Resolution RE159 Manuals

360 Degree PIR Motion Sensor 360 PIR Motion Sensor alarms when motion is sensed. It is a commercial battery-powered ceiling mount sensor with a 360 degree detection range. Features •  360° detection range with 62 distinct detection zones •  Range up to 40 feet in diameter •  Selectable pulse count 2 or 4 •  Designed for commercial application •  5 year warranty Enroll by placing the panel into wireless enrollment mode and tripping the sensor’s enrollment sequence. Interlogix® , DSC®, Qolsys® and Cryptix™ variants can be enrolled by pulling the battery tab or by tampering the unit. Honeywell ® and 2GIG™ variants can be enrolled by tripping the unit three times (tamper or motion) or by holding the tamper down and powering the unit up by pulling the battery tab. Honeywell and 2GIG sensors must be enrolled as a “Loop1” sensor. Alternatively, all variants of the motion sensor can be enrolled by entering its serial number into the panel. Install by screwing two #8 screws into the ceiling, leaving 1/4 inch of thread exposed. Next, slide the back plate over the screws and rotate the back plate. Screw the third #8 screw through the wall tamper into the ceiling, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Then, insert the square nut into the square slit of the cover and start threading the #4 screw into the side of the cover. Close the cover and conduct a walk test. After walk testing, take the unit out of walk test mode and close the cover again. Finally, finish threading the #4 screw until it is snug. Use your panel’s installation guide to verify proper system setup. I N S T A L L G U I D E I Mounting Tips •  Avoid direct sunlight •  Avoid facing directly to AC or heating vents •  Avoid vapor or high humidity •  Avoid curtains, screens, etc. from blocking detection •  Do not install outdoors

Indoor 40 PIR Motion Sensor PIR Motion Sensor alarms when motion is sensed. It is a commercial battery-powered wall mount sensor with an 85 degree detection range. Features •  85° detection range with 78 distinct detection zones •  Range up to 40 feet •  Selectable pulse count 2 or 4 •  Designed for commercial applications •  5 year warranty Enroll all variants by entering their serial numbers into the security panel. Alternatively, the sensor can be enrolled in one of the following ways: Cryptix™, DSC®, Qolsys® and Interlogix® variants are enrolled by placing the panel into enrollment mode, and then pulling the battery tab or tampering the device. Honeywell® and 2GIG™ variants are enrolled by placing the panel into wireless enrollment mode and either removing the battery tab while holding the tamper, or by tripping the device three times. These sensors must be enrolled as a “Loop 1” sensor. Install by screwing two #5 screws through the unit’s mounting knockouts. Use 2 of the 3 mounting knockouts in the center of the unit’s back to mount on a flat wall. Use 2 of the 4 corner knockouts to mount the unit in the corner of a room. Mount the sensor 5ft to 8 ft (1.5m-2.4m) high. Screw the third #8 screw through the wall tamper knockout into the wall, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Enroll the sensor using the instructions above. Close the cover and conduct a walk test. After testing, take the unit out of walk test mode and close the cover again. Finally, finish threading the white #4 screw until it is snug. Use your panel’s installation guide to verify proper system setup. I N S T A L L G U I D E I Mounting Tips •  Avoid direct sunlight •  Avoid facing directly to AC or heating vents •  Avoid vapor or high humidity •  Avoid curtains, screens, etc. from blocking detection •  Do not install outdoors •  Mounting height 5ft-8ft (1.5m-2.4m)