-) 3 Gray/Black Hood Input (-) (PIC 2) 2 Lt. Green Trunk Trigger Input (-) (PIC 1) 1 Orange Starter Kill Relay / An�-Grind Output (-) 22 Pin Input/Output 1 2 3 4 VOXX FLCART Dock Replacement Part #4120457 Replacement Part #4120463 Replacement Part #4120458 Not Included Not Included Not Included Not Included 1 White Parking Light (30) Output 2 White/Red Parking Light (87) Input 3 Yellow/Black Igni�on Output (+) (Not For Remote Start) 4 Black Ground Input (-) 4 Pin Light P Replacement Part #4360832 This Harness is included with the FLCART. For Wire Informa�on and Diagram Please Refer to Vehicle Specific FlashLogic Install Guide. Visit www.FlashLogic.com for More Informa�on. Not Included 19 17 15 13 11 9 7 5 3 1 2 4 6 8 10 12 14 16 18 20 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 1 3 5 7 2 4 6 8 1 3 2 4 Compatible RF Kits PR1BZ PR1BZLR PR1BTWZ PR5BZ PE2LEDZ PE2LCDZ PE1M2LEDZ PE1M2LCDZ Important Update The default Data Port Protocol of this system is ADS. If using an FLCAN or other external integration module be sure to choose iDatalink 2-Way when flashing. This system will also support DBI. This will require programming Feature Bank 2, Feature 15 to DBI. PRORS Keyless / Remote Start Quick Installation Guide For Complete Installation Guide and Technical Support Visit www.voxxuniversity.com Or Call 1-800-225-6074 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp 1 Lock / Unlock Func�on 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL 2 Igni�on Lock OFF ON 3 Igni�on Unlock OFF Unlock All Unlock Driver 4 Exterior Illumina�on OFF With Arm With Disarm With Arm & Disarm 5 Auto Relock OFF ON 6 Auto Arming / Locking N/A 7 No�fica�on Sound N/A 8 Horn Timing 16ms 30ms 40ms 50ms 10ms 9 Valet Override Method N/A 10 Driver Priority Unlock OFF ON 11 Silent Choice OFF From Transmi�er OEM Style 12 Security Profile OFF OEM Security Security w/ OEM RS 13 Door Trigger Input Negative Posi�ve 14 Park Light / Trunk Swap OFF ON 15 Data Port Protocol ADS DBI 16 Dome Light Delay Timer OFF / Program 15sec 30sec 45sec 60sec 120sec 17 Alarm Trigger Legnth 30sec 45sec 60sec 90sec 120sec 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp 1 Defrost Output Pulsed 10min RS Run�me 2 RS Start No�fica�on ON OFF 3 RS Run�me 15min 20min 45min 60min 5min 10min 4 RS Parking Lights Steady Flashing 5 Engine Confirma�on Tach Voltage Data Hybrid 6 Voltage Level >0.5v B4 Start <0.5v B4 Start 7 Igni�on 2 Output Ignition Accessory Start 8 Igni�on 3 Output Ignition Accessory Start 9 Accessory Output Accessory Igni�on Start 10 Transmission Auto Manual 11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec 12 Diesel Delay OFF Diesel 5 Diesel 10 Diesel 15 Diesel 20 Diesel 30 13 Temperature Start OFF 14°F 5°F 0°F -4F -14F 14 Crank Dura�on Averaging Preset 15 RS Shock Override Shunt until Clear Shunt RS Cycle Shunt From TX 16 Turbo Timer OFF 3min 5min 10min 17 Start Ac�va�on Two Press One Press Three Press 18 RS Lock Func�on No Change UL Before L A�er UL Before Start Lock A�er Start 19 Factory Disarm Output Single Pulse Double Pulse 350ms 500ms 800ms Same As Bank 2, F1 20 Addi�onal Unlock Pulse No Pulse IGN, ACC, GWR IGN,ACC,GWR,PASD Features Feature Bank 2 Op�ons Features Feature Bank 3 Op�ons Negative Output Control (NOC) AUX Output Control Negative output control allows any NOC to be programmed for any one of nineteen (19) options. This feature is accessible via FlashLogic Weblink or Weblink Mobile. Any AUX output can configured using the AUX Control Menu. This feature is only accessible via FlashLogic Weblink or Weblink Mobile. The Feature Banks below can also be programmed using the FlashLogic Weblink or Weblink Mobile. 10 Second Pulse 15 Second Pulse 20 Second Pulse 30 Second Pulse Push & Hold Latch ON/OFF Latch 10min w/ RS Latch Run�me 5 Second Pulse 1 Second Pulse Headlight Defrost LED Ch. 4 AUX Ch. 5 AUX Ch. 6 AUX Ch. 7 AUX Factory Disarm Factory Arm Accessory Pulse During Crank Pulse A�er Shutdown Lock Unlock 2nd Unlock Trunk Remote Start Status Igni�on Ground While Armed Ground While Disarmed Domelight REV. B 2020 Voxx Electronics. All Rights Reserved. Remote Programming The PRORS does not include an RF remote kit. The RF remote kit Includes two (2) remotes, one (1) antenna, and one (1) cable. When added, remotes must be programmed to the system. Remote Programming is located in Feature Bank 1. To enter Remote Auto Programming: 1. Turn the ignition key to ON. 2. Press and release the valet button three (3) times. System will beep and flash the parking lights one (1) time. Press the lock button on each remote. The system will beep one (1) time to indicate the remote has been programmed. If programming one (1) button remotes, press the Start button. Only primary remote functions are auto programmed. This Includes Lock, Unlock, and Trunk/Start. If using AUX output control, you must manually program the AUX output channels to the remote. Please see the complete installation guide for manual remote programming instruction. Note: If programming 2-Way remotes, wait for the remote to beep before programming additional remotes. This beep is confirmation that a 2-Way response has been received from the main module. Feature Programming The PRORS Feature Banks can be programmed by using the valet button and remote. To enter Feature Bank programming: 1. Turn the ignition key to ON. 2. Press and release the valet button three (3) times. System will beep and flash lights one (1) time for Feature Bank 1, Remote Programming. 3. Cycle ignition key OFF/ON. System will beep and flash lights two (2) times for Feature Bank 2. 4. Press valet button to cycle features. LED will flash to display feature number. 5. Press lock button to cycle options. System will beep to indicate option number. 6. Cycle ignition key OFF/ON. System will beep and flash lights three (3) times for Feature Bank 3. 7. Press valet button to cycle features. LED will flash to display feature number. 8. Press lock to cycle options. System will beep to indicate option Number. Tach Programming The installer must manually configure the Engine Confirmation method in Feature Bank 3, Feature 5. The default method is “Tach”. When using the default “Tach” method, the vehicle tach rate must be programmed. To enter tach rate programming: 1. Turn the ignition key ON. 2. Press and release the valet button three (3) times. 3. Turn the ignition key OFF. 4. Press and hold valet button. 5. While holding valet button, start the engine using the key. 6. Hold the valet button for approximately ten (10) seconds. If connected to the vehicle Tach source, the system will flash the parking lights one (1) time every second. 7. Release the valet button. The system will turn on the parking lights for two (2) seconds to indicate the tach rate is programmed. The tach rate can also be programmed without the use of a valet button. This is helpful when using the OEM remote of CarLink system to control this module. To program the tach rate without a valet button: 1. Turn the ignition key to the ON position and start the vehicle’s engine. 2. Wait for Engine RPM to lower to a normal idle. 3. Press and hold the vehicle’s brake pedal. 4. Press the LOCK button on the OEM remote or the Carlink App. Note: Programming tach signal via OEM or Telematics control is only available on Firmware v1.47 or Higher. Data Protocol Selection The default data port protocol of this model is ADS (iDatalink 2-Way). This model is capable of detecting the correct data port protocol (ADS or DBI) and automatically configuring Feature Bank 2; Feature 18. To initialize the detection procedure: 1. Press and hold the valet button. 2. Cycle the vehicle’s Ignition ON/OFF two (2) times. 3. Release the valet button. The system will automatically detect and set the correct data port protocol, ADS or DBI. Note: This feature is only available on module firmware v2.0 or higher. Notifications 1 Run�me Expired 2 Remote Shutdown 3 Brake On 4 Manual Mode 5 Hood Open 6 Low / No Tach 7 Tach Programming 8 High Tach OEM Security The PRORS can provide OEM level security. The system will monitor all entry zones (Door, Hood, And Trunk). When an entry zone is detected the system will beep the vehicle horn and flash the parking lights. This feature must be activated in Feature Bank 2, Feature 12. Chirp Delete System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature Bank programming. 1. Turn the ignition key ON/OFF. 2. Press and release the valet button three (3) times. The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This feature will not affect alarm trigger or programming. User Programmable LED System LED notifications can be turned ON or OFF without entering Feature Bank programming. 1. Turn the ignition key ON/OFF, ON/OFF. 2. Press and hold valet button for five (5) seconds. The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect LED flash during programming. Remote Start If the remote start fails to start the vehicle, the system will flash the vehicle parking lights to indicate the cause. Dome Delay Programming This system can be programmed to ignore the vehicle’s theater dimming dome light. This feature will be used when connecting the door trigger input to the dome light circuit for alarm trigger. Start with all doors closed and the vehicle dome light off. 1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid. 2. Open and close the driver door. The system will monitor the dome light circuit. When the dome light turns off the system will set the delay time and add an additional two (2) seconds. Dome Delay Reset 1. Key ON/OFF, ON/OFF, ON/OFF. 2. Press and hold valet button for five (5) seconds. The system will beep one (1) time to indicate reset is complete. Programmable Input Control Programmable Input Control allows any PIC be configured to one of the options listed below. This feature is accessible via FlashLogic Weblink or Weblink Mobile. N.C. Door Trigger External Start Ac�va�on Pre-Warn Shock Trigger Diesel Glow Plug Door Trigger Full Shock Trigger Trunk Trigger Parking Brake Hood Trigger Brake