REVENTON VELO Silver Series Manuals

Domestic axial fan with throttle VELO and VELO Silver series User Manual Introduction Thank you for choosing our product. Reading of this manual is required for proper use of the device and absolute observance to its guidelines is fundamental condition of security. All users of the device should have free access to the manual and in case of resale, the instruction must be attached to the product. Package contents - domestic axial fan VELO - user manual Transport and storage The fan should be transported and stored in the original packaging in a dry place protected from contamination, until it is installed. Moreover, the fan should be protected from the shocks. Application Axial fans from the VELO series are designed for wall mounting. They are used for ventilation of small spaces such as a bathroom or kitchen. The device comes in two colors - white or silver (VELO Silver version). Construction of the device 1 – Panel 2 – Sensor 3 – Casing 4 – Motor 5 – Rotor ,w 6 – Throttle frame 7 – Throttle 8 – Fastening ring 9 - Frame Dimensions (in mm) MODEL ØA B C D VELO 100 & VELO SILVER 100 100 150 90 35 VELO 150 & VELO SILVER 150 150 193 100 35 Technical data MODEL VELO 100 & VELO Silver 100 VELO 150 & VELO Silver 150 Maximum aiflow [m3/h] 95 240 Maximum compression [Pa] 36 60 Voltage [V] / Frequency [Hz] 230 / 50 - 60 230 / 50 - 60 Rated current [A] 0.072 0.138 Engine speed [rpm] 2400 2000 Engine power [W] 12 18 IP protection degree [-] X4 X4 Noise [dB(A)] 34 35 Installation instructions In order to accomplish the installation of the device successfully and enable the safe usage of the fan in the future, it is essential to follow the instructions in this manual. Before installing and connecting the fan, check that it has not been damaged during transport or storage (breakage, distortion). Check whether the technical data on the nameplate corresponds to the electrical installation parameters. The device should be mounted on a flat surface. If irregularities are not found, you can proceed with the installation as follows: - prepare appropriate electrical wires - mark the location of mounting holes - drill the holes and put expansion bolts in them - place the fan in the right place and tighten screw it - connect the device to electrical grid The electrical connection must be in accordance with the wiring diagram in the terminal box. Warnings and precautions During the operation of the device, the following precautions must be observed: - before performing any work, the device must be disconnected from the power supply - the fan is intended only for ventilation of rooms with small and medium cubature - if you do not use it for a long time, it is recommended to disconnect the device from the power supply - a constant supply of fresh air to the room must be ensured - do not use the fan in a hazardous environment (i.e. near flammable materials, in a heavily polluted one) or in a place where it could be exposed to direct contact with water - fan working temperature range is from -15oC to 40oC - some elements of the fan can become hot and touching them may cause burns - unusual sounds during fan operation may indicate a malfunction - failure to comply with the guidelines contained in this manual may result in damage to health or pose a threat to the life of the user Maintenance Maintenance of the device should be carried out depending on the working conditions, but not less than once a year. Before starting any maintenance operations, disconnect the fan from the power supply and secure it against uncontrolled turning on. In order to clean the fan it is necessary to: - disassemble the device (remove the panel, housing, rotor) - wash all parts with a damp cloth, taking care not to wet engine - never use water at temperatures higher than 60oC, gasoline, benzene, thinner or any other organic solvent - dry all elements thoroughly - re-install the fan - connect the fan to power supply Wiring diagram Device versions 1) With time switch (models with "T" index) The fan with timer switches on when it receives power. Then the device will continue operation for 1 – 30 minutes (depending on the settings). The time can be adjusted with appropriate knob. 2) With humidity sensor (models with "H" index) The fan with the humidity sensor switches on automatically when the humidity level in the room exceeds the set level, then it works until the level falls below the set level and subsequently continues operation according to the time set on the time switch (so-called delay time). Timer settings can be adjusted in the range of 1 - 30 minutes and the relative humidity sensor in the range of 60 - 90%. The values (delay time or humidity level) can be adjusted with appropriate knobs. 3) With motion sensor (models "MS" index) The fan with the motion detection sensor switches on automatically when the sensor detects motion in the sensor's operating area (semicircle with the set diameter), then it works until the movement stops and subsequently continues operation according to the time set on the time switch (so-called delay time). Timer settings can be adjusted in the range of 1 - 30 minutes and the range of the motion sensor from 0.5 m to 8 m. The values (delay time or range of the motion sensor) can be adjusted with appropriate knobs. Terms of warranty I. Reventon Group Sp. z o.o. [Ltd.] is the supplier of the fans and provides 24-month warranty period for VELO and VELO Silver series. II. The terms of warranty are valid from purchasing the device (the date issuing a document confirming the purchase of the device) but not further than 30 (thirty) months from leaving the supplier’s warehouse. III. The claim will be considered only if the document confirming the purchase (eg. copy of the invoice) and description of the fault is provided. IV. The supplier is committed to consider the claim within 14 working days since the date of reporting (i. e. day when documents given in point III are provided). V. Under the guarantee the supplier provides a repairment, replacement or refund for the defective device within a specified time limit. VI. Warranty does not cover mechanical damage, degradation of the quality related with time passing and defects resulting from improper exploitation / maintenance or arbitrary repairs and modifications. If there is any of the above, you will be charged for transport and / or repairs. VII. The supplier do not cover the dismantling / mantling costs. VIII. All correspondence should be send to the following address: Reventon Group Sp. z o.o., 556 Wyzwolenia Street, 43-340 Kozy, Poland or on e-mail: [email protected]. The supplier Reventon Group Sp. z o. o. reserves the rights to make changes in the technical data.