Rane MLM 103 Manuals

Manual-1 MLM 103 MIC/LINE MIXER OPERATORS MANUAL WEAR PARTS: This product contains no wear parts. QUICK START If you don't get any further, at least read this section to get the best gain structure out of the MLM 103. INPUTS 1 through 6 may be microphone or line level. The choice between the two is made by setting the Input’s LINE push-button on the rear panel. Push the PHANTOM POWER button (when needed) for each pair of Inputs. Using a screwdriver, adjust the TRIM for each Input so that the front panel OL LED illuminates only occasionally during extreme peaks. The three-band Equalizer settings will influence this, so keep an eye on the OL when making EQ adjustments. Now adjust the LEVEL for each Input. Assign each Input to the desired Output by pushing any combination of the A, B, or AUX ASSIGN buttons. - 12 0 + 12 - 12 0 + 12 -20 -10 MIC / LINE MIXER +2 -7 -4 0 -2 +7 +4 +10 -20 -10 +2 -7 -4 0 -2 +7 +4 +10 2 1 5 3 4 6 7 10 8 9 2 1 5 3 4 6 7 10 8 9 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 10 0 2 4 8 6 10 0 2 4 8 6 - 12 0 + 12 - 12 0 + 12 ASSIGN A B LOW HIGH MID INPUTS ASSIGN MONO A / B POWER OUTPUTS 1 2 3 4 5 6 7 / 8 9 / 10 A B AUX MLM 103 LEVEL OL AUX AUX ASSIGN A B LOW HIGH MID LEVEL OL AUX ASSIGN A B LOW HIGH MID LEVEL OL AUX ASSIGN A B LOW HIGH MID LEVEL OL AUX ASSIGN A B LOW HIGH MID LEVEL OL AUX ASSIGN A B LOW HIGH MID LEVEL OL AUX LOW HIGH MID LEVEL OL ASSIGN MONO A / B AUX LOW HIGH MID LEVEL OL INPUTS 7/8 and 9/10 are stereo line level Inputs. Assign each stereo input to the desired output as follows: When the ASSIGN button is engaged and the MONO but- ton is not engaged, INPUT 7 (or 9) is routed to the A Output, while INPUT 8 (or 10) is routed to the B Output. When the both the ASSIGN and MONO buttons are en- gaged, both Inputs of 7/8 (or 9/10) will route to both the A and B Output. The AUX ASSIGN button is always a mono mix of the stereo channel.

Manual-1 MLM 103 MIC/LINE MIXER OPERATORS MANUAL WEAR PARTS: This product contains no wear parts. MLM 103 CONNECTION INPUTS The MLM 103 has ten balanced Euroblock Inputs. Use only shielded cable. For best noise rejection use two-conduc- tor-plus-shielded wire, even for unbalanced operation. Connect the non-inverting (positive) audio lines to the “+” terminals, and the inverting (negative) lines to the “–” terminals. Connect the shields to the “ground” terminals. For those installations where the MLM 103’s internal shield-to-chassis connection causes interference, connect the shields directly to chassis PEM nuts directly above each pair of Euroblock connectors. Be sure to bite through the paint with the star washer and keep the shields wrapped around the audio conductors as mush as possible. For the “theoretical” best ElectroMagnetic Interference (EMI) immunity, connect the shields at both ends of the cables. (For more information on connections, see RaneNote 110, “Sound System Intercon- nection” later in this manual or on Rane’s web site.) MONO INPUTS 1-6 can accept either mic or line level sources. When connecting line level signals, push the rear panel button in for LINE. For mic signals, be sure the button is in the MIC (out) position. STEREO INPUTS 7/8 and 9/10 accept line level stereo and mono sources. OUTPUTS The MLM 103’s OUTPUTS (and DIRECT OUTPUTS) are balanced. The same wiring conventions as the Euroblock Inputs apply. QUICK START If you don't get any further, at least read this section to get the best gain structure out of the MLM 103. INPUTS 1 through 6 may be microphone or line level. The choice between the two is made by setting the Input’s LINE push-button on the rear panel. Push the PHANTOM POWER button (when needed) for each pair of Inputs. Using a screwdriver, adjust the TRIM for each Input so that the front panel OL LED illuminates only occasionally during extreme peaks. The three-band Equalizer settings will influence this, so keep an eye on the OL when making EQ adjustments. Now adjust the LEVEL for each Input. Assign each Input to the desired Output by pushing any combination of the A, B, or AUX ASSIGN buttons. INPUTS 7/8 and 9/10 are stereo line level Inputs. Assign each stereo input to the desired output as follows: When the A/B ASSIGN button is engaged and the MONO button is not engaged, INPUT 7 (or 9) is routed to the A Output, while INPUT 8 (or 10) is routed to the B Output. When the both the A/B ASSIGN and MONO buttons are engaged, both Inputs of 7/8 (or 9/10) will route to both the A and B Output. The AUX ASSIGN button is always a mono mix of the stereo channel.

Manual-1 MLM 103 MIC/LINE MIXER OPERATORS MANUAL WEAR PARTS: This product contains no wear parts. MLM 103 CONNECTION INPUTS The MLM 103 has ten balanced Euroblock Inputs. Use only shielded cable. For best noise rejection use two-conduc- tor-plus-shielded wire, even for unbalanced operation. Connect the non-inverting (positive) audio lines to the “+” terminals, and the inverting (negative) lines to the “–” terminals. Connect the shields to the “ground” terminals. For those installations where the MLM 103’s internal shield-to-chassis connection causes interference, connect the shields directly to chassis PEM nuts directly above each pair of Euroblock connectors. Be sure to bite through the paint with the star washer and keep the shields wrapped around the audio conductors as much as possible. For the “theoretical” best ElectroMagnetic Interference (EMI) immunity, connect the shields at both ends of the cables. (For more information on connections, see RaneNote 110, “Sound System Intercon- nection” later in this manual or on Rane’s web site.) MONO INPUTS 1-6 can accept either mic or line level sources. When connecting line level signals, push the rear panel button in for LINE. For mic signals, be sure the button is in the MIC (out) position. STEREO INPUTS 7/8 and 9/10 accept line level stereo and mono sources. OUTPUTS The MLM 103’s OUTPUTS (and DIRECT OUTPUTS) are balanced. The same wiring conventions as the Euroblock Inputs apply. QUICK START If you don't get any further, at least read this section to get the best gain structure out of the MLM 103. INPUTS 1 through 6 may be microphone or line level. The choice between the two is made by setting the Input’s LINE push-button on the rear panel. Push the PHANTOM POWER button (when needed) for each pair of Inputs. Using a screwdriver, adjust the TRIM for each Input so that the front panel OL LED illuminates only occasionally during extreme peaks. The three-band Equalizer settings will influence this, so keep an eye on the OL when making EQ adjustments. Now adjust the LEVEL for each Input. Assign each Input to the desired Output by pushing any combination of the A, B, or AUX ASSIGN buttons. INPUTS 7/8 and 9/10 are stereo line level Inputs. Assign each stereo input to the desired output as follows: When the A/B ASSIGN button is engaged and the MONO button is not engaged, INPUT 7 (or 9) is routed to the A Output, while INPUT 8 (or 10) is routed to the B Output. When the both the A/B ASSIGN and MONO buttons are engaged, both Inputs of 7/8 (or 9/10) will route to both the A and B Output. The AUX ASSIGN button is always a mono mix of the stereo channel.