Quoizel SNNL8409K Manuals

Package Contents 1of2 Assembly Instruction Sheet #IS-SNNL8409_R1 For Styles SNNL8409K and SNNL8409PN A Crossbar Assembly x 1 Please go to for product cleaning tips. Go to the selection. LED 16W 20-30 minutes Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts. www.quoizel.com Care + Maintenance Light Source: EstimatedAssembly Time: Preparation: Fixture can only be mounted in the direction indicated on page 2. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. B Fixture Body x 1 STEP 1 Install Crossbar Assembly - A. Pass the supply wires through the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included). Tighten until snug. Supply Wires with Ground Wire Outlet Box Screws (not included) Outlet Box Figure 1 A STEP 2 Fit Backplate to Crossbar Assembly - A. on Fixture Body (B) to the Remove mounting balls from the Crossbar Assembly (A). Fit the backplate Crossbar Assembly (A) and secure with mounting balls. Note: The backplate should be snug against the wall and the mounting balls. If on Fixture Body (B) not, adjust the length of the mounting screw on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the Figure 2 crossbar until the correct length is achieved. Once the backplate on Fixture Body (B) is secure, remove the mounting ball and Fixture Body (B) and proceed to Step 3. Mounting Screw B Mounting Ball A Backplate Hex Nut and Lock Washer Mounting Screw B Mounting Ball A Backplate Exterior Grade Caulk Backplate Warnings and Cautions Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Figure 4 STEP 4 Install Fixture Body - A. Position the backplate and Fixture Body (B) onto the Crossbar Assembly (A). Place the holes in the backplate over the mounting screws. Secure the Fixture Body by using the mounting balls and hand tighten the mounting balls until snug. Figure 5 STEP 5 - Apply Silicone Sealer A. Make sure exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, caulk over top of backplate and down other side. Do not caulk bottom of fixture backplate to ensure proper moisture drainage. Your fixture is now assembled and ready to use. Enjoy! STEP 3 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. Figure 3 Green Ground Screw on the Crossbar White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box Ground wire from Fixture 2017 QuoizelInc. Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com RevisedDate:2017-11-03 2of2 HOW TO REPLACE GLASS PANELS Allen Screw Glass Panel Cage A. Fixture Hood. Separate Quick Connector and then remove Cage with Glass Panels from the fixture. B. Unscrew Screws from the Cage and remove LED Module and Heat Sink, Glass Holders. Replace Glass Panels from the Cage and then re-install Glass Holders, LED Module and Heat Sink . Secure with removed Screws. C. Connect Quick Connectors. Attach Cage with Glass Panels back onto the Fixture Hood and secure with Allen Screws. Unlock Allen Screws on the Glass Holder Fixture Hood LED Module and Heat Sink Quick Connector Screw SNNL8409K FINISH: MYSTIC BLACK SNNL8409PN FINISH: PALLADIAN BRONZE NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" Fixture can only be mounted in the direction indicated 15” 8” 6” 10.5” 9.5” 4.5” OUO ZEL 2017 QuoizelInc. Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com RevisedDate:2017-11-03

1of2 For Styles SNNL8409K and SNNL8409PN Please go to for product cleaning tips. Go to the selection. LED 16W 20-30 minutes Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase. www.quoizel.com Care + Maintenance Light Source: EstimatedAssembly Time: Preparation: Fixture can only be mounted in the direction indicated . Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. STEP 2 Fit Backplate to Crossbar Assembly - A. on Fixture Body (B) to the Remove mounting balls from the Crossbar Assembly (A). Fit the backplate Crossbar Assembly (A) and secure with mounting balls. Note: The backplate should be snug against the wall and the mounting balls. If on Fixture Body (B) not, adjust Figure 2 Mounting Screw B Mounting Ball A Backplate Hex Nut and Lock Washer Mounting Screw B Mounting Ball A Backplate Exterior Grade Caulk Backplate Warnings and Cautions Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Figure 4 STEP 4 Install Fixture Body - A. Position the backplate and Fixture Body (B) onto the Crossbar Assembly (A). Place the holes in the backplate over the mounting screws. Secure the Fixture Body by using the mounting balls and hand tighten the mounting balls until snug. Figure 5 STEP 5 - Apply Silicone Sealer A. Make sure exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, caulk over top of backplate and down other side. Do not caulk bottom of fixture backplate to ensure proper moisture drainage. Your fixture is now assembled and ready to use. Enjoy! STEP 3 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (D) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. Figure 3 Green Ground Screw on the Crossbar White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box Ground wire from Fixture 2018 QuoizelInc. ReleasedDate:2019-08-09 visit us on-line at www.quoizel.com Installation Guide #IS-SNNL8409 the length of the mounting screw on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the backplate on Fixture Body (B) is secure, remove the mounting ball and Fixture Body (B) and proceed to Step 3. Package Contents B Fixture Body x 1 STEP 1 Install Crossbar Assembly - A. Pass the supply wires through the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (C). Tighten until snug. Supply Wires with Ground Wire Outlet Box Figure 1 A Crossbar Assembly x 1 A Alternate Mounting Screw x 2 E Outlet Box Screw x 2 C Wire Connector x 3 D C 2of2 2018 QuoizelInc. visit us on-line at www.quoizel.com ReleasedDate:2019-08-09 HOW TO REPLACE GLASS PANELS A. Fixture Hood. Remove Cage with Glass Panels from the fixture. B. Unscrew Screws from the Cage and remove Glass Holders. Replace Glass Panels from the Cage and then re-install Glass Holders. Secure with removed Screws. C. Attach Cage with Glass Panels back onto the Fixture Hood and secure with Allen Screws. Unlock Allen Screws on the Figure 6 Allen Screw Glass Panel Cage Glass Holder Fixture Hood Screw