Quoizel WVR1612EK Manuals

1of2 For Style WVR1612EK Package Contents Warnings and Cautions Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. A F Crossbar Assembly x 1 Please go to for product cleaning tips. Go to the selection. (2) B10 Candelabra Base bulbs 60W Maximum, Candelabra BaseT8 Vintage Bulbs are recommended, bulbs not included.. 20-30 minutes Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase. www.quoizel.com Care + Maintenance Light Source: EstimatedAssembly Time: Preparation: Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Installation Guide #IS-WVR1612EK C Fixture Body x 1 B Lock Screw x 2 2018 QuoizelInc. ReleasedDate:2018-10-08 visit us on-line at www.quoizel.com Cage x 1 Hex Nut and Lock Washer Nipple Green Ground Screw Outlet Box Screw (not included) Mounting Ball Figure 2 D Square Glass Panel x 1 E Side Glass Panel x 4 STEP 1 Install Glass Panels - A. Place the Square Glass Panel (F) into the bottom of the Cage (D) with the beveled edge on the bottom. Secure by pressing tabs in the bottom edge of the Cage (D) to the Square Glass Panel (F). B. Place Side Glass Panel (E) between the Square Glass Panel (F) and the Cage (D) with beveled edge outside. Secure by pressing tabs on the top edge of the Cage (D) to top edge of Side Glass Panel (E). E F D Tab Tab Figure 1 A C STEP 3 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. Green Ground Screw on the Crossbar White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box Ground wire from Fixture Figure 3 STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust the length of the Nipple A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included), tighten until snug B. Adjust the hex nut and lock washer underside of the crossbar to the middle of the nipple. C. Remove the mounting ball from the nipple. Place the Fixture Body (C) over the nipple against the ceiling to determine the correct position of the nipple. Thread the mounting ball onto the nipple. Adjust the nipple to allow the Fixture Body (C) to rest against the ceiling when held in place by the mounting ball. D. Remove the mounting ball and the Fixture Body (C). Tighten the lock washer and the hex nut against the crossbar to secure in place. . 2of2 2018 QuoizelInc. ReleasedDate:2018-10-08 visit us on-line at www.quoizel.com Figure 4 C Nipple Mounting Ball STEP 5 Install Bulbs and Cage - A. Insert bulbs onto sockets and screw snugly into place. B. Place the Cage (D) onto the Fixture Body (C) and secure with Lock Screws (B). Hand tighten until snug. Your fixture is now assembled and ready to use. Enjoy! T8 Vintage Bulb (Recommended but not included) C D Socket WVR1612EK FINISH: EARTH BLACK NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" 10” SQ. 4” B Figure 5 12” SQ. STEP 4 Install Ceiling Canopy to Crossbar - A. Attach the Fixture Body (C) over the end of the nipple and secure with previously removed mounting ball. Hand tighten until snug.