Quoizel HC1612IB Manuals

Package Contents Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445 Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers,electrical tape, safety glasses. Bulb Recommended: EstimatedAssembly Time: Preparation: (2) Medium Base 60W bulbs Maximum,Alternate bulb (2) 13W CFLMaximum. 20-30 minutes Identify and inspectall parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contactcustomer service for replacement parts. Warnings and Cautions 1of2 Assembly Instruction Sheet #IS-HC1612IB For Style HC1612IB Thank you for purchasing a Quoizel product. Need assistance withparts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com 2014 QuoizelInc. March2014 Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result. B Cage x 1 Flat Washer x 1 C Glass Panel x 4 F Hex Coupling x 1 Stem with Hex Nut x 1 G Hardware Contents AA Crossbar x 1 A Ceiling Canopy x 1 H Knurled Nut x 1 BB CC DD Lock Washer x 1 Hex Nut x 2 Nipple x 1 AA BB CC DD CC A Step A Step D STEP 1 Install Crossbar - A. Attach the Crossbar (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug . . Figure 1 Outlet Box Outlet Box Screw (not included) Green Ground Screw AA Figure 2 Lock Washer x 1 I Finial x 1 STEP 2 Install Nipple to Crossbar - * Pliers is required for this step. A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA). B. Position the center hole of the Ceiling Canopy (A) over the end of the Nipple (DD). Adjust the Nipple (DD) so approx 0.375” of the Nipple (DD) is protruding from the mounting hole on the Ceiling Canopy (A). This adjustment may take a few tries. C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place. D. Thread another Hex Nut (CC) onto the end of the Nipple (DD). Thread this Hex Nut (CC) on just enough so the inside surface of the Ceiling Canopy (A) rests against it. * You may have to trial fit the Ceiling Canopy (A) one more times to insure this distance also. This Hex Nut (CC) is needed here to prevent you from crushing down the center of the Ceiling Canopy (A). E. Refer to Step 3 for wire connections. F. Attach the Ceiling Canopy (A), the Flat Washer (F) and one Lock Washer (BB) over the end of the Nipple (DD) as shown. Secure by threading the Hex Coupling (H) onto the Nipple (DD) and tighten until snug. BB STEP 3 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors. B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire from fixture. D Lock Screw x 8 E Tab x 8 J K F H 2of2 Thank you for purchasing a Quoizel product. Need assistance withparts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com 2014 QuoizelInc. March2014 Figure 6 STEP 5 - Install Bulb A. This fixture uses standard bulb with medium base. Maximum 60 watts. B. Insert bulb and screw snugly into place. Figure 5 Bulb White wire from supply Ribbed side wire from fixture Black wire from supply (or Red) Smooth side wire from fixture Ground wire from supply Ground wire from fixture Figure 3 HC1612IB PART NUMBER 11612IBH G1422PA G1421PA M1033FIIB NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION BASE IMPERIAL BRONZE FLUSHMOUNT BOTTOM PANEL 9-3/4"SQ X 3/8"D SIDE PANEL 5-1/8"H X 9-3/4" FINIAL 0.37 H X 1.12 " " IMPERIAL BRONZE REQ. 1 1 4 1 NO. (2) 60W Bulbs (Not Supplied) Medium Base 1 FINISH: IMPERIAL BRONZE ONE LIGHT SHOWN FOR ILLUSTRATION PURPOSE ONLY. C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth side Wire from fixture. D. Connect Ground Wire from the Outlet Box to Ground Wire from fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. STEP 4 - Install Stem with Hex Nut A. Thread the Hex Nut end of the Stem (I) into the Hex Coupling (H). By using pliers, thread the Hex Nut against the Hex Coupling (H) and hand tighten until snug. Figure 4 Socket B C E D STEP 7 - Install Cage A. Place the Cage (B) over the end of the Stem (I) and secure with the Knurled Nut (J). Hand tighten until snug. B. Thread the Finial (K) onto the end of the Stem (I) and hand tighten until snug. Your fixture is now assembled and ready to use. Enjoy! Figure 7 STEP 6 - Install Glass Panels A. Insert the Glass Panels (C) into the Cage (B). Attach the Tabs (E) to the top edge of the Glass Panels (C) and secure with the Lock Screws (D). Hand tighten until snug. 10” SQ. 8” 11.5” 11.5” 2 3 4 K J B I 1 2 3 4 H I